Question about Dodge Neon

1 Answer

2001 Dodge Neon 2.0L I can't get the left driver's CV axel out of the transmission. I need to change the leaky seals.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 468 Answers

The CV shaft is just held in with spring clips; it should pop right out if you apply the right prying force to it. If you haven't freed the drive axle end yet, it may not compress enough to let it come out of the transmission; you should always take the hub end loose first, then the other end should pop out. The ones that are exceptionally stubborn, you may pry out on it, and hit the opposite side with a rubber mallet, and that's the most it should require. Be prepared to catch the transmission fluid that will leak out. If you have further questions, please post a comment, and I will check up on it and answer.

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace right front axel seal 2001 pathfinder


Hi,if you are talking about the drive shaft cv boot,there is a vidio on you tube showing how to change the drive shaft same perseger,hope this is helpfull,all the best,its a easy fix.

Oct 03, 2015 | 2001 Nissan Pathfinder

1 Answer

How to remove the front left axel shaft on a 1993 buick park ave.


Basically, jack up the vehicle and support it on jack stands, remove the nut on the end of the axle, outer tie rod end and ball joint. Split the tie rod end and ball joint from the spindle assembly. Gently tap the end of the axle to loosen from the wheel bearing assembly. Once loose pull the spindle assembly outward while pushing in on the end of the axle. Once the axle is free from the spindle housing. Will need to apply gentle pressure on each side on the inside CV joint to get the axle to release from the transmission. There is usually a "C" snap clip on the end of the axle in the transmission which may make it a little stubborn to get out. Be sure to not damage the seal where the axle goes into the transmission or you will have a leak

Oct 17, 2014 | 1993 Buick Park Avenue

1 Answer

Remove cv axel on 01 isuzu trooper


You must remove the axle from the transmission in a straight out line from the case of the transmission in a quick and very hard snapping motion, a large heavy cast iron pipe wrench works well, but remember the axle can't be at an angle, it must be straight out within a few degrees.

Apr 27, 2012 | 2001 Isuzu Trooper

1 Answer

I have a 1988 dodge aires i have been hearing a clicking noise when turn the wheel on the drivers side i was told it was the cv axel im not sure if it is the cv axel how do i replace it


clicking is a sure way to tell if the cv joints are bad,, you should replace them both if your going to do it,, since its only a matter of time before the other one goes out, to replace them your going to have to jack it up, remove the tires, brakes, unbolt the cv joint hold downs from the front end,, and slide them out of the transmission,, it sounds easy , but they can be hard to do, and time consuming, be sure not to mess with the steering arms if possible, that way your alignment will be the same as it was. here is a video of the wheel bearing replacement, but it will also show you what you need to remove to change the axle , ( which he has set off to the side ) http://www.youtube.com/user/scottykilmer#p/search/0/197yHCBg9JE

Sep 08, 2011 | 1988 Dodge Aries

1 Answer

I'am trying to take the transaxle out of the transmission to fix an oil leak


Remove the wheel cover and loosen the drive axel hub nut. loosen the the wheel lug nuts raise the vehicle and support it well. NOTE: you will have to be working under the car be very careful. remove the drive axel hub nut. To prevent the hub from turning, insert a screwdriver thru the brake caliper and into one of the cooling slots on the rotor. remove the control arm-to-steering knuckle. Check for the ABS sensor and remove it out of your way. Separate the drive axel from the hub. If stuck remove the brake caliper and rotor. Push the axel out of the hub with a puller or you can use a good solid broom handle and drive it out. If you are removing the right side axel you will need a slide hammer and adaptor to separate the axel from the trans. If you are removing the left side, carefully pry the axel out of the trans. with a large pry-bar positioned between the inner CV joint and the trans. case. Use the subframe as a pivot point. Hold the CV joints so they do not separate inside the rubber if going to reuse them. Lubricate the new seal with multi-purpose grease before you install it.

May 05, 2010 | 2001 Chevrolet Impala

1 Answer

How do you change a cv joint on a 1992 dodge caravan? The right cv joint is out. Do we need to replace the right axel or can we just change the cv joint?


You need to replace the whole right side axle shaft. Take the ball-joint loose and the axle nut. Pull the shaft from the hub assembly and then pull it from the transmission

Mar 28, 2010 | Dodge Caravan Cars & Trucks

1 Answer

Transaxel leaks transmission fluid


was the seal put in correctly. there is a certain way that a seal must be installed. generally i like to bake sure that there are no burrs on the shaft that slides through the seal. also the rubber part of the seal is usualy dry and they should have given you seal grease to soften it up before installation. did you use a seal driver to install the seal? trying to just tap it in with just a hammer will usually damage it and then it will leak. double check to make sure it was the right seal it's been known to happen that you go and buy a seal and you get home and it's the wrong one. i'm sure the problem is a a mis installed seal. unfortunately when you remove the seal you will not be able to reuse it due to the damage . you will have to purchase another one. hope this helps. please rate this solution....thanks

Aug 31, 2008 | Hyundai Motor 1996 Elantra

2 Answers

Cv boot replacement need diegram


I am tryijng to change a cv boot on a 2001 dodge neon. I cannot seperate the knuckle to change boots? I need help

Aug 03, 2008 | Chevrolet Metro Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...