Question about 1994 Mercedes-Benz C-Class

Open Question

How do I get the front bumper off of my 280c I need to remove it to repair a crack in it, and it is off of the first three tabs-so I need to know how to get it back on, too

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

bodyguy
  • 5 Answers

SOURCE: How to change the whole headlight assembly on a 05 Honda CRV

When you raise the hood, look for a Phillips screw that holds the parking lamp in. if it is there remove screw and pull parking lamp toward front of vehicle. If headlamp and side lamp are 1 piece, there should be 2 number 10 mm headed bolts that are vertical, that hold the assembly in. The side lamp will have a stud that holds the light to the fender. You may have to pry it loose. Reverse procedure to install.

Posted on Dec 23, 2008

  • 1596 Answers

SOURCE: replacing front bumper on 1999 buick regal

7/16th or 10mm Sheetmetal nuts All over Behind the Bumper Thak Bumper off first

Posted on Jan 16, 2009

  • 840 Answers

SOURCE: Trouble removing 1999 Solara Grille

sorry to tell you that but you must take the bumper off and its pretty easy there are retainers up top remove them remove the bottom of the bumper ones and they may have bolts now for the last part its 100 mm at the fender edge and bumper just slide off and then you can take and change the grille

Posted on Jan 27, 2009

  • 1596 Answers

SOURCE: Cracked front bumper on 1999 Chrysler town and country.

I Can not Locate Literature on the Subject but, I DO KNOW that the TRUE BUMPER is Located UNDER the COSMETIC COVER You SEE And they are Fairly EASY to Remove Mostly 10mm Bolts and PLASTIC Hold down Buttons, IT Is NOT DIRECTLY COnnected to AIR BAG There is A Number of INERCIA Type Sensor all around the Vehicle that Activates the AIRBAG. If this has Helped you and you feel I Deserve it PLEASE RATE Me, I Truly hope I have shed some light on your Project, Thank You
rejakwilson

Posted on Mar 26, 2009

sidlas
  • 95 Answers

SOURCE: I need to remove the front bumper cover in order

taking off the bumper is pretty easy ... i've done it plenty of times at work ... the good thing is that it comes off pretty simple without having to take off the headlamps or anything ... ok ... i'm gonna try ... open the hood ... take out the clips that are holding it on the top ... there's 5 of them i think ... then it's connected to the fender too ... remove the clips that connect the bumper to the fender liner on the side ... you're gonna need something like a clip remover for that cuz those sit pretty deep and are pretty hard to get out ... pull out the fender liner as far as you can and you'll see a screw that connects the bumper to the fender on the very tip of it ... i'm pretty sure it's a 7mm screw ... unscrew that and it should lossen up ... do that on teh other side too ... ok ... now ... bottom ... there are 7mm palstic screws on the bottom that hold the dirt blocker thing ... there's like 10 of them ... take out the cips and unscrew them ... the bumper should come off ... you might have to see what else is holding it ... but it's pretty easy ... top, sides, bottom ... doesn't matter which order you go in ... i usually start from the bottom ... then sided then top ... so yeah ... i hope this helps ...

Posted on Jun 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Detailed instructions on front bumper removal. NOTE: From all the videos, it appears the CAB is different than the sedan. An example is the grill does NOT come up with the hood.


Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

Oct 16, 2015 | 2003 Audi A4 Cabriolet

1 Answer

How to replace a 2001 Cadillac Eldordo front bumper


If you look around on the backside of the bumper, you should be able to find the bolts that hold it on, same with the grill. Look aound the bolts are pretty obvious. Just take out what you need to remove the bumper, a little tugging and pulling on the bumper might help find bolts that are easy to miss.. look around, you will find them.

Dec 15, 2013 | 2001 Cadillac Eldorado

1 Answer

How do you remove the front bumper to get to the radiator


If you need to remove the entire front bumper. Remove the 3 Phillips head screws in each inner fender (both sides edge of bumper by wheel). Remove the two 8mm bolts that you now have access to and go straight up (behind the inner fender). Remove the three 10mm bolts along the top of the radiator. Crawl underneath and pull the centers out of the plastic push clips (seven I think). Slide the bumper off.

Hope that helps, thanks for using FixYa.

Apr 10, 2010 | 1999 Dodge Caravan

1 Answer

I neede to remove the headlights for my 2008 E 350 and need instructions. OIt appears that removing the front bumper is needed ? Thanks


Here's some instructions for removing bumper and headlights.

E-Class W211 front bumper removal (standard body style).

Tools needed:
- Automotive wheel ramps (Rhino ramps from Autozone).
- 1/4" drive socket set with 8mm and 10mm sockets.
- #20 torx bit.
- Floor jack, optional but useful.
- Flat blade screwdriver.

Instructions for bumper removal:

1) Turn front wheels full right to remove push-pin fastener at lower front corner of left wheel well plastic splash guard. It's difficult to remove this fastener once the car is up on the wheel ramps.

2) Turn front wheels full left to remove push-pin fastener at lower front corner of right wheel well plastic splash guard.

3) Drive car up on wheel ramps. Block rear tires. Open hood.

4) Remove lower mesh plastic grille. There are five attachment points on the top edge of the grille. You can get to three of them with your hand by reaching between the radiator and the back side of the grille. The two outer ones can be released with a screwdriver also reaching in between the grille and radiator. Once the plastic tabs are released, you can remove the grille by pulling it out from the front of the car.

5) Remove the plastic panel located immediately behind the bumper from the bottom of the engine compartment. This panel is held in place with nine sheet metal screws with a 8mm hex head. Five screws are on the bottom of the car and there are two screws in each wheel well at the inner lower edge. After removing all nine screws you can work the panel free.

6) Disconnect the cable from each fog light and remove both fog lights. They are held in place by two sheet metal screws with a #20 torx head.

7) Remove the side marker bulbs. The one on the passenger side turns clockwise to remove and the one on the driver side turns counter-clockwise.

8) Remove the temperature sensor from its socket on the driver side.

9) If you have a floor jack, raise the car at the jack point on the cross member below the engine. You do not want to raise it off the wheel ramps. But it helps to have more clearance above the tires to work in the front wheel wells.

10) Remove three of the plastic nuts holding the forward half of the plastic wheel well liner in place. It's not necessary to remove the plastic liner. You just need to loosen it up so that you can pull it away from the fender to gain access to the screw and bracket securing the bumper to the fender.

11) Pull back the wheel well liner and remove the sheet metal screw from the rear end of the metal bracket . There is only one sheet metal screw (#20 torx head) holding this bracket in place. Don't attempt to remove the bracket yet. I used a #20 torx bit in a 1/4" socket with a 6-inch extension for a 1/4" drive wrench. The head of the screw faces the ground.

12) Remove the 5mm bolts (8mm hex head) holding the bumper to the headlight assembly between the small lens and large lens (both sides).

13) Remove the two 6mm bolts (10mm hex head) on either side of the large grille area opening.

14) Remove the two 6mm bolts (10mm hex head) securing the bumper to the bottom edge of the crashbar. You can access these bolts through the front where you removed the plastic mesh grille.

15) Remove the three 5mm bolts (8mm hex head) holding each headlight assembly in place. Two longer bolts are on top. One at the rear outer corner and one at the front inner corner. The third bolt is accessed from the bottom. It's in the area above the fog lamps. You don't need to disconnect the headlight cables and remove the assembly. But it helps to allow the headlight assembly to "float" freely while you disengage the bumper from the fender.

16) At this point all of the fasteners holding the bumper in place have been removed. The only thing left to do is to remove the two brackets "clamping" the bumper cover to the lower front edge of the front fenders. Before you do this, position some cardboard boxes, bags of packing material, six packs of paper towels, or other suitable items to protect the bumper in case it falls off the car.

17) The bracket holding the bumper cover to the fender has a "pin" that slips into a slot at the front edge of the bumper cover. There is a matching slot near the front edge of the fender. It's not possible to see this pin from the bottom of the car. Use a flat blade screwdriver to pry the bracket away from the bumper/fender and towards the center of the car. The bracket will "hinge" on the pin at the front end of the bracket. After you swing the bracket away from the bumper, you need to slide it forward to remove it from the slot in the bumper cover and fender. You will probably scratch some paint off of this bracket with the screwdriver. I recommend repainting the scratched areas of the bracket before reinstalling it.

18) After removing the bracket from each side of the car you need to deal with the small plastic "hook" holding the bumper cover to the very front tip of the fender. This hook is an integral part of the bumper cover. Disengaging this hook from the fender is probably the most difficult step of removing the bumper. Simultaneously raise the head light assembly slightly, push the leading edge of the fender outward slightly, and push the bumper cover inward toward the headlight assembly. Don't get too aggressive with the fender. It's aluminum and you will make a real mess if you apply too much pressure on the fender. It took me about 20 minutes to free each side from this hook. It should take you less time, since you now know that the hook exists!

19) Gently pull the bumper forward and away from the car. This is one step where a second person would be helpful. But I did manage to do this step alone. There is a "pulley" like attachment point on each side just below the fender/bumper seam.

To re-install the bumper, reverse the order of the steps above. When re-installing the bracket between the bumper cover and fender, I smeared a thin coating of car wash soap on the bracket to facilitate snapping the bracket back into place.




Oct 09, 2009 | Mercedes-Benz E350 Cars & Trucks

1 Answer

How do you take bumper of vw passat 2003 to replace radiator


Tools Required
--------------------------------
T25 Torx Screwdriver
Phillips Head Screwdriver (if equipped with fog lights)
Small Flathead screwdriver
Wide Flathead Screwdriver


Bumper Removal
--------------------------------

1. Jack the car up on both sides and remove the front wheels. Use Jackstands and please observe all safety procedures. I'm sure it's possible to do this by turning the wheels to each side as you work in the wheel wells, but this was easiest for me to do.

2. Remove the hood release lever.
Pry out the plastic guide on the front of the grill, and looking directly down on the hood release lever attachment point, you'll see a metal clip. Using your small screwdriver, flip that clip up so it's off of the plastic lever and place your wide screwdriver in the Y of the plastic, turn the large screwdriver to spread the Y off the pins that it is holding on to. This can be VERY frustrating, so take your time. If you need to remove the latch cover in frustration, it's a $6 part from Liberty (experience)

3. Remove the front grill.
Just a T25 torx screw on each side and clips underneath, be careful not to break the clips as you pull it off. If you have an aftermarket grill you might have to pull through or cut off your double-sided tape

4. Remove the 3 lower grills (they just pop out, the middle one is a little tricky, just take your time and make sure all the plastic clips release)

5. Remove fog lights (if equipped) 3 screws each and disconnect

5. Remove the 4 T25 screws from the top of the bumper (under where the grill just sat)

6. Remove 4 T25 Screws from each wheel well, one is pointed straight up, you'll have to feel under the wheel well where the bumper meets the fender to find it.

7. Climb under the car and remove the 3 flat head screws (they just twist out)

8. With your helper, pull the bumper straight towards you from each side, and remove the connections from the side markers. The bumper should now be free.

Installation is basically the reverse of removal HOWEVER, there are tabs on each side of the car that line up with tabs on the bumper, be absolutely sure that these line up, they will center the bumper for you and hold it on while you screw it in.

Removing Bumper strip
-----------------------------------

1. Looking at the back of the bumper that you just removed, find the 4 tabs and 4 hooks holding the strip on. The hooks are down by the side marker holes, and the tabs are on the front of the bumper.

2. You'll see a black pin holding one of the hooks in place, if you push with a small screwdriver on the bottom of this pin, you'll see another, smaller pin come up, pull this pin out as far as you can and the large pin will pop right out.

3. With your screwdriver, carefully pry back the tabs and pull on the strip from the front of the bumper, releasing it in sections.

4. After all the tabs are removed, pull the strip away from the bumper (as if you were pulling it from off from the front of the car, and it should come right off)

I hope help you woth this. Good luck (remember rated this help).

Oct 01, 2009 | 2003 Volkswagen Passat

1 Answer

Need to remove the broken bumper on the back of a 1994 Ford Taurus, buy a new one, and put it on. help.... also need to fix a crack in the front windshield.


check out the junk yard for the bumper it will be a lot cheaper and only 4 bolts on each side of bumper. sometime if the crack isnt big you can put a dab of crazy glue on the crack to keep it from spreading but it s smarter to replace the windshield

Aug 16, 2009 | 1994 Ford Taurus

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

Front bumper of 94 cad eldorado slipping on driver side - need to


There are 4 points of attachment for the front bumper. The nose has two long bolts that go through each of the 2 horizontal shock absorbers and screw into clips attached to the bumper reinforcement. You can access each bolt head with a long socket extension inserted in front of the fog lights.

The remaining two points of attachment are on the side of each of the front fenders, they are plastic guides that meet up with groves on the inside of the bumber sides, as you slide the bumper onto the reinforcement bumper, you line up the bumper groves with these plastic fender-mounted guides and you will reach a point where the bumper snaps in place.

I suspect the driver side bumper sliped out of the inner grove (best caes scenario), or the bumper goves cracked or the plastic fender-mounted guide cracked.

Get under the car to take a look, alternatively undo the 2 front nose bolts and remove the bumper, actually not a big job, and you will then be able to assess the problem.

Hope this helps.

Apr 05, 2009 | 1994 Cadillac Eldorado

1 Answer

Cracked front bumper on 1999 Chrysler town and country.


I Can not Locate Literature on the Subject but, I DO KNOW that the TRUE BUMPER is Located UNDER the COSMETIC COVER You SEE And they are Fairly EASY to Remove Mostly 10mm Bolts and PLASTIC Hold down Buttons, IT Is NOT DIRECTLY COnnected to AIR BAG There is A Number of INERCIA Type Sensor all around the Vehicle that Activates the AIRBAG. If this has Helped you and you feel I Deserve it PLEASE RATE Me, I Truly hope I have shed some light on your Project, Thank You
rejakwilson

Mar 14, 2009 | 1996 Chrysler Town & Country

1 Answer

Cracked front bumper on 1999 Chrysler town and country.


It is easy to remove, to crash sensors, they are further in

Feb 17, 2009 | 1999 Chrysler Town & Country

Not finding what you are looking for?
1994 Mercedes-Benz C-Class Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...