Question about 1991 Daihatsu Charade

Open Question

How to replace the front wheel bearing of haihatsu mira 1991

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: replace front wheel bearings

The bearings in your car are pressed into a hub. If the part is available as an assembly, it can be replaced that way. Generally on a front drive car:
Remove wheels and brake calipers
If it is pressed in: remove the rotors, disconnect the drive shafts and remove the steering knuckle. Then the old bearing is pressed out and the new one pressed in with a machine shop press. If the bearing is part of the hub, that will be unbolted and the new one swapped.

On a scale of 1-10 difficulty, Id rate it a strong 7

Posted on Jun 20, 2008

Ad
kaokensho
  • 2 Answers

SOURCE: how to replace front wheel

I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Posted on Aug 15, 2008

CMV9
  • 594 Answers

SOURCE: replacing a front wheel bearing

here is a step by step instructions on how to replace your bearing. please copy and paste the link into your browser for an image.

please do not forget to rate and comment about your experience with fixya today.

Removal & Installation

  1. Apply the brakes and hold in place.
  2. Raise the vehicle.
  3. Remove the front tire and wheel assembly.
  4. Remove the cotter pin, lock nut and spring washer from the hub nut.
  5. While the brakes are applied, loosen and remove the hub nut on the end of the driveshaft.
  6. Release the brakes.
  7. Remove the front disc brake caliper and adapter as an assembly, and the brake rotor from the steering knuckle.
  8. Remove the nut attaching the outer tie rod to the steering knuckle. To do this, hold the tie rod end stud with a wrench while loosening and removing the nut with a standard wrench or crowfoot wrench.
  9. Remove the tie rod end from the steering knuckle using Remover, Special Tool MB991113.
  10. Remove the tie rod heat shield.
  11. Remove the nut and pinch bolt clamping the ball joint stud to the steering knuckle.

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during removal. Hold the bolts stationary in the steering knuckles while removing the nuts, then tap the bolts out using a pin punch.
  12. Remove the two bolts attaching the strut to the steering knuckle.

    NOTE Use caution when separating the ball joint stud from the steering knuckle, so the ball joint seal does not get cut.
  13. Separate the ball joint stud from the steering knuckle by prying down on lower control arm and up against the ball joint boss on the steering knuckle.

    NOTE Do not allow the driveshaft to hang by the inner C/V joint; it must be supported to keep the joint from separating during this operation.
  14. Pull the steering knuckle off the driveshaft outer C/V joint splines and remove the steering knuckle.

    NOTE The cartridge type front wheel bearing used on this vehicle is not transferable to the replacement steering knuckle. If the replacement steering knuckle does not come with a wheel bearing, a new bearing must be installed in the steering knuckle. Installation of the new wheel bearing and hub must be done before installing the steering knuckle on the vehicle.
  15. If the wheel bearing and hub need removal. Do not reuse the wheel bearing.
    http://www.chiltonlibrary.com/content/images/32050/images/32050_ptcr_g0035.gif The separation of the ball joint and the knuckle
To install:
  1. Slide the hub of the steering knuckle onto the splines on the driveshaft C/V joint.
  2. Install the steering knuckle onto the ball joint stud aligning the bolt hole in the knuckle boss with the notch formed in the side of the ball joint stud.
  3. Install a new ball joint stud pinch bolt and nut. Tighten the nut to a torque of 70 ft. lbs. (95 Nm).

    CAUTION The strut assembly-to-steering knuckle attaching bolts are serrated and must not be turned during installation. Install the nuts while holding the bolts stationary in the steering knuckle.
  4. Position the lower end of the strut assembly in line with the upper end of the steering knuckle and align the mounting holes . Install the two attaching bolts. The bolts should be installed with so that the nuts face towards the front of the vehicle once installed. Install the nuts. Holding the bolts in place tighten the nuts to a torque of 40 ft. lbs. (53 Nm) plus an additional 90° turn after the specified torque is met.
  5. Place the tie rod heat shield on the steering knuckle arm so that the shield is positioned straight away from the steering gear and tie rod end once installed. Align the hole in the shield with the hole in the steering knuckle arm. Install the outer tie rod ball stud into the hole in the steering knuckle arm. Start the tie rod attaching nut onto the stud. Hold the tie rod end stud with a wrench while tightening the nut with a standard wrench or crowfoot wrench. To fully tighten the nut to specifications, use a crowfoot wrench on a torque wrench to turn the nut, and a wrench on the stud.
  6. Tighten the nut to a torque of 40 ft. lbs. (55 Nm). Install the brake rotor, disc brake caliper and adapter.
  7. Clean all foreign matter from the threads of the driveshaft outer C/V joint. Install the hub nut in the end of the driveshaft and snug it.
  8. Have a helper apply the brakes. With vehicle brakes applied to keep brake rotor and hub from turning, tighten the hub nut to a torque of 180 ft. lbs. (244 Nm)
  9. Install the spring washer, lock nut and cotter pin on the hub nut. Wrap the cotter pin ends tightly around the lock nut.
  10. Install the tire and wheel assembly. Install the wheel mounting nuts and tighten them to a torque of 100 ft. lbs. (135 Nm).
  11. Lower the vehicle.
  12. Set the front toe on the vehicle to required specification.

Posted on Apr 17, 2009

blueextc3221
  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

  • 142 Answers

SOURCE: Replacing front wheel bearings

It isn't a particularly hard job but there are a few techniques that you need to know.
I wouldn't recommend you do it yourself but I would recommend you do it under supervision of someone who knows their stuff.
Retensioning the bearings correctly is extremely important.

Posted on Jun 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 wheel bearing replace


If you are talking about the front, it is generally replaced as a assembly, wheel bearing/hub assembly, that runs about 40-60 bucks. You will likely need a puller to remove it easily, relatively simple job with a good puller.


Mar 17, 2013 | 1991 Mercury Topaz 4 Door

1 Answer

CHANGING THE FRONT WHEEL BEARING 1991 ACCORD


Parts book shows both a bearing and a hub assembly so it depends on your situation.
To replace a bearing, you have to remove the wheel and brakes, then disconnect the spindle and the axle shaft.
Not something a DIY can do in a driveway without some major tools.

Jul 01, 2012 | 1991 Honda Accord

1 Answer

My 1991 cavalier is a 2.2ltr 4 cyl. 3spd auto, front wheel drive. when I drive it I hear from the right (passenger side) front tire a deep loping whirring sound....I am leaning towards the bearing or...


Deep growling sound could well be a bad wheel bearing. A bad cv joint will generally make a click or clacking sound, usually while only turning. While driving, you can often change the pitch of a bad wheel bearing with a slight turn of the steering wheel (note - slightly, no crazy zig-zag). What you're doing is shifting the weight on/off of this bearing and the pitch will change if it's bad. Only way to verify is to remove it and feel it in hand. It's a sealed hub/bearing assembly and only replaceable, not serviceable.

Jun 20, 2010 | 1991 Chevrolet Cavalier

1 Answer

What type of front wheel bearing for toyota camry DX,1991, v6


It is a fairly large double row bearing on this front wheel drive car, Any auto parts store, or dealer will get you the right part, and they are not something that is easy to replace, I suggest you to please take it to a qualified mechanic as it takes some tools you probably don't have. Hope this helps.

Apr 27, 2010 | 1991 Toyota Camry

1 Answer

1991 Pathfinder rear wheel bearing replacement.


According to my owners manual, you have to remove the entire brake assembly and pull the axle shaft to replace the bearings. The bearings are pressed in and require a special tool to remove them. Not a job I'd take on myself.

Oct 29, 2009 | 1991 Nissan Pathfinder

1 Answer

91 pontiac firebird front left wheel stuck


maybe wheel bearings? the smoke could be from the bearing grease.

Aug 04, 2009 | 1991 Pontiac Firebird

2 Answers

Left front wheel shakes at all speeds


Check front ball joints. Pre load hub bearings to right Torque.

Jun 14, 2009 | 1991 Chrysler New Yorker

1 Answer

Front spindles


ok... replace them....inspect the bearings and replace if necessary....
Robert
and have the cv joints inspected as well.

Sep 05, 2008 | 1991 Nissan Sentra 2 Door

Not finding what you are looking for?
1991 Daihatsu Charade Logo

Related Topics:

271 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...