Question about 1989 Ford Bronco

1 Answer

How do i put the start ignition switch in a 1989 ford bronco? it looks like a 2 seperate prong thing with 2 metal whole at the other end for screws..im guessing it goes in the dash or some thing next to the steering wheel

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Hi, although i havnt worked on this particular car, they're pretty much the same throughout. you'll first have to take off the shroud behind the steering wheel which surrounds the ignition barrel, there should be screws/torx underneath which secure this. once removed you should be able to see the ignition barrel and a small retaining screw/s holding it into the frame. undo these. turn the key two clicks i think, just before the car starts. underneath the barrel you will notice two little spring loaded pins which you have to push up with a screwdriver so you can wiggle the barrel out. next just unclip the electrical connections, pull them through one at a time and the barrel should slide free. if you mean youve lost the keys and want to replace the barrel im not sure! hope this helps mate, Rob.

Posted on May 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 ford bronco 2 ignition problems maybe


It could have a weak or failing ignition coil. The other thing I can think to look for would be an exhaust restriction.. (clogged catalytic converter)

What about the fuel filter?? was it replaced?

Jan 30, 2013 | 1989 Ford Bronco II

1 Answer

1989 ford bronco II xlt running absolutely fine parked vechicle for an hour now it will not start but appears to want to turn over but won't


hard starting on hot engines is caused by just 2 things:

1. carbons in starter needs to be replaced.
2. ignition timing is overly advanced. timing should be recalibrated by your mechanic.

Aug 05, 2011 | 1989 Ford Bronco

2 Answers

1989 Bronco: 89 ford bronco i put a new starter new battery new...


Check the battery cables for corrosion near the battery terminal end. Sometimes it builds up under the rubber insulation. I would check the ground wire that runs from the battery to the engine block.

May 16, 2010 | 1989 Ford Bronco

1 Answer

How do you remove ignition switch on 1989 Ford bronco.


easiest way is to remove fuse panel cover, there are 2 9/16 bolts that hold the sterring coloum to the dash, remove them. coloum will drop down and allow easy access to the ignition switch. disconnect wire plug ( already having the battery disconnected of course) remove 2 nuts that secure it on to the colum and do reversal for install.

Mar 09, 2010 | 1989 Ford Bronco

1 Answer

My 1989 ford bronco will not start by the key you can jumper the selanoid an it will start


The ignition switch is bad,if the neutral safety switch is o k.

Jan 31, 2010 | 1989 Ford Bronco

1 Answer

I have a 1994 ford bronco with a 5.8 351w. when ignition is turned to accessories the fuel pump will come on for 2-3 sweconds then go off,but after a few minutes it will come on and stay on. when the...


Take your Bronco to an Autozone or Oreillys for a free scan. Offhand a new ignition switch would seem like a good idea, because the fuelpump should not be working in the ACC position.
If a new ignition switch does not help the fuelpump problem the pump is wired to an accessory. You need to look up the fuse info in an owners manual.

Dec 01, 2009 | 1989 Ford F 150

2 Answers

Which is the power wire for the ignition of a 1989 Ford Bronco?


check starter module / relay located inside main fuse box in engine compartment.

Aug 24, 2009 | 1989 Ford Bronco

1 Answer

'88 Ford Bronco II, 2.9L Hp fuel pump won't activate 1st thing in the morn. Have new fuel pump, fuel pump relay,ignition switch. I turn key on & off a few times...then pump activates. everything runs...


sounds like it could be the relay. also this one has 2 pumps I think, one in the tank LP and one on the rail just under the driver. 2 relays also one for each.

Jul 02, 2009 | 1989 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...