Question about 2006 Hyundai Sonata

Open Question

Procedure for replacing evaporator core on 04 hyundai sonata

Procedure for replacing evap core

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

jpk528
  • 95 Answers

SOURCE: 04 sonata stereo wireing diagram

Battery ORANGE (+) RADIO HARNESS
Accesory YELLOW (+) RADIO HARNESS
Ground BLACK (-) RADIO HARNESS
LF Speaker (+) BROWN/WHITE
LF Speaker (-) BLACK/WHITE
RF Speaker (+) BROWN/YELLOW
RF Speaker (-) BLACK/YELLOW
LR Speaker (+) BROWN/RED
LR Speaker (-) BLACK/RED
RR Speaker (+) BROWN/WHITE
RR Speaker (-) BLACK/WHITE

Posted on Feb 20, 2009

alicantecoli
  • 22114 Answers

SOURCE: Color code for radio wires in Hyundai Sonata 2004?

look for the thickness of the wires ,or better still buy a ready made connector block that connects to the existing factory wiring

Posted on Sep 20, 2009

ghost45
  • 1280 Answers

SOURCE: Replace driver's side power mirror 2006 Sonata?

Go to www.hmaservice.com and register( Vehicle by VIN). Afterward, you have access to shop manuals, service bulletins, wiring diagrams, etc. about your vehicle.

Posted on Oct 03, 2009

  • 880 Answers

SOURCE: HOW OFTEN SHOULD I REPLACE TIMING BELT ON MY 04

The factory says 60K
Also you can see the service manual at www.hmaservice.com.

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Hyundai sonata and my check engine light came on and i read it for a o2 censor i replaced it and the a code came back for a incomplete Evap, i was wondering what that is and how to fix it?


Check your gas cap , u need replacement of gas cap and if that don't work u need to do smoke test on your evaporated system but first change the cap.

Oct 10, 2014 | Hyundai Motor 2003 Sonata

1 Answer

How to check and or replace evaporator core on2001 monte carlo?


To check it you need to pressurize the system run the compressor and then you can spray soapy water around it and see if you have a leak If you decide to replace the evap core for the ac be sure to replace the dryer as soon as you open the lines it will start to draw moisture and then the new system will fail or not put out cool air correctly. Unless you absolutely have to change the evap for the ac I suggest you leave it alone unless you have done this before or have someone to work with that know ac.

Jul 05, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

I need removal and installation proceedure of a/c evaporator for kia sephia with full details. please reply soon.


Its sais that steering wheel has to be removed,but actually its not necessary.The dashboardframehasto beremoved.Thatwill automaticallycome outwith sterring assemblyout.
For complete step by step procedure to replace Evap core.Click the link below:-----
http://autopartsdiagrams.blogspot.com/2013/09/how-to-replace-ac-evaporator-on-kia.html
---
This will help.
Thanks.

Sep 22, 2013 | Kia Cars & Trucks

1 Answer

Diagnostic code p0701


P0453 means EVAP emission pressure sensor high input. Possible causes:
- Faulty Evaporative Emission System (EVAP) Pressure sensor
- Evaporative Emission System (EVAP) Pressure sensor harness is open or shorted
- Evaporative Emission System (EVAP) Pressure sensor circuit poor electrical connection.
Code p0701 means Transmission control system range/performance. Possible causes:
- Open or short transmission control system circuit
- Poor transmission control system electrical connection
- Check powers and grounds to Transmission Control Module (TCM)

Aug 27, 2013 | Cars & Trucks

1 Answer

Moldy smell from ventillation


Many times small pieces of leaves and other organic stuff can get lodged in the evaporator core,making a musty stink.You will have to clean and disinfect the evaporator core to get rid of the smell.See if you can find a kit for this at a good parts store(like NAPA or Carquest)

May 04, 2012 | 2009 Hyundai Sonata

2 Answers

The light of engine goes on and the scan report says evap leak. since I live in a hot weather is this the problem. what should I replace?


HOT WEATHER HAS NO EFFECT, TRY REPLACINGF THE GAS CAP AND CLEARING THE LIGHT, IF THE CODE AND LIGHT COME BACK YOU WILL NEED THE DEALER TO TEST THE EVAPORATIVE EMISSIONS CONTROL SYSTEM COMPONENTS FOR A FAILED PART OR A LEAK.

Nov 05, 2009 | 2001 Hyundai Sonata

2 Answers

What is he code 455 for a 2006 hyundai sonata means


CODE PO455 EVAPORATIVE EMISSION SYSTEM LARGE LEAK DETECTED.POSSIBLE CAUSES CANISTER VENT SOLENOID MAY BE STUCK IN OPEN POSITION / EVAP CANISTER TUBE EVAP CANISTER PURGE OUTLET TUBE OR EVAP RETURN TUBE DISCONNECTED OR CRACKED OR CANISTER IS DAMAGED / EVAP CANISTER PURGE VALVE STUCK CLOSED OR CANISTER DAMAGED / FUEL FILLER CAP MISSING LOOSE NOT TIGHT OR THE WRONG PART / FUEL VAPOR HOSES TUBES BLOCKED OR RESTRICED OR FUEL VAPOR CONTROL VALVE TUBE OR FUEL VAPOR VENT VALVE ASSEMBLY BLOCKED /FUEL TANK PRESSURE SENSOR HAS FAILED MECHANICAL FAULT /FUEL TANK CONTROL VALVE IS CONTAMINATED DAMAGED OR HAS FAILED.

Oct 21, 2009 | 2006 Hyundai Sonata

3 Answers

04 sonata hard tostart after fueling


Sounds like the 'Purge Control Solenoid Valve' to me. The evaporative canister (charcoal canister) absorbs the vapors from the fuel tank).. sometimes this canister becomes 'saturated' and the 'PURGE CONTROL SOLENOID VALVE' sucks RAW fuel into the intake manifold (causing a 'flooding' fuel condition).. but ONLY if this valve is STUCK OPEN or LEAKING. Replace this valve.. go from there.

Jul 12, 2009 | Hyundai Motor 2004 Sonata

1 Answer

This is ''pops'' moore again!trying to save a $ You helped me before on the firing order.went to a/c guy.he tested system,said evaporator was bad and needed to be changed.his est.was my first born and a...


I assume he used a leak tester and found a leak in the evap which is inside the plenum housing. Need to remove the plenum to get access to the evap. big job. If you are technical, you could remove the plenum assembly and let him replace the evap & then let you out the plenum back in. Then take back to have him evacuate and recharge system.
-------------------------------
SECTION 412-03: Air Conditioning 1999 Town Car Workshop Manual
REMOVAL AND INSTALLATION Evaporator Core Removal and Installation
NOTE: The evaporator core is not separately serviceable. It is serviced only with the evaporator core housing assembly.
NOTE: Installing a new suction accumulator is not required when repairing the refrigerant system except when there is physical evidence of system contamination from a failed A/C compressor or damage to the suction accumulator.
NOTE: If an evaporator core leak is suspected, the evaporator core must be leak tested before it is removed from the vehicle. For additional information, refer to Section 412-00 .
  1. Remove the evaporator core housing. For additional information, refer to Section 412-02 .
  1. Transfer the components from the old evaporator core housing to the new evaporator core housing
  1. Install the evaporator core housing. For additional
  2. information, refer to Section 412-02
---------------------------------------------------------------------------
Evaporator Core Housing Removal
  1. Disconnect the battery ground cable (14301).
  1. Recover the refrigerant. For additional information, refer to Section 412-00 .
  1. Drain the radiator. For additional information, refer to Section 303-03 .
  1. Remove the screws and the RH cowl vent screen.
  1. Disconnect the vacuum hoses and the wire harness connector from the evaporative emission canister purge valve (EVAP canister purge valve) (9C915).
  1. Remove the nuts and remove the evaporative emission canister purge valve.
  1. Remove the heater hoses from the heater core.
  1. Remove the screw and reposition the windshield washer fluid reservoir.
  1. Disengage the four wire harness retainers from the top of the RH fender apron.
  1. Remove the RH front wheel and tire.
  1. Remove the screws from the RH fender apron and remove the fender apron.
  1. Disconnect the wire harness connector from the A/C cycling switch (19E561).
  1. Disconnect the wire harness connector from the blower motor (18527).
  1. Disengage the wire harness connector from the retainer.
  1. Disconnect the evaporator to compressor suction line from the suction accumulator/drier (19C836). For spring lock couplings disconnect and connect general procedure, refer to Section 412-00 .
  1. sxg~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To prevent damage to the fitting and the tube, use a backup wrench when removing the suction accumulator/drier.
    Disconnect the suction accumulator/drier from the A/C evaporator core.
  1. Remove the clamp screw retaining the A/C accumulator mounting bracket to the A/C evaporator core housing and remove the suction accumulator/drier.
  1. Disconnect the condenser to evaporator tube from the A/C evaporator core (19860). For spring lock couplings disconnect and connect general procedure, refer to Section 412-00 .
  1. Remove the RH instrument panel insulator.
    • Remove the pushpins.
    • Disengage the courtesy lamp holder.
    • Disconnect the power point wire harness connector and remove the RH instrument panel insulator.
  1. Remove the in-car temperature sensor hose and elbow from the evaporator housing.
  1. Remove the nuts at the top of the evaporator housing.
  1. Remove the nuts at the bottom of the evaporator housing.
  1. Remove the screw and nut near the blower motor.
  1. Remove the screws.
  1. Separate the housing and remove the blower motor and A/C evaporator core.
  1. Disconnect the wire harness connector.
  1. Remove the evaporator core cover.

Apr 06, 2009 | 1999 Lincoln Town Car

2 Answers

01 sonata gls v6...code po455, po442. what are these and how can I pass emissions test in arizona


If you have an EVAP leak, you will get the following codes:

1. P0442 evap emission control system leak (small).
2. P0455 evap emission control system leak (large).

If these codes come up, you need to trace the leak. The most common place for the systems to leak besides the gas cap is at the service port under the hood, the hoses at the purge solenoid, and the hoses around the fuel tank. Check all your EVAP hoses from under the hood , all the way back to the gas tank. You can repair a split hose easily. Buy some 14.5mm EVAP hose at the auto parts store. Just cut the split or cracked section out and attach the new hose.

I can only say that u must fix the code issue and light to pass state emission test, if u reset the light they will know, the system will tell the tester that the system is not ready, this will cause a fail.

Mar 16, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
2006 Hyundai Sonata Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...