Question about 2001 Dodge Ram 1500 Truck 2WD

Open Question

I need to reconnect a rocker arm on a 2002 dodge ram truck with a 4.7L engine. I need directions

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2002 dodge ram 2500 diesel

I'm no expert, but I am on my second Dodge. I have a 2004 Ram 2500, 125k miles on it. I traded in my 2001 1500 with 99k on it.
Your problem sounds like one of two things that happened to me. At 110k mi's it was not accelerating properly, particularly between 40 and 50 mph. It turned out my torque converter was going bad and I ignored it for too long and it's disintegrated pieces ruined my transmission. I recommend getting over to Aamco right away or to the dealer if you are still in warranty and have the TC checked out. The diesel is just too much torque for a torque converter on the automatic transmission, but manuals are too much of a pain these days. $2300 at Aamco to have the TC replaced and the tranny rebuilt.

The new problem I have now is when it acted like it was out of fuel and then wouldn't turn over after it died. My fuel lift pump (diesels have two of everything and the expensive one is always what goes) has gone bad and is currently being replaced, $700 part, plus another few hundred in labor.
Hope this helps.
B

Posted on Oct 28, 2008

Ad
  • 37 Answers

SOURCE: 2002 dodge ram truck

The check valve on the fuel line at the filter housing may be leaking back not maintaining pressure when the engine is not running.

Posted on Dec 08, 2008

  • 1 Answer

SOURCE: speedometer not working on 2002 dodge ram 1500

Removed cluster from dashboard and unplugged & turned the whole cluster clockwise very slowly and needle started moving from 150 mph back down to 0 mph when rotation was completely done. Kept cluster upright while re-installing and plugged back in the plugs on back and everything was fine. Called local Dodge dealer and told me would take 30-45 minutes to reset and would cost approximately $70 to fix. Took about 8-10 minutes of my time and saved myself $70. This may not work for everyone but this was my amazing quick fix thanks to GOD for giving me this thought to try this.

Posted on Jul 19, 2009

dttech
  • 4803 Answers

SOURCE: I have a 2002 Dodge Ram where vent selection won't change

Your heating and air conditioning system is controlled by the Body Control Module (BCM). Any diagnosis should begin with scanning the (BCM) for trouble codes to determine the source of the problem and/or which circuits and components are involved.

If a failed mode door actuator is, in fact the problem, the instrument panel must be removed to gain access to it.

Posted on Oct 17, 2009

  • 52 Answers

SOURCE: 2000 dodge truck code po203 po204

p0203 injecter circuit malfunction cyl #3. p0204 injector circuit malfunction cyl#4. po138 02 sensor circuit,high voltage cylinder bank no.1,sensor no.2

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the rocker arm torque specs on a 1996 dodge caravan 3.0 liter


Hi Derrel,here's a link to a Autozone repair guide on your rocker arms,you can join their site like me for free and use all their repairs guides,need more help,let me know,k. Repair Guides Engine Mechanical Rocker Arm shafts AutoZone com

Aug 29, 2016 | 1996 Dodge Caravan

1 Answer

Cost to replace lifters in a 1999 dodge ram 5.2


Did someone tell you, you needed lifters? I have done maybe five jobs in 40 years that the lifters were the problem. Most times is the push rods and rocker arms. Pull a valve cover and see how clean it is. Sludge build up? Or just dirty oil. Being a 99 and if it has high miles, I would go with an engine swap.

Mar 14, 2015 | Dodge Cars & Trucks

1 Answer

I removed rocker arm assembly and did not line up timing marks did i waste the car 2005 dodge neon sxt


If you removed the rocker arms then the exhaust valves will all be closed and so will miss the pistons. How ever if the inlet valves were not working and the rocker arms were still in place then there may be damage to inlet valves.

Jan 25, 2015 | Dodge Cars & Trucks

1 Answer

I have a 2003 Dodge Ram 1500 4.7 with 166k still ticking after lifters replaced.


If there was a problem that caused the rocked to become dislodged I would have checked the rocker bushes and shaft and replace both. The rocker where it works on the end of the valve wears a recess that will move and then click back into place. I would use a 20w-50 grade oil and additives work at reducing friction . IF you need it to thicken the oil then there is something worn out.

Apr 04, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

I own 2002 dodge durango 4.7 replaced heads lifters chater what the problem


They are either not getting enough oil or the rocker arms are to loose.

Oct 26, 2012 | 2007 Dodge Ram Truck

1 Answer

What is the rocker arm tourqe specs on my 2005 dodge ram 5.9 l diesel


Hi.. The Rocker arm should be torqued to 36 N.m ( 27 Ft lbs)
I hope this help on your question. Thank you for use fixya

Aug 17, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

I need torque specs on rockers and lifters for a 2005 dodge ram 2500 5.9 24 valve diesel engine


Lubricate the crossheads and push rod sockets and install the rocker arms and pedestals in their original loca-
tions. Tighten bolts to 36 N·m (27 ft. lbs.) torque.

Don't forget to adjust your valve lash.

here is a link to the Factory Service Manual

Jul 28, 2010 | 2005 Dodge Ram 2500 Truck

2 Answers

Rocker arm come out on jeep chrysler 3.7 eng


A rocker arm is the arm that sits on top of the valve stem and connects to the push rods 'the push rods sit on the cam so when engine is running, the push rods go up and down in a timed sequence and with the rocker arms, open and close the inlet and exhaust valves. the rocker arm is located inside the valve(rocker)cover .If the rocker arm gets loose or comes out.
Check the nuts on the shaft which holds the rocker arms.either the shaft or nuts are got loose.They need to be tightened.Don't make it too tight or too loose.  Too tight,and they don't flutter right. Too loose,and they allow the rocker arms to wiggle out of whack. Other possibility can be  something is broken, bent, collapsed, or out of adjustment. 
Thanks. you can rate this solution and show your appreciation.



May 20, 2010 | 2002 Jeep Liberty

1 Answer

Dodge v10 rocker arms breaking


Talk to mopar. That's a warranty issue & b.s. if you ask me. Rocker's breaking off,beep, that.

Jun 22, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Proper installation instructions for Rocker Arm Installation 1998 Dodge 5.9 360.


locate v8 on crankshaft damper(147 degrees ATDC). rotate engine until v8 lines up with TDC mark on timing cover. install rocker arm and pivot assemblies and torque to 21 ft. lbs. wait 5 minutes before starting vehicle to allow lifters to bleed down correctly

May 19, 2009 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...