Question about 1999 Chevrolet Blazer

1 Answer

Drivers side brake light and horn won't work,,is it the multi function switch? 1999 chev blazer 4x4 . if so how much does a new one cost?

Posted by on

  • mcomrie2 May 13, 2010

    thx for a reply but, it's not the light,,it's in the wiring and the horn will NOT work at all, the guys checked it out and tell me it's a multi function switch at an outrageous cost and I need it fixed to pass the safety for my new playes and sticker.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Chevrolet Master
  • 3,854 Answers

No there not connected, replace the brake light
1999 Chevrolet Blazer Auto Light Bulb Size Guide
Low Beam Headlight Bulb Size: 9006
High Beam Headlamp Light Bulb Size: 9005
Parking Light Bulb Size: 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3057
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880 or 881
License Plate Light Bulb Size: 194
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 161
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168 or 211-2
Step/Courtesy Light Bulb Size: 168 or 211-2
Trunk/Cargo Area Light Bulb Size: 211-2
Under Hood Light Bulb Size: 93
Instrument-General Light Bulb Size: 161 or 37 or PC194 or PC74
Check Engine Indicator Light Bulb Size: PC74
Hi-Beam Indicator Light Bulb Size: PC74
Seat Belt Indicator Light Bulb Size: PC194
Brake Warning Light Bulb Size: PC74
Automatic Transmission Indicator Light Bulb Size: 194
Directional Signal Indicator Light Bulb Size: PC74
As for the horn, inspect the fuse and relay and most common it would be a bad ground wire or worst a bad horn due to corrosion. Horn will be located in the drivers side fender.
Thank you for using fixya.

Posted on May 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does brake assembly fail when I press pedal?


Check for loose contacts or wiring that is causing a short circuit near the brake pedal, or at the rear light.

May 17, 2013 | 1999 Isuzu Amigo

1 Answer

1999 chev 1500 4x4 new rebuilt trans won't move after 5 minutes


Well see whats wrong with it or cheak on google see what comes up he answer if my information aint helping you or go to a shop like morrisons

Jun 18, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 1990 Mercury Cougar. Several problems...Blinkers, hazards, horn, and break lights are not working. However the break light in the back window comes on when the break is pressed. Checked fused and...


I am unaware of what a "CO" display is.
Now with the blinkers, hazard, horn and brake lights not working that may be the multi funtion switch (blinker switch) that is located inside the column (where the blinker lever attaches).
Obviously the blinker, hazard and horn will all work off of something in the column. Brake lights, you may think a switch on the pedal.

the brake lights do work with that switch but when you have the kind of tail lights where a turn signal light shares the same bulb as a brake light, the brake light is cancelled for the turn signal by running through the multi function switch inside the column.
The third brake light does not blink so its not on that same circuit.

Oct 07, 2011 | 1990 Mercury Cougar

1 Answer

Seems that the hazard switch nalfucntion and no


Replace the multi-function switch in the steering column. The 3rd brake light is powered directly off the brake switch while the regular brake lights are wired thru the turn signal switch. Common problem

Jul 20, 2010 | 2001 Chevrolet Blazer

1 Answer

How do I change the turn signal switch?


the turn sigal switch is in the multi function switch system. you will have to pull the steering colum apart to get to it. first pull the bottom part of the colum shell and see if it will sneak out that way with out complete dissasembly.

May 17, 2010 | 1988 Chevrolet Silverado 2500

2 Answers

Have a 99 suburban 4x4 , all three back brake lights do not wrk


I was having the exact same problem as my brake switch was fine on my 95 suburban. However upon further inspection the problem was very simple i felt really dumb once i found this: the wire harness that comes away from the switch witch is a bundle of white wires that comes down and across the under side of the steering column had 2 damaged wires upon repairing this i have had no problems since then feel free to email me on this problem at captainchicken08@hotmail.com as i will do my best to help u out. But the problem is most likely a wire short out, or damaged wires for the normally open circuitfor your brake switch.

Apr 08, 2010 | 1999 Chevrolet Suburban

1 Answer

Wiring in back brake light not working


Hello,
If you are driving a S10 Blazer you may have trouble with the turn signal switch also known as the multi function switch. this switch feeds the rear from the brake switch. some times it will work if you fiddle with the hazzard button.

Roy

Nov 07, 2009 | 1999 GMC Jimmy

1 Answer

I lost my head lights, dome light, horn door


sounds like you have a bad ground somewhere. Check every ground strap that you can find, make sure it's tight, and not corroded, etc. Sounds like the accessories are trying to find a ground, and going through the brake light to do so, thus burning out from too much current.

Oct 20, 2009 | 2000 Chevrolet Silverado

2 Answers

1999 chev blazer 4x4 system


I have a 1999 chevy blazer that stuck in 4 wheel drive. How do you get it out.

Nov 23, 2008 | 1999 Chevrolet Blazer

1 Answer

1997 Chev Blazer, turn signals and brake light won't operate. We have check the fuses and they're fine. What's next??


the directional switch could be faulty,,as it controls brake light function also...jently lift up on it and use it ,,also use brake ,,and have some one ckeck the rear,,the switch wares inside itself..

Aug 03, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

626 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...