Question about 2000 GMC Jimmy

1 Answer

WHAT ARE THE TORQUE SPECS FOR A CRUSH SLEEVE ON A 2000 GMC JIMMY

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

There is no spec for that. the sleeve must be compressed until you have the correct pinion bearing preload. The pinion must take 3-5 inch pounds of torque to spin it.

Posted on May 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

What are the torque specs for ball joints on 2000 gmc jimmy


Upper ball joint knuckle nut 60 ft lbs, lower ball joint knuckle nut 80 ft lbs....mounting nuts and bolts 17 ft lbs

Jul 12, 2014 | 1996 GMC Jimmy

1 Answer

Im replacing a rear bearing and need to know the tork pressure required


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pinion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to acquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Jun 14, 2011 | Mitsubishi Mirage Cars & Trucks

1 Answer

How to set the crush sleave on a pinion. how to assemble a 1 ton rear end.


The crush sleeve is a one time use. You put in a new one, and torque the pinion to spec, and the sleeve crushes during this process.

Oct 03, 2010 | Chevrolet 3500 Cars & Trucks

1 Answer

What is the pinion nut torque when installing new bearings and crush sleeve


i am not aware of a specific torque spec , you have to crush the sleeve until the end play of the pinion measured with a dial indicator matches the proper spec wich should have come with the installation guide

Aug 10, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

I need the torque specs and torque sequence for my 1997 GMC Jimmy


if you donot have a shop manual go to library reference section and copy info from the professional motor manual under engine specs.

Apr 25, 2010 | 1997 GMC Jimmy

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

Not finding what you are looking for?
2000 GMC Jimmy Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...