Question about 2000 Ford Expedition

1 Answer


Posted by on

  • yadayada
    yadayada May 14, 2010

    U must remove the fuel tank to get the fuel pump changed.



1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

Pull back the carpet in the cargo area, there might be a panel you can remove to get to the pump. If there's not a panel, you'll have to take down the fuel tank. Hope it's empty. Did you make sure you didn't just run out of gas? Does the pump whine when you turn on the key? if it does, the pump is good.

Posted on May 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2000 ford expedition stalls when i get up to speed... I have changed all spark plugs and changed a coil that the auto parts store said to on number 7 and i still have the same problem with the stalling...

This can only be a guess since I don't have the mileage. Around a 100k on the odometer and fuel filter never changed..
No filter then the screen on the fuel pump inside the tank.

Feb 14, 2014 | 2000 Ford Expedition

1 Answer

Changed out fuel pump in 05 expedition and no power to fuel pump

check the fuse and fuel pump relay.if they are good then you will have to probe the fuel pump feed wire from the relay to the pump.also check the ground circuit for the pump.did you make sure the connection at the pump was clean and fastened securely

Nov 02, 2011 | 2000 Ford Expedition

1 Answer

I want to know what's the normal pressure on the 2000 expedition fuel pump

Here is the normal fuel pump pressures for the 2000 Ford Expedition with the 5.4L SOHC Vin L >>

Key ON Engine OFF (KOEO) 35-45 psi Key ON Engine Running (KOER) 28-45 psi

Here are your pressures if this is the 4.6L SOHC >>

Key ON Engine OFF (KOEO) 30-45 psi

Hope this helps with your concern...

Sep 13, 2011 | 2000 Ford Expedition

1 Answer

My ford expedition won't start i change the fuel

If it a diesel then you must be aware that when changing a filter and pump they must be full of fuel, otherwise it won't **** the fuel into the engine.

Jul 11, 2011 | 1997 Ford Expedition

2 Answers

2000 Ford Expedition fuel pump shut off switch - where is it located

Your owners manual should tell you where the fuel pump shut-off switch is located. It is usually located behind the right hand front kick panel near the top.

Nov 19, 2010 | 2000 Ford Expedition

2 Answers

Will not start. turns over when i spray starting

First you need to verify that the pump is getting power. Did you check the Inertia Switch? Power goes through that switch to the fuel pump. If the switch is good, and getting power,the fuel pump is most likely bad, the fuel tank must be lowered to replace the fuel pump.

May 24, 2010 | 2000 Ford Expedition

1 Answer

How to change the fuel pump on a 2000 ford expedition

Removal & Installation


1. Disconnect the negative battery cable.
2. Relieve the fuel pressure.
3. Raise and support the vehicle.
4. Remove the fuel tank; refer to the procedure outline in this section.
5. Remove the fuel pump retaining bolts.
6. Remove the fuel pump.

To Install:
7. Thoroughly clean the fuel pump-mounting flange.
8. Install a new gasket and place the pump into the tank.
9. Ensure that the fuel tubes face toward the fuel rail and tighten the retaining bolts to 80-107 inch lbs. (9-12 Nm).
10. Install the tank as outlined in this section.
11. Tighten the fuel tank bolts to 66-91 inch lbs. (7.6-10.4 Nm).
12. Tighten the fuel tank straps bolts to 22-30 ft. lbs. (29.7-40.7 Nm).
13. Tighten the skid plate bolts to 9.3-12.7 ft. lbs. (12.7-17.3 Nm).
14. Connect the negative battery.

Dec 20, 2009 | 2000 Ford Expedition

1 Answer

Car do not start fuel pump inop.2000 ford expedition 4.6 liter

fuel pump went out; my suggestion is to support vehicle and lower gas tank and change the fuel pump

Dec 27, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
2000 Ford Expedition Logo

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides