Question about Land Rover Discovery

1 Answer

Hello my 97 discovery se7 check ingine light came on i did a scan with my OBD2. THIS IS THE FREEZE FRANE. TROUB CODE IS P0441...FUEL SYS1..N/A.FUEL SYS2..N/A..CALC LOAD(%)..36.8..COOLANT(*F)..212..ST FTRM1(%)..-2.3..LT FTRM1(%)..3.8..LT FTRM2(%)..3.1..LT FTRM2(%)..3.8..ENGINE(RPM)..697.. CAN SOMEBODY EXPLAIN THIS TO ME?

Posted by on



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Land Rover Master
  • 79,865 Answers

What does that mean? This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); on Facebook Symptoms Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes A code P0441 could mean one or more of the following has happened:

  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM

Posted on May 12, 2010

  • 1 more comment 
  • luis a padilla
    luis a padilla May 13, 2010

    ok i will check and will get back to you.thank you very much.

  • yadayada
    yadayada May 13, 2010

    I feel I have supplied all the possible solutions short of having "hands On" if this has been helpful please rate my solutions and suggestions as '"HELPFUL" this is how i get compensated for my time to look this stuff up for u. Thanks

  • yadayada
    yadayada Jul 22, 2010

    please rate the help for fixya. it will ask u if i was helpful



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

97 dodge ram1500 5.9 Between 65 and 75mph truck makes a violent like shudder. Rpms stop about200 and check engine light comes on with code p0441. I know what the code is but no idea where too start. And...

code p0441 refers to evaporative emission (EVAP) system--incorrect flow detected== causes--hose connections---intake leak==EVAP canister purge valve
I would start at the purge valve because if the tank is not venting properly there will be either a pressure build up which will over fuel the engine ( too rich) or the fuel pressure will be too low (vacuum in the tank not allowing the pump to keep pressure up) which will result in random misfires.

Feb 09, 2015 | Dodge Cars & Trucks

2 Answers

P0441 4runner check engine light

Google the Code

OBD2 Code PO441

Mar 27, 2013 | 2004 Toyota 4Runner

2 Answers

2004 jeep liberty engine light came on while driving

you have to have a diagnostic done to pin poit the code that mad the light come on [ obd2 scanner will read the ecu the ingine brain and tell you what has faild or not working properly hope this will help.

Nov 02, 2012 | Cars & Trucks

1 Answer

97 land rover discovery reset service engine light

You will need a OBDII / OBD2 reader to rest code.
A low cost unit can be pick up at Harbor Freight.
Link is HERE

Jul 30, 2011 | 1998 Ford Windstar

1 Answer

I have a 2003 dodge ram 1500 4x4 pu and have a p0441 code. i replaced the fuel cap but still no results.

On a Dodge a lot of times this light comes on because you are putting gas in the car or truck with it running, have someone with a OBD2 box clear the code and try this, when you open the gas cap with it running it sucks air and sets off the light due to a purge in the system. I hope this helps

Oct 07, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

Had OBD2 codes P0441 & P0446 on my 1999 Toyota Corolla. Replaced the VSV CHARCOAL EVAPORATORE, disconnected the battery, check engine light went out. came back on this am, took the car to advanced auto...

According to my 2002 Toyota Tundra manual (and it may be different for your car) P0125 is as follows:
Insufficient Coolant Temperature
for Closed Loop Fuel Control

This would seem unrelated to your original problem.

Aug 22, 2010 | 1999 Toyota Corolla

2 Answers

Diagnostic code for land rover discovery 2 se7 p1590 whats it mean ?

Code P1590 is a rough road/ABS fault that normally will also show up when the ABS is having problem with the lights coming on and off or on all the way. Only indicating the the 3 Amigos are on or come on go. Fix you brakes and then you can clear the code.

It can be clear with a proper scanner and is not being caused by any other ABS part.

Check the for other details.

Hope this help (remember rated).

Mar 23, 2010 | 2004 Land Rover Discovery

1 Answer

Error code p0441 on toyota rav4 97

The code indicates a leak in the evaporative system. 90% of the time it is a faulty gas cap.

Feb 25, 2010 | 1997 Toyota RAV4

1 Answer

Land Rover down. What should I do to fix it?

does your truck make any noise when u r trying to start it
if does its your starter take of and take to auto zone they'll test it for free of charge

Sep 29, 2009 | Land Rover Cars & Trucks

1 Answer

P1410, P0441 & P0773 codes in '97 Toyota Camry

P1410 - Fuel Tank Pressure System
P0441 - Evaporative Emission Control System Incorrect Purge Flow
P0773 - Shift Solenoid Electrical
P0446 - EVAP Vent Solenoid Valve Control System

Ok, above are the codes listed on your description and there respective definitions. the P0441 and the P0446, basically run parallel and they mean the same thing. Its concerning the disposal of fuel fume waste that is burned in the EVAP canister during the EVAP process. the EVAP vent solenoid valve will have to be replaced.

The P1410 can be resolved be replacing the fuel pressure regulator which is part of the fuel pump assembly. I would also make sure the gas cap is correctly screwed on and its tight and mot lose.

The P0773 is quite different than the others. this concerns the solenoid that is located in the transmission pan. the scan has detected a malfunctioning solenoid that may ****** the shifting cycle of your transmission.

The EVAP situation will fail the emission's test if not fixed but, this shift solenoid issue, although not an emission's issue, should be check and fix soon.

Please rate and god bless:)

Apr 17, 2009 | 1999 Lexus ES 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79865 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides