Question about 1992 Chevrolet S-10

3 Answers

Broken belt on 1992 Chevy S10, 4.3 liter, 6 cylinder. Could it be any other belt other than serpentine? Money is tight and I want to know if it could be any other belt than the serpentine. I removed several small pieces and one thin one wrapped around the inner side of the fan blade.

Posted by on

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

There is only one belt, so you cant be wrong, although there are pulleys that tension the belt, feel all of them and be sure they spin freely without any noise. belts usually dont just break.

Posted on May 13, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

There is only one serpentine belt used in the 1992 S10. it sounds like your serpentine belt has come apart causing you to have several small pieces wrapped around the inside of your fan blade.
Inspect all your pulleys to ensure there is not one that is has gone bad causing your belt to fail. If money is tight, you may want to try the Salvage Yard to replace any pulleys like the idler and tension pulley that is the common cause for the belt to fail. Also you may get lucky and find a belt that is still good and most Salvage Yard will let the parts go for $5.00 if you pull it your self. Call around though, each Yard is different.
Thank you for using fixya and good luck.

Posted on May 13, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,468 Answers

The serpentine belt is the only belt in this p/u truck,its breaks off in strips the length of the belt

Posted on May 13, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Serpentine belt diagram for 2006 chevy hhr


https://www.google.com/url?sa=i&rct=j&q=&esrc=s&source=images&cd=&cad=rja&uact=8&ved=0ahUKEwiz1J6Bp5PUAhXEOyYKHaMJCgMQjRwIBw&url=http%3A%2F%2Fwww.serpentinebeltdiagram.com%2Fserpentine-belt-diagram-2008-chevrolet-hhr-4-cylinder-24-liter-engine-01126%2F&psig=AFQjCNEZHcIDH0OXdFTm1FeTs6pPI6E1Qg&ust=1496085519095928

May 27, 2017 | Cars & Trucks

1 Answer

Serpentine belt Diagram for 1988 chevy silverado 5.7 liter


Is this what you need? You said serpentine belt but my info showed three belts. If picture is wrong let me know.

25982247-q3wnknh4v5te2wmao3keqizj-2-0.jpg

Nov 27, 2015 | Cars & Trucks

1 Answer

Serpentine belt diagram for a 1987 chevy celebrity 4.5 liter 4 cylinder


buy a repair manual for 1987 chevy celebrity. Pepboys, Oreilly, etc.

Feb 17, 2015 | 1987 Chevrolet Celebrity

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    3 Answers

    I need a spark plug wire diagram for a 1992 Toyota Camry 4 cylinder


    1992 Toyota Camry Sedan
    3.0 liter DOHC V-6 (3VZ-FE)

    Cylinder # Front, passenger to drivers side 2-4-6
    Cylinder # Back, passenger to drivers side 1-3-5

    Distributor 12 O'clock post # 6 cylinder
    10 O'clock post #1 cylinder
    8 O'clock post #2 cylinder
    6 O'clock post #3 cylinder
    4 O'clock post #4 cylinder
    2 O'clock post #5 cylinder

    Good luck and hope this helps.

    Jan 12, 2010 | 1992 Toyota Camry V6

    1 Answer

    Replacing serpentine belt on 2000 chevy van need belt diagram


    My sincere apologies for the delayed response.
    I am personally going back to answer your unanswered questions.

    I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

    I am assuming this "van" is a Chevy Venture?
    CLICK
    on the following LINK. It has the Belt Diagrams you will need.
    If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
    Again my apologies...
    http://www.2carpros.com/car_repair_information/year/2000/make/chevrolet/model/venture/2000_chevrolet_venture_drive_belt_routing_diagram.htm

    Sep 21, 2009 | 2000 Chevrolet 2500

    Not finding what you are looking for?
    1992 Chevrolet S-10 Logo

    209 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    75051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7726 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...