Question about 1998 Chevrolet Blazer

1 Answer

Security system lock out of starting - 1998 Chevrolet Blazer

Posted by on

  • boomer2277 May 13, 2010

    your very helpful i`ll try that for a solution thank you again

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

Put the key in the ignition, key ON, flip switch in opposite direction, then turn the key off and the LED in your dash area goes on solid.

This should reset the alarm, and reset the grounded relay on the starter wire, allowing you to start the engine. Just Repeat these steps to place it back to usable armed mode. You may get 2 chirps, confirming it, and the lights may flash twice as well. That should do it.

A relay and resistor setup is needed to bypass. See PAASLOCK2.COM for the proper methods avail.

But, if you want to just remove this system from the equation entirelly,
I suggest the PLJX bypass kit to get around this issue.

This Passlock Bypass Module is designed to momentarilly allow the engine to remote start by sending a proper coded pulse to open the fuel rail passlock injector cut off circuit.

The output from an alarm/remote starter would then shut down the pulse, once it has detected the engine has engaged, and preserve the integrity of the passlock system.

The charts can be gotten for all cars at www.vehiclewires.com or www.passlock2.com

Hope this help.

Posted on May 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you put the resistor in the passlock system on a Oldsmobile Alero


You don't say if the security light is lit ? Is it ? If not , it's not a anti-theft system problem . An the passlock system on your vehicle the passlock sensor is part of the ignition lock cylinder . No resistor ! If the security light is lit you need to have it check for codes . There are a number of DTC'S that can set .
DTC B2947
DTC B2948
DTC B2957
DTC B2958
DTC B2960
DTC B3031
DTC B3033
DTC P1626
DTC P1630
DTC P1631
DTC P1632

The Passlock™ system is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate or the ignition switch is operated while separated from the ignition lock cylinder case. The body control module (BCM) provides security system sensor power and low reference for the Passlock™ sensor. The BCM also measures the security system sensor voltage.
When the correct key is used to start the vehicle, a magnet on the lock cylinder passes close to the Passlock™ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock™ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle. The BCM will measure the voltage on the security sensor signal circuit and compare this voltage to a previously learned voltage. If the voltage measured is within the valid range, the BCM will send a class 2 message to the powertrain control module (PCM) to enable vehicle starting. If the voltage measured is not within the valid range, a class 2 message will be sent to the PCM to disable starting of the vehicle.

Nov 04, 2016 | Oldsmobile Cars & Trucks

1 Answer

Keyless fob lock out


Alarm System Operation & Diagnosis - Range Rovers

www.rangerovers.net/repairdetails/becm/alarm.html
(If done by the key, a press on the remote locking button is still required before .... the BeCM goes into a 10 minute lockout mode (30 minutes for 1996 and later ..... buttons at the dealership, you may need to reset the code on the fob - which is ...

How to reset the security lockout on a Saturn Vue

www.kittycatonline.com/.../How-to-reset-the-security-lockout-on-a-Satur...
Nov 30, 2014 - How to reset the security lockout on a Saturn Vue. ... Now, though, not only does the "phone start" system still fail to function, the remote start fob now fails to work as well. ... the Passlock system starts out in what I'll call "agressive" mode. ... basically disabling it: Get the original factory remote unlock key fob, ...

Jan 08, 2016 | Cars & Trucks

2 Answers

Whr is my fuel pump reset button on my 2003 grand am? Its security lock, it wont get any fuel. It cranks but wont start. Not getting any fuel. First time ever happening


There is no reset button.
The problem could be the anti-theft system which would knock out the injectors and spark to the plugs.
If the security light is staying on, the problem could be the chip in the key.

Oct 26, 2015 | Cars & Trucks

1 Answer

Security system


These are easy systems. Lock down the truck. Open the door with the key. Doesn't work on the drivers side, lock it, unlock the passenger side, then reach in to unlock the drivers side. Still no start? look under the driver side for an after market security system. Remove it and repair wires as you go. Still no start after this, Have the codes read. Could be both door latches are bad or the BCM?security.

Aug 25, 2015 | 1997 Dodge Dakota

1 Answer

How do you bridge-out the anti-theft security system....it keeps kicking in and shutting down the van after starting


There is a problem detected within the security system by the security module. Try locking and unlocking the door with the key fob to reset the system. Sometimes locking and unlocking the drivers door using the key will reset the system as well. If still no luck, try the spare key to see if the security system accepts it

May 02, 2015 | 2001 Ford Windstar

1 Answer

I just installed a new key switch in my 2006 trailblazer it is a napa part now when I start it it will only run for a few seconds and die ?


That is because of the vehicle theft deterrent system ! Do you have a security light lit on the instrument cluster ?
The Passlock?"¢ System is provided in order to prevent vehicle theft if the ignition lock cylinder is forced to rotate or the ignition switch is operated while separated from the ignition lock cylinder case. If starting is attempted without authorization from the Passlock?"¢ System, the powertrain control module (PCM) will disable engine starting. Start disable may be in the form of fuel disable or starter disable, depending on engine application.
The components of the Passlock?"¢ System are as follows:
?€¢
The ignition lock cylinder and key


?€¢
The ignition lock cylinder case, including the Passlock?"¢ sensor


?€¢
The ignition switch


?€¢
The body control module (BCM)


?€¢
The security indicator on the instrument cluster


?€¢
The powertrain control module (PCM)

Ignition Lock Cylinder Case, Including the Passlock?"¢ Sensor
The ignition lock cylinder fits inside the ignition lock cylinder case and operates the ignition switch when turned by a key with the proper mechanical cut. When the ignition key is used to turn the ignition lock cylinder to crank, start, a magnet on the lock cylinder passes close to the Passlock?"¢ sensor within the ignition lock cylinder case. The magnet activates the security hall effect sensor in the Passlock?"¢ sensor which completes a circuit from the security sensor signal circuit through a resistor to the security sensor low reference circuit. The resistance value will vary from vehicle to vehicle.
If a magnet from outside of the ignition lock cylinder case is used to attempt to steal the vehicle, the tamper hall effect sensor will be activated. This completes a circuit from the security sensor signal circuit through a tamper resistor to the security sensor low reference circuit bypassing the security resistor. If the ignition switch is forced to rotate without the correct key, or if the ignition lock cylinder is removed by force, the Passlock?"¢ sensor will be damaged and will not operate.

Feb 22, 2015 | 2006 Chevrolet Trailblazer

1 Answer

Why the security light is on?


do u have a power remote lock and key? if so shut all the doors and unlock the vehicle then try to start.. also it can be in security mode and wont start because it thinks its being stolen. read the manual about security lock and it should tell you how to lock and unlock the system

Jul 05, 2014 | 2001 Chevrolet Impala

1 Answer

Why won't my car start when the security lock is shown on dash panel


That symbol indicates the security system is activated and the engine is locked out, if you believe this to be in error you will need the system scanned to find out what part is causing the system to lock you out.

Nov 02, 2012 | Cars & Trucks

1 Answer

Problem with the security system Jeep cherokee '95


To reset the alarm, you have to lock everything back up and then use the key to unlock the tailgate FIRST. After that, you can unlock any of the doors with the key without the security system locking everything off.

(Needless to say, I gained familiarity with this situation from personal experience!)

May 21, 2009 | 1995 Jeep Grand Cherokee

2 Answers

2000 Alero Security light flashing and wont start


With the new lock cylinder in it, turn the key on. The security light should blink. Leave the key on for 10 minutes, the security light will quit blinking and go out after 10 min. This will reprogram your security system and the car should start. Also leave a battery charger on it while the key is on, If the battery goes dead during the 10 minute reprogram sequence, you will have to start over again.

Mar 08, 2009 | 2000 Oldsmobile Alero

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...