Question about 1994 Toyota Camry

1 Answer

My cigarette is not working i checked the fuse and they are good how can i fix? Also how to change 3rd brake bulb do i have to remove the cover inside the car or is it in the trunk please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 138 Answers

Cigarette lighter itself most likely the problem, burn out with frequent use.

Posted on May 14, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rear left brake fuse


The brake lights work off of the same fuse so if 1 light is working then the fuse is good. Check the plug where the bulb goes in. Make sure you have a tight and clean connection there. Test for voltage at the plug with the bulb removed.

Jan 30, 2015 | 2004 Jeep Grand Cherokee

2 Answers

My additional brake light is not working i have tested the brake unit and that works is there a seperate fuse for this or is it all on one fuse for all the brake lights


The third or High Mounted Brake Light runs straight off the brake light switch on the brake pedal arm. You say you tested the "brake unit"? I assume you mean the third brake light assembly, and if you get power there when someone steps on the brake pedal, then the bulbs are bad.

The power flow for the brake lights goes like this: Fuse ->Brake switch -> Turn signal switch -> Rear lights. The only difference is, if you have a 3rd brake light in your rear window, that gets its power directly from the brake switch. It does not go thru the signal switch first. So, if you are having a brake light problem, and your fuses are good, check the 3rd light in the rear window, if it lights up (assuming the bulbs are good, no one ever changes them), then the problem is most likely in the turn signal switch, hope this helps!

Aug 28, 2011 | 2002 Ford SVT Focus

1 Answer

1997 monte carlo. 3rd brake light works, but tail lamp brake lights do not.


The 3rd brake light working does reveal that the fuse is good, and the brake switch is good. Check the bulbs, sockets, and the wiring between the brake lights

Jul 04, 2009 | 1997 Chevrolet Monte Carlo

2 Answers

No brake lights but 3rd light works all fuses are good


Sounds like a broken wire somewhere.
Since the middle brake light works I would suspect it is somewhere in the trunk or close to the back seat.
Buy or make a tester. A 12v light with a clip on one wire that you clip to a good ground on the car the other wire with a sharp point. Turn the turn signals on then poke wire to rear lights until tester lights. When tester lights you know the break is somewhere inbetween the tester and the brake lights.

Hope this helps.

Stan

Apr 16, 2009 | 1985 Buick Skylark

2 Answers

My third brake light dosen't work on my chevy s10 94'


I had a similar problem with my 1994 S-10 LS extended cab. Both tail brake lights worked fine. I removed the 3rd brake light cover and tested for voltage at the steel center of the two rivets and found the positive (driver side) negative (passenger side) were good. I checked the two metal strips that send power to bulbs and found the positive side was open. Seems the flared side of the rivet was not making contact with the metal strip. I bucked the rivet with a punch and hammer and it took care of the problem.

Mar 17, 2009 | 1994 Chevrolet S-10

1 Answer

Rear Brake Lights not working, 3rd light is working


check the fuse for the stoplights. Even though the 3rd one is working it should be on a different fuse. With both of them not working even after you changed the bulb it would seem to lead to a fuse.

Feb 09, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Brake lights do not work (3rd brakelight does) changed bulbs checked fuse


Problem could be the Brake Light Control Module. That's about the only other thing other than a bad wire somewhere if the bulbs and fuses are good. 91 Accord has 2. One on each side in the smaller of the 2 rear tail light lenses. In order to change the module you have to remove the smaller of the rear tail lights. Drivers side is 5 pin. Passenger side is 6 pin.

Jul 20, 2008 | 1991 Honda Accord

1 Answer

Brake lights


do you have a 3rd brake light like on that is on the roof or in the rear window? if so does it work?
the brake lights are usually a 2way bulb so just because the lights work doesn't mean that brake lights will. if the 3rd brake light works replace the brake light bulbs if none of them work including your 3 brake light. check into having your brake switch changed. that is the switch under the brake pedal. when it is pressed the brake lights come on and when released they go off. if the bulbs do not fix the problem than try the switch.

Jul 19, 2008 | 1987 Honda Accord

Not finding what you are looking for?
1994 Toyota Camry Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...