Question about 1999 Dodge Caravan

1 Answer

#1 spark plug pop out and i can't screw it back in what shall i do?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,793 Answers

You need to helicoil the thread,not for the fainthearted,you may have to get it done by a main dealer if your not used to risking a new head.

Posted on May 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

New starter turns engine but will not fire


For the engine to run, it needs compression, fuel, and spark. having the proper tools for the ob is best but I will go with things readily available, without special tools.
Disconnect a spark plug and put a screw driver in the boot to touch the metal inside, place the shank of the screw driver close to metal, about 1/4 inch and crank the engine and look for a spark.
After cranking the engine, fuel should have got on the spark plug, remove the spark plug and check if it's damp or wet with fuel. Carburated engines are viewable if you operate the throttle and look down the carburator for squirting fuel.
With the spark plug off, stuff a rag on the threads where the spark plug threads into, don't fill the cylinder with the rag, just cover the hole by stuffing a rag on the threaded part, use a screw driver, then crank the engine, the rag should pop out of there during the compression cycle.
Apropiate tools needed is a spark tester, compression tester and fuel pressure tester and noid light. If you have these tools it is prefered you use them.

May 08, 2015 | Cars & Trucks

2 Answers

How do i get my 1996 chevy tahoe distributer back in time


Remove #1 spark plug ( front left ) stuff shop rage in spark plug whole. use screw driver to helt stop up hole just bump starter a few times till you hear a POP that will be top dead center #1 check timing pointer and marks front pully adjust top cemter place dist. in appropriate pos with roter in corect position

Mar 22, 2011 | Chevrolet Chevy Cars & Trucks

2 Answers

How do you replace the spark plugs on a 1998 2.7 Intrepid?


Hi,
REMOVAL
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • Prior to removing the spark plug, spray compressed air around the coil area and spark plug.
  • Remove electrical connector from ignition coil.
On 3.5L engines, it is necessary to loosen the screws by alternating back and forth. Do not lose the spacers under the coil when loosening the screws.
  • Remove 2 fasteners from ignition coil.
  • Remove ignition coil assembly.
  • Remove the spark plug using a quality socket with a rubber or foam insert.
  • Inspect the spark plug condition.
INSTALLATION
Always remove the ignition coil assembly by grasping at the spark plug boot, turning the assembly 1/2 turn and pulling straight back in a steady motion.
  • To avoid cross threading, start the spark plug into the cylinder head by hand.
  • 3.5L engines tighten spark plugs to 28 N·m (20 ft. lbs.) torque, 2.7L engine tighten spark plugs to 17.6 N·m (13 ft. lbs.).
  • Install ignition coil assembly onto spark plug.
  • Install coil screws and tighten: 2.7L engine to 6.2 N·m (55 in. lbs.), 3.5L engines to 6.7 N·m (60 in. lbs.).
  • Connect the electrical connector.

Aug 27, 2010 | 1996 Dodge Intrepid

1 Answer

Okay the car has new gasket and new wires and the spark plugs wires pops out of the valve cover why is that


If you bought after-market spark plug wires, that is not from a dealer, than sometimes the spark plug boot may be a tad short or loose on the spark plug and will slip or pop off. Take them back to the supplier in exchange for a better brand.

Mar 23, 2010 | 1992 Honda Accord

1 Answer

#1 spark plug pop out and i can't screw it back in what shall i do?


you will need to get a spark plug tap and rethread the hole, if that doesn't working it will have to be drilled out and retapped ,, will need that done by a mechanic

Mar 18, 2010 | 1999 Dodge Caravan

2 Answers

Firing order for Spark Plug wires


Here is the diagram you ask for. While it says it is for the 3.0L V6, it is the same for the 4.0L V6 if that's what you have...


2627ab5.jpg

Feb 15, 2010 | 2004 Ford Ranger

1 Answer

How do I repalce the spark plugs on my 2002 galant 2.4 4 cylinder engine


buy new plugs
set the gap on the new plugs
Label the plug wires (1-4)
pop the rummer cap where it goes into the cylinder head valve cover and remove the spark plug wire by grasping the shaft ot the spark wire and twisting it. Don't just pull on the wire as you can break it.
Cpat the threads on the spark plug with anti seize compund.
screw in the spark plug carefully so you don't cross thread it. Check a repair manual for torque specs; if you don't have a torque wrench, you want the spark plugs snug but not cranked down with all your strength.
Replace the spark plug wire and this is important, don't mix what wire goes where..

Jan 06, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

Number 2 spark plug wire keeps popping off spark plug


First, make sure the spark plug is in tight and not cross threaded (take it and put back in). If the plug is loose, pressure comes out of the cylinder and pushed the wire off.

Second, push the spark plug boot on and massage the air out of the boot.

Hope this helps.

May 13, 2009 | 1998 Toyota Corolla

1 Answer

Are the fuel injectors on the 01 expedition easy to replace on my own,I am ok doing the filter, and is there a trick to changing the spark plugs as well?


if you look at the front of your expedition on the passenager side as well as the driver side you will see a rail on each side there is two screws on the side of the rail remove the rail and lift up and then the injectors pop out and for the spark plugs you will need a long bar and socket that go on the spark plugs and be sure to put some anti-seize on the new spark plugs before putting them back in and also make sure all of your o-rings are on you injectors before putting them back in also pickup a small pack of grease for them at the autopart store before you put them back

Mar 26, 2009 | 2005 Ford Expedition

3 Answers

2004 dodge ram 1500 rear brake light out how to replace?


Open up the tail gate, you will see two torque screws on the inside beside the tail lights. take these out, this will free up the housing and you can change it from there.

Jan 11, 2009 | 2004 Dodge Ram

Not finding what you are looking for?
1999 Dodge Caravan Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...