Question about 1996 Toyota Corolla

1 Answer

Hi, changed master cylinder rubbers on my ae 110 corolla. Front left brakes are binding now. Tries to change the flex line but only got a right side to use on the left wheel. Car is still binding. What to do

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 6,927 Answers

Replace the caliper if the hose has been changed

Posted on May 14, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ok i replaced the master cylinder brake booster and bleed all lunes from left to right all the way around still no pedal what is wrong

well you should make sure the brake fluid is coming out freely by loosening the lines and let the fluid run free if it dont come out free you may have to change the flex line thats at the front and if the rear carry a flex line and it dont come out free change them as well, now you should always start from the wheel nearest to the master cylinder and make sure all bubbles or foams come out clear,another thing when bleeding your brake you should place something under the pedal so it wont go strait to the floor and you should have breaks,and if your car carry abs make sure its not leaking anywere,check around the pump

Jun 16, 2014 | Cars & Trucks

1 Answer

Having problems bleeding 94 toyota corolla brakes

Remove the master cylinder & take out the
piston & clean inside

Replace all rubber flex hoses & any calipers & wheel
cylinders over 8 years old

Flush System

Dec 16, 2012 | 1994 Toyota Corolla

2 Answers

Right front brake is not working. Don't see any fluid leaking. Considering master cylinder but any other ideas before changing this. Pedal goes out once a week

Hi and welcome to FixYa!

The master cylinder is surely worn out. The right side piston seal is surely stuck and replacement will surely be necessary to make it loose and make the brakes work again.

Hope you find this information helpful enough and thank you for using FixYa! Have a good one!

Jan 30, 2011 | 1995 Buick Regal

1 Answer

I have a brake binding problem i changed the master cylinder twice,change the flexible brake lines and changed the seals of the front calipers and cleaned the pistons of the calipers too.

If you have a frozen caliper, (rusty piston stuck inside calipers cylinder), then you have to options:
Replace the caliper piston and sea,l with a new one, or replace all thing i.e, the caliper. Hope will help.

Sep 07, 2010 | 1996 Toyota Corolla

1 Answer

Brake bind while driving all four wheels i change the master cylinder booster rubber line and calipers

may have a bad brake caliper if it's locking down while driving, most likey cause,hope i helped!

Aug 16, 2010 | 1996 Toyota Corolla

1 Answer

Toyota corolla ae110 brakes binding

Please DO NOT drive in with the vehicle in this condition!!!!
What you have going on is that the brake caliper (part that holds your brake pads) is bad and sticking. Just remove it, get a NEW one from any chain autoparts store,and replace it. You will have to get a new set of pads as well,as due to the binding, the ones on there now are trashed.

Again,PLEASE do NOT drive in this condition as yours and your fellow drivers ,as well as your passengers safety is at stake.

May 01, 2010 | 1996 Toyota Corolla

3 Answers

1998 plymouth breeze left rear brake stays on

Your E-brake cable needs a to be loosened up and you need to see if the E. Brake is locking up, if the cable is not frayed then you have a problem with a check valve in the master cylinder or in the T where the line goes to the left and right. If you want to know how to check out the hydraulic problem it is more detailed, but first you must make sure that the mechanical part is not binding up.

Jun 15, 2009 | 1997 Plymouth Breeze

1 Answer

Right front brake drags

Replace the flex line the rubber line between the car and the caliper. The inside of flex line can collapse making the back flow to release the caliper extremely slow. You can confirm the line is the problem by doing two tests. Pump the brakes up and undo the line at the caliper and it should release the caliper. Pump them up again and then undo the flex line at the steel line going to the master cylinder this should not change anything. Let me know if your findings are different and we can go from there. Mike

Jan 05, 2009 | 1991 Oldsmobile Bravada

1 Answer


your lf caliper is frozen check rubber flex line also

Nov 16, 2008 | 1991 Acura Legend

Not finding what you are looking for?
1996 Toyota Corolla Logo

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8589 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides