Question about 1998 Ford Windstar

1 Answer

HOW TO FIX A FRONT HUB BEARING - 1998 Ford Windstar

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Go to the bone yard and buy the side that you need have new bearings pressed into it and then slowly disassemble the hub and replace with newly refurbished hub. be sure to mark your seams and threads with some spray paint so that you know where the original settings were at. had to do mine twice because I didn't press new bearings into the knuckle i bought at the bone yard.

Posted on May 15, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace front hub assembly 2002 Suzuki XL7


the front wheel bearing hub?
XL-7 (the dash matters)
my wild guess, is the questions was
what are all steps to do this job. and tools.
that?
RTM?

https://suzukipitstopplus.com/Products/10056-2002-grand-vitara-xl-7-service-manual.aspx

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer
the link shows all years, and variances.

here is a photo review, that is accurate up to
1998, and beyond , if you skip the bearing service parts. as yours are INTEGRATED
and NON-serviceable.
http://www.fixkick.com/hubs/FW_BEARINGS.html


the photo 6a and B
shows removing the hub,
so do that , buy a new hub and put it back
the same way, using the tool stated
at the stated ranges of torque
123-180 ft/lbs.
this range allows you to get the screws into the locking rings.

Dec 11, 2016 | 2002 Suzuki XL-7

1 Answer

Is there a trick to installing the bearing front end KIA sportage


Fix It Right! - Front Hub Bearing Replacement - YouTube

? 14:26
https://www.youtube.com/watch?v=l0LCkycUcqM
Sep 7, 2011 - Uploaded by OneSourceAutomotive
Front Hub Bearing Replacement (S1E3) Demonstrated on a 2004Kia Sedona FWD. ... on a front-wheel ...

Kia Sportage wheel bearing replacement - YouTube

? 4:10
https://www.youtube.com/watch?v=wa6NREeozbE
Apr 3, 2014 - Uploaded by Jo Daddy's Garage
I did a quick replacement of a bad rear wheel bearing/hub on aKia ... How to install front struts on a Kia ...

Dec 09, 2015 | Kia Cars & Trucks

1 Answer

I am trying to replace the passenger side hub and bearing,before i tear it down i need to know if the bearing is just pressed onto the new hub and then the whole assembly slides onto the splined end of the...


Hello texasjagfan: My name is Roger and I will help you. The front hub bearings are press out bearings and you will need a press in order to change them. You will need to remove the front spindle to gain access to the bearings.You also will need an alignment when finished replacing the front bearings. The rear bearings are a hub and bearing unit.
Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Aug 18, 2011 | 2003 Chrysler PT Cruiser

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

How do I change front hub and bearing assembly on 2004 Explorer


Front hub bearing, remove tire, remove caliper and caliper holding bracket, you do not have to remove brake caliper from brake hose, just set it aside, if 4X4 remove front axle nut that goes through center of rotor, also remove brake rotor, disconnect elec, A.B.S connector, remove three bolts on back side of hub bearing, remove hub bearing, some times you will need to knock hub bearing out with a hammer.Reverse to install new hub bearing.

Jul 09, 2010 | 2004 Ford Explorer

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

2 Answers

How do i replace the rear wheel bearing on my peugeot 206 1.9hdi year 2002 my rear wheel bearing has gone on my pug206 and i want to know how to fix, replace and repair myself i have bought the rear wheel...


wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Jul 20, 2009 | Peugeot 206 Cars & Trucks

2 Answers

Replacing front wheel hub assembly 1996 Dodge caravan


You can get a complete hub with bearing and its can just be bolted on, without having to have bearing pressed in and out. Good luck and thanks for using FIX YA

Mar 19, 2009 | 1996 Dodge Caravan

2 Answers

1995 Toyota Celica Front Wheel Hub


can u replace the bearing in the hub? will that fix your problem?

May 25, 2008 | 1995 Toyota Celica

Not finding what you are looking for?
1998 Ford Windstar Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...