Question about 1984 Ford F 350

1 Answer

When i start the truck it goes in gear fine but after it runs for a min it wont go in gear it just clanks but if i turn it off and back on again it will go in gear

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 333 Answers

Check to make sure your transmission fluid level is where it should be

Posted on May 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, Car will start fine and runs perfect, however after a long run (1/2 hour or more) wont start straight away wait 10 mins and away it goes, turns over fine just doesn't fire


Loss of spark ? CK coil or coil pack or ignit relay. Any CK engine lts? coolants sensor or temp sending unit.? Is it running hot?

Sep 04, 2015 | 2003 Hyundai Santa Fe

2 Answers

Changed transmission fluid on crv now car wont start


might be that you accidentally disconnected the crank sensor close to the transmission, this gives a no start condition without a check engine light on most cars...

Apr 19, 2014 | 2005 Honda CR-V

1 Answer

94 ford ranger manual transmission goes into first gear and reverse just fine let off the clutch and the truck wont move.


part of a clutch job is removing the gearlever make sure the lever is secured properly and selects the gear correctly.
Orherwise your symptoms sound like a collapsed pressure plate or broken release bearing either defective part or something done wrong during installation of clutch

Apr 13, 2017 | Cars & Trucks

1 Answer

1995 sl1


replace ignition coil

Jun 20, 2013 | Saturn Cars & Trucks

1 Answer

Clanking noise coming from Allison Transmission on a 2001 Chrevrolet Silverado 8.1 Liter engine


this does sound like theres a loose line tapping the engine/frame,during warm up the engine idles faster which could make it vibrate faster causing the the clanking or tapping noise,if this has started after trans fluid change,then check the lines running from the trani to radiator sometimes the service person might bang into something causing plastic clips that hold the lines to break,try getting under it and have someone start the truck and listen to see where it's coming from also hold the lines & see if the noise stops,the service guy could have unbolted something & never put the bolt back causing the clank ex.line may have a clip holding it thats bolted to the trani pan ?good luck

Dec 29, 2012 | 2001 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...