Question about 1999 Ford Expedition

1 Answer

How to replace a ignition lock cylinder in a 99 ford expedtion

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 708 Answers

I believe you are talking about the cylinder where the key goes that starts the truck. If so, you will need to go to autozone and borrower there steering wheel removing tool. When I did mine it took about 2 hours to do. They have a step by step instruction on how to do it that they can print off. Its not hard to do, I could probably do it in 30 minutes or so now. You have to disconnect the battery to prevent air bag deployment.

Posted on May 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove to replace key ignition of 99 solara


Can't get the link to post but a Google search og 1999 Toyota solar ignition lock cylinder replacement gave several results.

Oct 16, 2016 | Cars & Trucks

2 Answers

99 ford explorer changed ignition now wont start


If your vehicle was towed, check the fuel pump intertia switch located near the top of the passenger side kick panel.
if you changed the key, you will be having an antitheft problem.
you could try putting an original key at the lock cylinder while turning the new key, it may allow it to start... if so, new key will require programming, or have the new lock cylinder coded to the old keys.

Jun 19, 2014 | 1999 Ford Explorer

1 Answer

How do I replace a ignition switch for a 1989 Cadillac deville


AutoZone Videos - Ignition Lock Cylinders

www.autozone.com/video/video.jsp?...Ignition+Lock...
AutoZoneFind Ignition Lock Cylinders videos at AutoZone.com. ... How to install an Ignition Lock Cylinder in a 95-2011 Ford. 14,972 views. Average rating of 4.4 out of ...

How to Remove and Replace an Ignition Lock Cylinder ...

? 5:13
https://www.youtube.com/watch?v=S9I4MnRIrHk
Sep 2, 2012 - Uploaded by RatchetsAnd Wrenches
How to remove and replace an Ignition Lock Cylinder on a 2003 Hyundai Elantra GT. If this video helped you ...

Aug 14, 2011 | 1989 Cadillac Sedan DeVille

2 Answers

The car will turn over but won`t start but if I turn the key on and jump the starter it starts


Sounds like the ignition switch has gone kaput. The ignition switch come in two pieces, an electrical switch and a mechanical switch.

The switch electrical portion can be replaced separatly from the mechanical portion (tumbler that the key engages). It is not a real difficult repair but requires some mechanical knowlege of how the column is assembled.

This can be verified with electrical test equipment prior to buying a new electrical switch.

Apr 18, 2011 | 1994 Volkswagen Golf

2 Answers

I lost my key for an 98 ford explorer and i just got a key made but wont trun the locksmith made a key from the door lock we put it in the ignition but it wont trun


There should be 8 cuts total on the key. While the door and the ignition share some of the same cuts you cannot get all the cuts from one cylinder. I believe that the door cylinder only uses 6 cuts and the ignition cylinder uses 7 cuts. The cut closest to the head of the key is #1 and the cut closest to the tip is #8. If I remember correctly the ignition cylinder uses cuts 1 - 7 and the door cylinder uses cuts 3 - 8.If the locksmith cannot decode the ignition cylinder you can try to contact you local ford dealer and see if they can find a key code and cut a key from that otherwise you may have to replace your ignition cylinder.

Apr 08, 2011 | 1998 Ford Explorer

1 Answer

Hello, I hope you can help me. I have a 1989 ford econoline van and I am trying to replace the ignition switch, but i can't get the old one out.


If you look under the the switch you will see a hole turn key on and push into the hole this should release it be carefull not to disturb the gear at the end or you will have to retime it.
Ignition Switch Lock Cylinder-Functional Lock Cylinder Removal
  1. Disconnect the battery ground cable (14301) and wait at least one minute. For additional information, refer to Section 414-01.
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Press the ignition switch lock cylinder release pin while pulling out the ignition switch lock cylinder.
    gg0795a.gif
Installation
  1. To install, reverse the removal procedure.
    • Verify ignition switch lock cylinder operation.
    gg0617a.gif

Feb 15, 2011 | Ford E-150 Cars & Trucks

1 Answer

Wrong Key was used in 99 Saturn sl1 now the ignition is completely locked up.


If the wrong cut key was used you are probly going to have to replace the ignition lock cylinder as the tumblers may be bent or the interior of the lock cylinder bent. Also recommend you replace the key. Thank you, bluebirdmate

Sep 10, 2010 | Saturn SL1 Cars & Trucks

1 Answer

Ignition switch replacment


Ignition Switch REMOVAL & INSTALLATION The ignition switch is located at the bottom of the ignition key cylinder body. To remove the ignition switch, first remove the ignition lock cylinder.

1993–99 Golf and Jetta
  1. Disconnect the negative battery cable.
  2. Center the steering wheel.
  3. Remove the air bag.
  4. Remove the steering column switches.
  5. If the vehicle is equipped with an automatic transmission, detach the shift lock cable from the lock cylinder housing.
  6. Remove the adapter sleeve from the steering column.
  7. Remove the spring and horn contact ring from the steering column assembly.
  8. Detach the sheer bolt.
  9. Insert the ignition key and unlock the cylinder, then detach the wiring connectors.
  10. Once all wiring has been detached, slide the housing off the steering column.
  11. Mark and drill the lock cylinder as shown and described in the above procedure.
  12. Compress the stop spring and pull the lock cylinder out of the steering column housing.
  13. Put the new lock cylinder into the steering lock housing.
  14. Insert the key into the lock cylinder.
  15. While you gently turn the key, insert the lock cylinder fully into the housing.
  16. The rest of the installation procedure is the reverse of removal. NOTE: Always use a new shear pin when installing the lock cylinder.

Jun 25, 2009 | 1998 Volkswagen Jetta

1 Answer

1997 ford contour


this is for 98, but may apply if yours is late 97 build.

Article No.
98-21-14
  • IGNITION SWITCH - HIGH EFFORT IGNITION KEY INSERTION/REMOVAL AND/OR KEY CHIMES SOUND WITH DOOR OPEN AND IGNITION KEY REMOVED
Publication Date: OCTOBER 15, 1998
FORD: 1998 CONTOUR LINCOLN-MERCURY: 1998 MYSTIQUE
1999 COUGAR
This TSB article is being republished in its entirety to include the 1999 Cougar . ISSUE: The ignition key may be difficult to insert or remove and/or key chimes may sound with the ignition key removed and driver's door open on some vehicles. This may be caused by internal design characteristics in the ignition lock cylinder increasing insertion/removal efforts which may allow the lock cylinder to stick.
ACTION: Install a revised ignition lock cylinder. The revised ignition lock cylinder should reduce the possibility of high insertion/removal efforts and ensure proper chime function. Refer to the following Service Procedure for details.
SERVICE PROCEDURE
  1. Verify customer concern.
  2. Observe the ignition lock cylinder as the key is removed. If the lock cylinder snaps outward to the non-depressed position and the chimes stop sounding, continue to Step 3. If it does not snap outward, replace the ignition lock cylinder with the appropriate cylinder by referring to the Parts Block in this article.
  3. Insert and remove the ignition key from the lock cylinder. If binding or high efforts are encountered, replace the ignition lock cylinder.
  4. From the Parts Block, select a lock cylinder with a part number suffix identical to the center character of the key code of the vehicle. The suffix must match the center key code character to maintain a single key system.
  5. Install the replacement lock cylinder, by referring to the 1998 Contour/Mystique Workshop Manual, Section 211-05 or the 1999 Cougar Workshop Manual, Section 211-04. NOTE: KEYS INCLUDED WITH NEW IGNITION LOCK CYLINDERS ARE CUT FOR THE IGNITION ONLY. IN ORDER FOR THE KEYS TO FUNCTION IN THE DOOR LOCKS, THE KEYS MUST BE CUT TO THE DOOR CODE OF THE ORIGINAL LOCKSET. THE KEY CODE WILL CHANGE UPON INSTALLATION OF THE REPLACEMENT LOCK CYLINDER (FIGURE 1).

    tw2114~us~en~file=tb5525a.gif~gen~ref.gif
    Figure 1 - Article 98-21-14

    NOTE: ADVISE THE CUSTOMER TO DISCARD ALL KEYS THAT WERE CUT TO THE ORIGINAL IGNITION LOCK CYLINDER.
  6. Record the new key code on the repair order and provide to the customer. Advise the customer to record the new key code in a permanent location and to discard all references to the original key code. NOTE: REPLACEMENT IGNITION LOCK CYLINDERS ARE SHIPPED WITH NON-PASSIVE ANTI-THEFT SYSTEM (PATS) KEYS. IF THE VEHICLE IS EQUIPPED WITH PATS, OBTAIN TWO (2) ROTUNDA KEY BLANKS (OR OTHER FORD AUTHORIZED BLANKS, SUCH AS: ILCO, STRATTEC, CURTIS, HUF, OR VALEO) AND CUT TO THE REVISED KEY CODE. USE OF OTHER UNAUTHORIZED KEYS MAY CAUSE ERRATIC OPERATION OF THE PATS SYSTEM.
  7. Program PATS keys using one of the two following methods:
(1) For vehicles with Integrated PATS (IPATS), function built into the Powertrain Control Module (PCM) and built beginning:
  • 2/2/98 Kansas City (Contour/Mystique)
  • 2/16/98 Mexico (Contour/Mystique)
  • All 1999 Cougars
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 3.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PCM
    • Enter Security Access (10 minute delay)
    • Ignition Key-Code-Erase
  2. Disconnect Data Link Connector (DLC).
  3. Cycle the first non-programmed key in the ignition to run position for at least 3 seconds and then turn to the off position.
  4. Cycle the second non-programmed key in the ignition to run position. The theft indicator should prove out for 3 seconds.
  5. Verify the vehicle will now start using both keys.
(2) For Contours/Mystiques with Stand Alone PATS and built before:
  • 2/2/98 Kansas City
  • 2/16/98 Mexico
Using the New Generation Star (NGS) Tester equipped with Service card (green) level 1.0 or higher:
  1. From NGS menu, select:
    • Service Bay Functions
    • PATS
    • Ignition Key-Code-Erase (this process may take up to 8 minutes to complete )
  2. Disconnect DLC.
  3. Cycle first unprogrammed key in the ignition to run position. First key will program and allow vehicle to start.
  4. Again cycle first programmed key to run position. Within 15 seconds, remove original key and turn new unprogrammed key to run position. The theft indicator should prove out for 2 seconds. New key will start vehicle.
  5. Repeat this process for additional key programming. NOTE: THE FOLLOWING SHOULD BE NOTED FOR THE PART NUMBER BLOCK:
    • Part Number suffix will match center character in key code
    • Logo on key is Ford for Contour models
    • Logo on key is Mercury for Mystique and Cougar models


PART NUMBER PART NAME F5RZ-11582-A Ignition Lock Cylinder (Contour) F5RZ-11582-B Ignition Lock Cylinder (Contour) F5RZ-11582-C Ignition Lock Cylinder (Contour) F5RZ-11582-D Ignition Lock Cylinder (Contour) F5RZ-11582-E Ignition Lock Cylinder (Contour) F5RY-11582-A Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-B Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-C Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-D Ignition Lock Cylinder (Mystique, Cougar) F5RY-11582-E Ignition Lock Cylinder (Mystique, Cougar

Aug 13, 2008 | 1997 Ford Contour

Not finding what you are looking for?
1999 Ford Expedition Logo

360 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...