Question about Ford Escape Hybrid

Open Question

NEED HELP ON REMOVING TORQUE CONVERTER BOLTS

NEED HELP ON CHANGING MOTOR ON A 06 FORD ESCAPE HYBRID CAN NOT GET TO TORQUE CONVERTER BOLTS

Posted by on

  • Jonathan Smith May 08, 2017

    Did you ever get a correct answer

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jimmymac725
  • 34 Answers

SOURCE: high idaling , exhause pipes turning orange red under motor, not converter

Sound as though you have a lean burn condition and this is usually caused from a vacuum leak and that is what I would check for first.What engine is in it?
JIM

Posted on Oct 04, 2008

youredone82
  • 426 Answers

SOURCE: Change Oil light came on my 2006 Ford Escape

The change oil light is controlled by the main engine computer which monitors driving conditions and clock hours. Based on this data it suggest an oil change interval. The system, however has no way to know the oil was changed unless you tell it so. In your owners manual there is a procedure to "reset" this process in the engines computer. its normally done by holding a button and turning the ignition key on at the same time. It should be listed under oil change in the owners manual.

Posted on Aug 29, 2009

geaeri95
  • 127 Answers

SOURCE: how do you disconnect engine from transmission?

get the front end up on some jack stands, take the starter out, and you can access torque converter nuts from starter hole. you will need to turn the engine by hand and have someone else hold the engine still while you undo the nuts. Once those nuts are off and every thing else is removed from the transmission (CV shafts, wire connectors, etc) remove the bell housing bolts (5 or 6 I think) and pull (may need to pry with a bar some) the trans away from the engine and let it down gently. I believe (although I don't do much transmission work) that you may need to remove the sub-frame a as well.

Posted on Oct 06, 2009

kirkx
  • 2019 Answers

SOURCE: whats the torque specs on a 2001 ford focus 2.0

You need to buy the manual, because you also need to know the order in which to torque them.
http://www.car-stuff.com/mmparts/ford-focus/repair_manual.html
usually you start at the middle and circle outward.
But they can differ. Some cars you always need to put in new head bolts. Others are done in several stages. This is too critical to take chances on.
If you really can't afford $19 for a manual, go to the library and xerox the pages.

Posted on Feb 09, 2010

  • 432 Answers

SOURCE: engine torque specifications ford escape

Bolts are torque to yield and new ones are recommended.
Stage 1 15ft lbs
Stage 2 30ft lbs
stage 3 additional 90 degrees

Posted on Jul 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a torque converter in a 2000 2.5Lt on Ford ranger 2 wheel drive?


You need to remove the transmission to do this. Remove the inspection cover at the junction of the engine and transmission to get to the bolts to disconnect the torque converter from the drive plate (the part with teeth that the starter engages). Remove the driveshaft, then the transmission. The torque converter will come out with the transmission. Pull the old torque converter from the transmission, and install the new one. Ensure the torque converter goes all the way into the transmission/hydraulic pump. Reinstall the transmission, ensuring that the torque converter is still free to turn during the entire installation process, especially while drawing up the transmission to the engine. Once the transmission is bolted up, reinstall the bolts holding the torque converter to the drive plate. Reinstall the drive shaft and the inspection cover.

If you haven't done any major mechanical work on a car before, seek the help of someone who has. You will need a hoist or a jack and jack stands, and a good set of tools.

Nov 03, 2016 | Ford Cars & Trucks

2 Answers

I'm trying to remove the transmission because it needs to be rebuilt. I cannot locate the bell housing cover however in order to remove the torque converter to drive plate bolts. Can you assist?


There is an inspection plate under the car at the bell housing. Remove the bolts and hand turn the engine over and start removing these bolts you see.

Mar 08, 2016 | Ford Cars & Trucks

1 Answer

Removing transmission, how many bolts connect the transfer case so we can get the transmission out?


6. if your talking bell housing, then 10, plus 3 starter bolts. also 4 torque converter nuts.

Aug 02, 2015 | 2006 Ford Escape

1 Answer

Thermostat location 07 escape hybrid


go to ford escape hybrid fwd forum online they will tell you anything you want to know about your car,adrian.....

Mar 16, 2014 | 2007 Ford Escape Hybrid FWD

1 Answer

Trying to change out motor in a ford taurus 1999 all bolts are out but it will not seperate from transmission


Have you removed the torque converter bolts?If so lift the motor and pry apart

Jun 06, 2010 | 1999 Ford Taurus

1 Answer

How do I change trans fluid on a 2008 escape hybrid


Only 2 ways that I know of....
Easiest: Suction the fluid via the dip stick tube using a drill pump (about 4 bucks at Harbor Freight or on line).
Less Easy: Remove all but one of the transmission pan bolts. With a large container under the pan, loosen the last bolt until you can pry the pan loose.... let the fluid run into the container. When it is empty, retighten that last bolt and then reinsert the removed bolts. The pan gasket should not leak when new fluid is poured into the dip stick tube (check it after about a quart is added... and snug the bolts either side of any leak).

Oct 06, 2009 | 2008 Ford Escape

2 Answers

Oil & filter change


If there is a Auto Zone around your area, you can get the oil and filter there with the step by step  instructions needed to get the job gone. There is a oil filter wrench for you to buy to remove the old oil filter, buy the oil filter cup that attaches to the ratchet, the other wrenches tend to crush the filters. Keep me posted be glad to answer any questions and give you instructions to the oil change procedure if Auto ZOne could not help you or there is not one around you. 

Jul 01, 2009 | 2007 Ford Escape Hybrid FWD

2 Answers

The engine needs replaced and need to know if the transmission will need to be dropped to do so


no, Because the transmission is underneath your motor. now if you were changing your transmission you would have to pull out the motor then hoist the transmission out.

May 04, 2009 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...