Question about 1998 Chevrolet C1500

Open Question

How do you remove the rear moulding for rear speakers

How do you remove the rear moulding to remove the rear speakers of a 1998 c1500

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the horn location under hood of a 2007 mercury mountneer?


Remove the LH front fender splash shield !
Fender Splash Shield Removal and Installation
  1. Loosen the running board bolts and lower the running board to access the front fender moulding pin-type retainer.
    • To install, tighten to 23 Nm (17 lb-ft).
  1. Remove the lower pin-type retainer from the front fender moulding.
  1. Remove the 2 rear pin-type retainers from the front fender moulding.
  1. Position the front fender moulding aside and remove the splash shield lower screw.
    >
  1. Remove the front splash shield screws.
  1. Remove the front splash shield pin-type retainers.
  1. Remove the front splash shield.
  1. Remove the front fender splash shield.
  1. To install, reverse the removal procedure.

Mar 25, 2015 | 2007 Mercury Mountaineer

1 Answer

Removing tail light housing on a 1998 chevrolet c1500 van


1 Remove the upper quarter panel appliue
2Remove the nuts(2)that retain the tailam to the upper quarter panel
3Remove the center high mounted stop;am(2)from the center high mounted aplique

Feb 27, 2013 | Cars & Trucks

1 Answer

How do I remove the headliner?


first remove pillar mouldings, and moulding around rear window, and in between front and rear doors. . Remove the dome light casing and unplug wires. Headliner will pop off

Jan 22, 2013 | 2000 Saturn L-Series

1 Answer

Driver's door moulding peeled off.


If you still have the moulding go to the local parts store get 3m brand trim adhesive and acetone fingernail polish remover clean the area the molding is to be applied to with windex the acetone. clean the back of the moulding the same way lay a thin line of clue on the moulding and press in place clean any excess glue with acetone prior to it curing

Feb 27, 2011 | 1998 Volkswagen Jetta

1 Answer

Rear speaker wire-which is positive which is negative?


1990 to 2008 Chevrolet Silverado C1500 Car Stereo Wiring Guide
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Good luck and this should help

Dec 26, 2009 | Chevrolet 1500 Cars & Trucks

1 Answer

Rear windscreen wiper V70 1998


Pull, and the plastic clips will disengage.  Some will break, there is nothing you can do about that.  Best to make a run to the dealer and pick up a handful of extra clips for the ones that do break.  There are tools that help prevent the clips breaking but they'll still break and it's not worth it.

Aug 08, 2009 | 1998 Volvo V70

1 Answer

How to remove lens on rear license plate light


you dont the bulbs twist out from the back side carefull or damage may occur to them from the outside

Apr 28, 2009 | 1998 Chevrolet C1500

1 Answer

1998 GMC Sierra (C1500) 5.0L 305 V8-right rear brake line


i dont know of any recall for that
and yes it can be replaced without removing the bedeasy wasy too do it is go too auto zone and buy a roll of brake line and run it along side of the old one and just leave the old one in the hangers and use tie straps too hang the new one!!!

Apr 20, 2009 | 1998 GMC Sierra

1 Answer

Cabin air filter


it;s under the cowl vent panel.

Cowl Top Vent Panel Removal
  1. Remove the windshield wiper pivot arm (17526) . Refer to Section 01-16 for the removal procedure.
  1. Remove the front door weatherstrip (20530) to access the windshield outside side moulding screws.
b981661.gif
  1. Remove the five windshield outside side moulding screws and the windshield outside side moulding (03136) .





  1. Pull the windshield outside moulding (03144) from the windshield glass (03100) .
  1. Remove the three Phillips-head screws from the cowl top vent panel (022A68) .


9bc8ed6.gif

  1. Remove the three plastic screws by turning them 90 degrees to unlock.





  1. Remove the six pushpins from the front edge of the cowl top vent panel .
  1. Lift up on the cowl top vent panel and disconnect the windshield washer hose (17A605) at the Y-connector.





  1. Remove the cowl top vent panel .

Mar 15, 2009 | 1998 Mercury Villager

1 Answer

1998 Chevrolet C1500 Speed Sensor


Hello, the steering position sensor just snaps into the bottom of the steering column. remove the steering shaft at the bottom of steering column, then slide the sensor off

Sep 08, 2008 | 1998 Chevrolet C1500

Not finding what you are looking for?
1998 Chevrolet C1500 Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...