Question about 1992 Honda Accord

1 Answer

Very hard to shift , clutch pedal goes all the way to the floor

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 236 Answers

Its worn, try some lucas transmission fluid it works

Posted on May 12, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mcalkins3
  • 123 Answers

SOURCE: Clutch pedal goes to the floor, then after pulling it up there is pressure...

There is either air in the system or a leak in the clutch slave cylinder. Check your fluid make sure it is full and the cap is tight.

Posted on Sep 18, 2008

  • 119 Answers

SOURCE: Clutch pedal goes to the floor(new clutch installed 2 wks ago)

that cable fited one side to cluch pedel and ather side fited gear box side where palte which is relecing clutch bearing. dont forget to adjust.

Posted on Dec 01, 2008

  • 22 Answers

SOURCE: nissan clutch problem

If your not able to shift into any gear that means your clutch is not engage/disengaging. Check for fluid leaks, you said topped off and fluid levels were low? It sounds like you have a Slave cylinder or master cylinder leak, if its leaking its bet to replace both.

Posted on Apr 27, 2009

  • 4088 Answers

SOURCE: no pressure clutch pedal goes straight to the floor 1988 holden r

If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Posted on Aug 11, 2009

  • 1 Answer

SOURCE: 1998 Hyundai Accent clutch pedal travel

its real hard to shift my accent in and out of all gears especially reverse the clutch pedal is right at the floor when i checked the fluid it was empty.it also makes a clanging noise going into reverse any ideas before i change the clutch?

Posted on Aug 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust the clutch on a 1999 Ford escort ZX2


The clutch is not adjustable it is fully hydraulic. That means it is self adjusting, if the clutch pedal engages high on the pedal and the clutch is hard to push you need a new clutch plate and pressure plate.

Mar 18, 2017 | 1999 Ford Escort

1 Answer

My clutch pedal goes all the way to the floor . Could this cause decrease in power


A clutch pedal normally does go all the way to the floor. If you can shift gear without a crunch, it is disengaging OK.

The loss of power could mean the clutch plate is worn and is slipping when engaged. There is a crude test for this. Start the engine and idle it. Apply the footbrake firmly, depress the clutch and put the gearbox in 3rd. Let the clutch out slowly. If the engine does not immediately stall, the clutch needs replacing.
.

Nov 26, 2015 | Cars & Trucks

1 Answer

My clutch goes all the way to the floor I have a standard Camaro 96 3.8


clutch pedals are suposed to go all the way to the floor , you sure you dont mean brake pedal (cus thats bad ! ) clutches should travel all the way to floor and release the "grab" of the engine about 2/3 down , this way they are more smoothly allowing shifting thru the gears and not jerking as you shift thru the gears , if clutch pedal does not start to "grab" the engines power by 2/3 off the floor and fully "grab"its power all the way up(slipping) ,and you have a hydraulic clutch (96's do) then the clutch disk may require replacement or there is a oil leak in the clutch/master/slave cylinder , look for small oil leaks from under car in area of foot pedals
clutches should be replaced as an assembly that includes , disk ,pressure plate, throwout bearing , with engine side clutch plate magnafluxed for heat cracks and any hydraulic oil leaks replaced or repaired

Mar 12, 2015 | 1996 Chevrolet Camaro

1 Answer

My clutch pedal is not working. falls right to the floor. have to drive by hard-shifting. in my '88 audi 90 quattro


You have a leak and will need to replace the clutch master and slave cylinders.

Jun 11, 2012 | Cars & Trucks

1 Answer

If i dont pump the clutch a few times it is very hard to shift and the pedal goes clear to the floor until i pump it a couple of times


It is likely you have drawn air into the system. Check the clutch reservoir and refill if needed. Use DOT 3 or 4 brake fluid. Bleed the system to restore clutch pedal. Check the clutch slave cylinder for leaks. If leaking, the slave cylinder will need to be replaced and the system bled again. Please let me know if you have questions.

Dec 18, 2010 | 2000 Kia Sportage

2 Answers

94 isuzu rodeo clutch at the floor barely hanging on


had a recent same problem. would push the clutch all the way to floor and it still would only partially disengage causing hard shifting and forcing thru all gears. solution: underneath dash on drivers side is the clutch pedal adjustment rod. u will h ave to loosen the lock nut and then readjust the pedal. you will want the pedal to come closer to the driver (out) making the stroke on the pedal longer. now mine shifts easily. hopes this helps. bcamp4@tampabay.rr.com

Jul 13, 2009 | 1992 Isuzu Rodeo

3 Answers

1998 Hyundai Accent clutch pedal travel


dear friend-you can bleed the clutch.im am sure this will solve you problem

Jun 30, 2009 | Hyundai Motor 1998 Accent

1 Answer

1988 Nissan 300zx shifts real hard or not at all


you may have a weak clutch master cylinder

May 06, 2009 | 1987 Nissan 300ZX

1 Answer

Clutch pedal suddenly goes to the floor, no longer [dis]engaging the clutch


I found that having a wood stick on the clutch pedal down to the floor all night (the other end of the stick held by the seat. oh yeah !!! ) would help to ease shifting for the first hour the next morning, then it would come back stiff and hard to engage in gear.

Aug 07, 2008 | 2007 Mazda B4000

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...