Question about 1995 Honda Passport

1 Answer

Do i need any special tools to change hub bearing on a 95 honda passport

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

No special tools needed, this Honda has the old type inner and outer wheel bearing's, remove cotter pin, spindle nut slide rotor out, remove wheel bearing, repack new bearing with grease and don't forget to replace grease seal's, install new part's adjust spindle nut and install cotter pin.Good luck,hope this was very helpful.

Posted on May 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i check front wheel bearings on 95 honda passport to determine whether they need replacing


Drive 25 to 40 mph & listen to the noise

Remove the brakes & turn the wheel hub by hand

If you replace one side ,do both

Aug 15, 2014 | 1995 Honda Passport

1 Answer

How do i remove the front wheel hub on a 2003 honda civic?


Unfortunately the hub has to be driven or pressed out. This is usually a job that requires special tools not typically in the average person's tool box. Some people will try to pull it off with a slide hammer. That can work but you'll only be half-way there. You've still got to put it back once you replace the broken stud. One of the issues with removal of the hub is that you'll most likely have to replace the hub bearing because the inner race will be frozen to the hub shaft. Another job that'll require special tools. This is really a job for a shop. Sorry to be a downer. There are some youtube videos on-line that show this procedure. I'm confident that you can find one for your Honda. Good luck.

Aug 05, 2014 | 2003 Honda Civic

1 Answer

Changing front brake rotor on 1995 honda passport


Put the parking brake On and jack up the front of your SUV.

Remove the lug nuts and you will be able to remove the tire and rimm by sliding them off.Remove the spindle bolt located at the center of the rotor using an 36 mm socket(approx).

Remove the two nuts located behind the rotor (one at top and other at the bottom). This will enable you to remove the brake caliper.While removing it be careful that the caliper tube stays straight.

Slide under your passport and remove the 4 bolts behind the hub using an 12 mm(approx) wrench.Pull the hub assembly out and this will remove the hub rotor in some cases if you are using an tool for pulling the hub assembly out or you have to slide the rotor off the hub assembly.

Slide the new rotor into the hub assembly.Reinstall the brake caliper and make sure the caliper tube is not twisted. Replace the spindle bolt.

Nov 14, 2010 | 1994 Honda Passport

1 Answer

How to replace a Jaguar X Type fron wheel bearing


Jaguar 2000-06

Wheel Bearings
Removal & Installation
  1. Remove the brake disc.
  2. Remove and discard the retaining clip. Detach the ABS sensor.
  3. Remove and discard the O-ring seal.
  4. Remove the wheel hub and bearing retaining bolts.
  5. Remove the wheel hub and bearing.
  6. Prior to applying sealer, clean the ABS sensor sealing surface and the ABS sensor aperture sealing surface.
  7. Install a new O-ring seal.
  8. Apply a 2.5mm bead of Loctite Ultra Blue 587 Silicone (RTV) sealer to the ABS sensor sealing surface.
  9. Install a new ABS sensor retaining clip.
  10. Install the hub/bearing assembly. Tighten to 90 Nm.

  1. Remove wheel knuckle.
NOTE When removing the wheel hub from the wheel knuckle the bearing will be destroyed and the bearing inner ring will remain on the wheel hub.
d752c5a.jpg

Fig. Using special tools, remove the wheel hub-X-Type
  1. Using special tools, remove the wheel hub.
  2. Using a suitable tool, remove the bearing inner ring.
  3. Using special tools, remove the wheel bearing.
  4. 2125147.jpg

    Fig. Using a suitable tool, remove the bearing inner ring-X-Type

    ee51ce7.jpg

    Fig. Using special tools, remove the wheel bearing-X-Type

To install:

b506586.jpg

Fig. Insert special tool 204-312 in to 204-309-X-Type
  1. Insert special tool 204-312 in to 204-309.
  2. Support the wheel knuckle on special tools.
NOTE Make sure wheel bearing is correctly orientated with the colored side facing inboard.
  1. Align the bearing over special tool.
  2. Using special tools, press bearing into wheel knuckle.
  3. Change special tool 204-312 to 204-313.
  4. Align the bearing and wheel knuckle over special tool.
  5. Slide wheel hub over the guide and align to the bearing.
  6. Using special tools install the wheel hub.
  7. Install the wheel knuckle.

  8. 5a457fa.jpg

    Fig. Using special tools, press bearing into wheel knuckle-X-Type

    b9fcc3f.jpg

    Fig. Change special tool 204-312 to 204-313-X-Type

    be319f2.jpg

    Fig. Align the bearing and wheel knuckle over special tool-X-Type

    8a9e0dc.jpg

    Fig. Slide wheel hub over the guide and align to the bearing-X-Type
  1. Raise front of vehicle and support on stands.
  2. Remove appropriate road wheel.
  3. Using wire or string, secure brake caliper to road spring to take weight off brake hose.
  4. Raise vehicle sufficient to provide access for special tool 204-111.
  5. Install special tool 204-111 in road spring.
  6. Slacken tool adjuster to suit spring length.
  7. Install adaptor and thrust collar.
  8. Position stem of tool in center of spring passing dowel through slot in suspension turret.
  9. 24ce878.jpg

    Fig. Install special tool 204-111 in road spring-XJ Range and XK Range

    1d0063e.jpg

    Fig. Position stem of tool in center of spring passing dowel through slot in suspension turret-XJ Range and XK Range

NOTE When turning tool adjuster, ensure that tool stem does not rotate and disturb position of dowel in suspension turret.
  1. Engage dowel of special tool 204-111 in suspension turret and rotate to position across slot.
  2. Lower vehicle onto stands.
  3. Rotate tool adjuster to tension spring.
  4. Remove wheel speed sensor securing screw and withdraw sensor from vertical link.
  5. Remove nut securing tie rod outer ball joint to steering arm.
  6. Release ball joint from vertical link.
  7. Install special tool 211-098 on tie rod outer ball joint.
  8. Tighten tool bolt to release taper pin from vertical link.
  9. Remove special tool from ball joint and position tie rod for access.
  10. Remove nut securing upper control arm ball joint to vertical link.

  11. 3af9a83.jpg

    Fig. Install special tool 211-098 on tie rod outer ball joint-XJ Range and XK Range

continue...

Aug 03, 2010 | 2002 Jaguar X-Type

1 Answer

How to i change the bearing on the airconditioner


to change this bearing requires special mechanics tools. This job can quickly become a real pain if the bearing has been staked on. What level is your mechanical expertise? With all due respect if you do not have pullers and access to presses I would not try this project. At the minimum you will need snap ring pliars, a new bearing, a serpentine belt removal tool, a special puller and a press.
First remove the serpentine belt. In the center of the compressor pulley there may be a nut that needs removed, remove it. thread in the special pulley clutch removal tool as far as possible with the center bolt of the puller all the way out. With the tool threaded on tighten the center bolt on the tool until the pulley clutch comes off. this works best if you use an impact. now you should see the snap ring on the center hub. remove it. The hub with bearing should now slide off. If it doesnt you will have to use another special puller. Once you get that off you will have to have the bearing pressed out. Likely the outside race will be staked on. it helps if you can grind those off. A machine lathe works wonders for that job. Once the bearing is off put the new one on with the help of a press and a little locktite. You do not need to restake it as long as it fits plenty tight. the rest of the installation is pretty much the reverse of removal. The pulley clutch will need to be pulled on tight with a special tool with special attention given to the gap. You dont want it to touch but you want the clutch faces as close together as possible. good luck.

Jul 19, 2010 | 1996 Buick Park Avenue

1 Answer

How do i change front wheel bearing on a ford focus st2


SECTION 204-01: Front Suspension 2000 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/18/2003 Wheel Bearing
Special Tool(s) 15064.jpg Installer, Wheel Hub Bearing Cup
204-023 (T73T-1217-A) 21171.jpg Remover/Installer, Bushing
204-180 (T93P-5493-A) 15064.jpg Installer, Drive Pinion Bearing Cup
205-140 (T80T-4000-F) 205153.jpg Adapter for 303-224 (Handle)
205-153 (T80T-4000-W) d84l1123a.jpg Puller, Bearing
205-D064 (D84L-1123-A) 21217.jpg Installer, Wheel Speed Sensor Ring
206-054 (T93P-20202-A) Removal
  1. Remove the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.
  1. NOTE: When removing the hub from the wheel knuckle the bearing will be destroyed. The bearing inner ring will be on the hub and the bearing outer ring will be in the wheel knuckle.
    Using the special tools, remove the wheel hub from the wheel knuckle.
    e0027601.jpg
  1. ani_caut.gif CAUTION: The special tools must be used to prevent damage to the hub. If the hub is damaged a new hub must be installed.
    ani_caut.gif CAUTION: Do not use heat to remove the bearing inner ring.
    Using the special tools, remove the bearing inner ring from the wheel hub.
    e0027602.jpg
  1. Remove the circlip from the wheel knuckle.
    e0002134.jpg
  1. Install the old bearing inner ring.
    1. Install the bearing cage on to the bearing inner ring.
    1. Install the bearing cage and inner ring assembly to the wheel knuckle.
    w1401022.jpg
  1. Using the special tools, remove the bearing outer ring from the wheel knuckle.
    e0027603.jpg
Installation
ani_caut.gif CAUTION: Avoid any impact on the wheel speed sensor ring.
ani_caut.gif CAUTION: Make sure the wheel speed sensor ring is clean.
ani_caut.gif CAUTION: Avoid any contact between the wheel speed sensor ring and a magnetic surface.
  1. ani_caut.gif CAUTION: Make sure the wheel bearing is installed into the wheel knuckle with the wheel speed sensor ring, colored black, at the wheel speed sensor end of the wheel knuckle.
    Using the special tools, install the new wheel bearing to the wheel knuckle.
    e0027604.jpg
  1. NOTE: Make sure the circlip does not cover the wheel speed sensor.
    Install the circlip to the wheel knuckle.
    e0002134.jpg
  1. Using the special tools, install the wheel hub to the wheel knuckle.
    e0027605.jpg
  1. Install the wheel knuckle. For additional information, refer to Wheel Knuckle in this section.

Apr 05, 2010 | 2000 Ford Focus

1 Answer

1998 Mercury Mountaineer wheel bearing What tools are needed to change the front wheel bearing on a four wheel drive.


2x2 = nothing special since they are old fashion tapered bearings

4x4 = nothing special again BUT the wheel bearing is part of the hub assembly!

Jul 17, 2009 | 1998 Mercury Mountaineer

1 Answer

Replacing the front wheel bearings of a Honda Accord 1993 SE


yes you need a press to remove the bearing and hub , you can use the same hub as long as where the hub goes into the bearing is not scored in any way . the knuckle would have to be taken off and sent to a machine shop if you done have a press. and you should also use caution when putting the nut back on thr axle.

Feb 11, 2009 | 1993 Honda Accord

1 Answer

Change front wheel bearing 2001 ford escape.


you need to remove the spindle assy from the truck & press the bearing out & in   or you need to use a tool called the hub tammer to remove & install the hub bearing

Jun 28, 2008 | 2001 Ford Escape

Not finding what you are looking for?
1995 Honda Passport Logo

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...