Question about 2000 Audi TT

1 Answer

Turn signal is not working fuses and bulbs are good

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 138 Answers

Usually hazard light switch faulty, turn signal relay built into switch.

Posted on May 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Ford f250 brake lights and turn signals won't work - checked all fuses, flasher and bulbs and all are good, what could problem be??


Well the brake light and turn signal circuits are on two different fuses, but they both go thru the turn signal switch.
So I would start by checking for power in and out of the turn signal switch for each circuit.

Apr 07, 2013 | 1990 Ford F250

1 Answer

My saturn signal light work sometime than go off if it the flasher please tell me there it is in my car


IF TURN SIGNAL LIGHT DONT WORK SOME TIMES.CHECK FOR BLOWED OR LOOSE FUSE.CHECK TURN SIGNAL BULBS AND CHECK BULB SOCKETS FOR CORROSION.CHECK TURN SIGNAL FOR BAD GROUND.USE JUMPER WIRE BETWEEN GROUND SIDE OF THE TURN SIGNAL BULBS AND A GOOD CHASIS GROUND.IF ALL IS GOOD TURN SIGNAL SWITCH IS BAD OR FLASHERS GOING BAD.TURN SIGNAL FLASHER LOCATED ON CENTER CONSOLE SIDE PANEL GRASP THE FLASHER UNIT AND DETACH IT FROM THE FUSE BOX.IF YOU HAVE EARLY MODEL VECHICLE FLASHER UNIT LOCATED AT THE FRONT OF THE FUSE BLOCK.

Aug 23, 2011 | Saturn LS Cars & Trucks

3 Answers

Both my right & left turn signals aren't working but hazards are


If you can locate the hazrd flasher unit under the dash on the drivers side, the turn flasher unit should be right beside it and looks the same. Unplug and switch the 2 flashers and see if the turn signals work. The flasher unit is a silver and round. they are usually close to the stering colum. Let me know if that helps.

Mar 27, 2011 | Dodge Durango Cars & Trucks

2 Answers

The turn signals do not work but the 4 ways do i have already replaced the flasher and the fuse what else can it be


If the fuse and the flasher are good and we know the wireing is good because the hazards work then you are down to the turn signal switch [unless you replaced the wrong flasher].

Nov 12, 2009 | 1994 Mercury Grand Marquis

3 Answers

Blower motor and turn signals stopped working


CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL IS GOOD.CHECK TO SEE IF BLOWER IS GETTING POWER.IF NOT.SWITCH IS BAD.IF YES REPLACE BLOWER MOTOR.IF TURN SIGNALS STOP WORKING.CHECK FUSE FIRST.IF FUSE LOOK GOOD. CHECK BULBS TO SEE IF THEY ARE BLOWN.IF BULBS LOOK GOOD PROBLEM COULD BE WORN OR CORRODED BULB SOCKETS OR.BAD GROUND.OR THE TURN SIGNAL SWITCH IS BAD.

Aug 24, 2009 | Plymouth Voyager Cars & Trucks

2 Answers

No turn signals, no tail lights and fuses are good


Replace the non-working tail light bulb. Try replacing the bulbs for the turn signals. If that doesn't work, replace the relay.

May 24, 2009 | 1995 Isuzu Rodeo

1 Answer

Turning signals not working


The way the system works is:
The fuse supplies 12 volts to the flasher unit then leaves the flasher and goes to the turn-signal switch in the steering column.
When you set the turn-signal switch to turn right or left, the switch sends that 12 volts to the front and rear bulbs. The voltage goes through the bulb, lighting the bulb and goes to ground.
If any of these components are not good than the lights will not work.
Check the fuse and make sure it is good, the fuse will be located under the hood at the fuse center.
Let me know if you have a test light and we can proceed from there.
Regards,

May 09, 2009 | 2001 Chevrolet Blazer

2 Answers

1993 Dodge Shadow...left turn signal won't flash


If the fuses are good and the front and rear bulbs are good, change the flasher for the turn signals, even tho the right is working. If that doesn't fix the problem, it might be in the turn sgnal switch on the steering column.
If both bulbs are good for the backup lights and fuses are good, then the backup light switch, which is screwed into the side of the transmission has to bad.

Apr 12, 2009 | 1993 Dodge Shadow

1 Answer

Lt frnt turn signal bulb and lt headlamp not working, replaced tu


probably need headlight bulb too, check fuses first.

Jan 10, 2009 | 2002 Volkswagen Jetta TDI

1 Answer

Trun signal no op. fuse good and bulbs good


are the turn signals not working on both sides? If yes, replace the turn signal flasher, located on the fuse block.

Nov 29, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
2000 Audi TT Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14363 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...