Question about 2004 Pontiac Grand Am

Open Question

Need repair diagram of 2004 pontiac grand am wiper motor/ transmission & wiper arm connections. How to remove push-pin retainers without damage ,remove cowl air inlet cover , repair or reattach arm on driver-side wiper (that has loosened & fallen away from motor),

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 97 nissan sentra windshield wiper linkage arm disconnected

Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Posted on Sep 14, 2008

Ad
  • 2 Answers

SOURCE: Windshield wiper arm on passenger side won't move.

tighten the nut under the cap, of the wiper

Posted on Dec 09, 2008

c17hydro
  • 2984 Answers

SOURCE: removal of wiper arm

WINDSHIELD WIPERS AND WASHERS
Windshield Wiper Blade and Arm
REMOVAL & INSTALLATION

  1. Place the wipers are in the PARK position, then turn the ignition OFF.
  2. Disconnect the negative battery cable.
Lift up the wiper arm pivot nut cover . . .

It's plastic and just pops up and you slip it off. Next, remove the nut. Once you remove the nut, mark the arm and the shaft or top of the mounting area so you know where to place the arm back on the splines. Then, you use a tool similar to a battery clamp remover and pop the arm off. Installation is in reverse order...just remember to align the splines to the arm.


Posted on Apr 01, 2009

StormStrikes
  • 104 Answers

SOURCE: I need a wiring diagram for my 2000 pontiac grand prix

I own a 2001 Pontiac Grand Prix GTP and may be able to help you out if you let me know what specifically you are looking for.

Posted on Jan 02, 2009

  • 14036 Answers

SOURCE: 2004 Pontiac Grand-Am

you need the manual that come with car . go to dealership they can get you one.its probably not much.

Posted on Apr 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Arm that connects the driver side windshield wiper arm to the wiper motor has disconnected & I don't know how to get it back on?


Had the exact same problem. You'll need to replace the entire linkage or "transmission". Do your research on dealers for the parts. They will mark these up almost 80% if you are not careful. The part should not cost more than $100. There are no repair kits for this particular linkage system. Thank you General Motors. Also finding these at junkyards is tricky. Even though the 04 Grand Am shares a lot of parts with other GM cars, this is not one of them and these are some of the first parts scrounged when the cars come in.

Jun 21, 2012 | 2004 Pontiac Grand Am

1 Answer

I need to remove the windshield wiper arm to get to the wiper transmission. I took the bolt off, but the arm wont come off. How does it come off?


After taking the bolt off raise the wiper up and while holding it up with one hand push down on the wiper arm near where you took the bolt off it should break free. Good luck.

Mar 11, 2011 | 2004 Pontiac Grand Am

1 Answer

How to replace a Wiper motor.


Remove two push on caps on wiper arms. Remove nuts and wiper arms, disconnect washer hoses. Remove "push in" plastic retainers on plastic cowl grille and remove grille. Disconnect electrical plug on motor. Remove 3 bolts securing wiper transmission/motor. Lift out assembly. Remove motor from transmission - 2 torx screws and nut on motor shaft @ trans link. Note position of trans link on motor shaft. Reverse all to reinstall.

Dec 05, 2010 | 2004 Chevrolet Cavalier

2 Answers

I have one wiper that does not work the other stops in the middle of the windshield how can i fix them


The motor could be bad, but it's likely that the ball joint connections under the hood area under the cowl have become disconnected for the one windshield wiper arm.

The connection of the arm that moves should be checked for being at the correct angle for parking.
Removal & Installation 2000-03 Wiper Motor and Bushing Replacement L4-2.2L (Vin F) & V6-3.0L (Vin R) To Remove:
sat_car_22_fw-wpr_arm_xp.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section
  2. Remove the wiper arm finish caps
  3. Mark both wiper arm positions on the windshield by using a wax pencil or tape
  4. Remove or disconnect the following:
    • Wiper arm retaining nuts and washers
    • Wiper arms
    • Weather-strip at rear of hood sat_car_22_f_wshd_wthr-strp.gif

      sat_car_22_f_wshd_gril_nts.gif

    • Grill nuts from base of wiper arm shaft
    • Grill
    • Electrical harness connector from the wiper motor
    • Wiper motor retaining bolts
    • Wiper motor assembly from plenum area
    sat_car_22_f_wpr-mtr_asy.gif

    sat_car_19_wpr_mdl_rmv.gif

  5. If replacing wiper module bushings remove the steel bushing first then the rubber grommet
  6. Remove the wiper motor from the transmission assembly
To Install:
  1. Install or connect the following:
    • Wiper motor to transmission assembly NOTE: If the wiper module bushings were replaced install the rubber grommet first then the steel bushing.
    • Wiper motor to plenum area
    • Wiper motor retaining bolts; torque to 44 lb-in. (5 Nm)
    • Electrical harness connector to the wiper motor
    • Weather-strip at the rear of hood
    • Grill
    • Grill nuts to the base of the wiper arm shaft
  2. Install the wiper arm assemblies at the marks made during removal or at the PARK position if a new wiper motor is installed
  3. Install the wiper arm retaining washers and nuts; torque to 9 lb-ft. (12 Nm)
  4. Install the wiper arm finish caps
  5. Verify correct wiper system operation
prev.gif next.gif

Oct 05, 2010 | 2001 Saturn L-Series

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis


1992-98 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle


ffed3a6.jpg



Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Aug 02, 2010 | 1992 Mercury Grand Marquis

1 Answer

2004 Pontiac Grand Prix....Wipers are moving slowly


How to fix slow wipers on 2005 Grand prix
    -Remove black plastic caps on the wiper towers (end of wiper arm)
    -Undo nuts (13mm)
    -Make note of the wiper arms positions when in park so they can be reinstalled in the same spot. Also make note of the routing of the washer supply lines so you can reinstall them in the same position. Use a puller and pull off wiper arms. I did not have a puller but used a small c-clamp, jammed one end under the wiper arm and screwed the clamp into the wiper post (be careful with the threads, maybe leave the nut on loose until the arms break fee.
    -Move the wiper arms and washer supply line to the top of the engine to be out of the way.
    -Remove the rubber hood weather strip and store out of the way.
    -Remove both sides of the plastic cowl cover, there are 3 expansion clips, use a screw driver or wire cutters to pry out the pin first, then pry out the clip itself using same tools. Move the covers up onto the windshield so they are out of the way.
    -The entire wiper motor/transmission, wiper towers and arms are now exposed
    -Remove the arm from the motor that runs across to the passenger side wiper tower. This will make it much easier to remove the wiper assembly. The arms have a plastic end that snaps over a ball, these can be removed by prying off with a thin pair of pliers.
    -There are 3 bolts (10mm) holding the wiper assembly to the cowl. A 4th attachment point is merely a rubber end that fits into a slot in the cowl. Remove the 3 bolts and pull the wiper assembly from the car. Undo the electrical connection by pulling straight out.
    -In most cases the ball and plastic end of the arms will not be seized. These can each be removed, cleaned, regreased and reassembled. Just push back on with a large pair of pliers.
    -In my situation the driver's side tower and wiper shaft were moving freely. The passenger side was almost seized solid which is what causes the wipers to run real slow.
    -The wiper shaft must be freed up and removed from the tower so that it can be cleaned, greased and reassembled. The hardest part is removing the small C clip at the top of the wiper shaft that holds the shaft in the tower. C clip pliers or other means can be used to remove this clip. Be careful you don't break it or lose it. Once the C clip is removed the shaft can be removed from the tower. I did this by soaking with penetrating oil and tapping it in and out and working it back and forth with large pliers. Again be careful with the threads on the shaft. Put the nut on and use a brass hammer. You cannot hammer real hard as the tower is cast aluminum and may break if hit too hard. By being patient I was able to work the shaft free from the tower, clean both well with emery paper, grease and reassemble.
    -Overall reassembly is merely a reversal of the disassembly, being careful to put everything back in its proper place and order.
    -Leave the arm off running from the motor to the passenger side tower as this will allow the wiper assembly to go back in place much easier. Once the wiper assembly is bolted back in place, snap the arm into place over the ball at the motor after greasing.
    -Before reinstalling the plastic cowl coverings, it is a good time to replace your air conditioning intake filter in the cowl on the passenger side.
    -The above process took me about 3 hours start to finish and is moderate difficulty. Once completed the wipers run and park just like new, and it didn't cost me a dime.

Jun 22, 2010 | 2004 Pontiac Grand Prix

1 Answer

2004 grand prix driver side wind shield wiper going past windshield and now is not in sync with other wiper arm,and still moves past windshield and jams up.


The arm is stripped onto the stud its pressed into which is call a wiper transmission. That part mounts to eack ww blade then to the wiper motor. You need a new transmission and maybe a new wiper are as well

Jan 20, 2010 | 2004 Pontiac Grand Prix

1 Answer

Ford Taurus 1999SE-Windshield wiper motor just hums.How to fix ?


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the wiper arms.
  4. Remove the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to remove.
  5. Remove the cowl vent screens.
  6. Disconnect the electrical connector from the wiper motor and remove the 4 bolts that mount the module assembly to the cowl.
  7. Remove the windshield wiper module from the vehicle.
  8. Rotate the wiper operating arm in a clockwise direction to gain access to the bolt retaining the arm to the motor. WARNING
    Always rotate the wiper operating arm in a clockwise motion or damage to the motor could occur.
  9. Remove the nut retaining the wiper operating arm to the wiper motor.
  10. Remove the three wiper motor-to-wiper module assembly retaining bolts and remove the motor from the vehicle.
To Install:
  1. Position the wiper motor on to the module assembly. Install the three wiper motor-to-wiper module assembly retaining bolts. Tighten the bolts to 115-151 in lbs (13-17 Nm).
  2. Position the wiper operating arm on the wiper motor output shaft. Install the mounting nut and tighten to 22-29 ft-lbs (30-40 Nm).
  3. Position the windshield wiper module onto the cowl. Install the mounting bolts and tighten to 106 in-lbs (12 Nm).
  4. Connect the wiper motor electrical connector.
  5. Position the cowl vent screens onto the inner panels. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels. Turn the retainers 1⁄4 turn counterclockwise to install.
  6. Install the wiper arms.
  7. Connect the battery ground cable.
  8. Adjust wiper arms if necessary.

Here is the picture of the motor....it is the round object in the middle of the picture that looks like a can and has a square block on the end of it.

You have to remove the cowl vent panel....just under the windshield. $64.00 for a new motor.

Oct 01, 2009 | Ford Taurus Cars & Trucks

2 Answers

The wiper arm came off of my 2004 pontiac grand am. how would i put it back on?


If it's the blade arm it's generally always best to replace it new and will come with new fasteners.

If it's the assembly arm itself depending upon how it was broken off you may need to replace assembly the arm from the stem complete with new / serviceable used bracket.

Jul 27, 2009 | 2004 Pontiac Grand Am

1 Answer

Windshield washer doesn't work. I'm looking for the location of motor


Service and Repair
  1. Turn ignition switch to the ACCY position, then set wiper switch to the "PULSE position.
  2. Turn ignition switch off when wiper arms are at bottom and not moving.
  3. Lift wiper blade assembly up from windshield.
  4. Pull out retaining latch with a screwdriver.
  5. Pull wiper arm assembly off transmission driveshaft.
  6. Disconnect battery ground cable.
  7. Disconnect hose from washer hose.
  8. Remove five air inlet panel retainers.
  9. Push washer hose into firewall.
  10. Remove air inlet panel from vehicle.
  11. Using wiper transmission separator tool No. J-39232, or equivalent, remove transmission drive link socket from wiper motor crank arm.
  12. Pull two harness connector retainers out of wiper motor connector.
  13. Disconnect two harness connectors from wiper motor.
  14. Remove wiper motor attaching bolts and stud, then the wiper motor from the vehicle.
  15. Reverse procedure to install.

Dec 10, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
2004 Pontiac Grand Am Logo

Related Topics:

1,166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...