Question about Cars & Trucks

1 Answer

Drove over something and ripped wires in front left of car- need the wires put back together

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 652 Answers

You may need to strip the wires and solder them back together, you should reroute the wires to where they will not do this again. Make sure to splice the wires well and wrap them with electrical tape. Also make sure you use the right gauge wire, 12 gauge or 14.

Posted on May 12, 2010

  • 2 more comments 
  • woodzowl307 May 12, 2010

    wire soldering













  • woodzowl307 May 12, 2010

    watch

  • woodzowl307 May 12, 2010

    http://www.youtube.com/watch?v=1ZjdiRxr0...

  • woodzowl307 May 12, 2010



    You-Tube video "1ZjdRxr0- movie" value="http://www.youtube.com/v/1ZjdiRxr0OM">watchOM" placeholder

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changed transmission fluid on crv now car wont start


might be that you accidentally disconnected the crank sensor close to the transmission, this gives a no start condition without a check engine light on most cars...

Apr 19, 2014 | 2005 Honda CR-V

1 Answer

Fuse #11 Keeps blowing


Start looking at the alternator replacement... I would go directly back to the shop that performed the work..ask nicely, then demand, then CALL THE BBB... they did something..left a wire loose, (not tight).. something.. Remember - it started the moment you drove off their lot!!!

Aug 29, 2017 | 2001 Ford Explorer Sport

1 Answer

Tire moves front to back


The bushings in the a-arms are shot. Replace the bushings.
murf427

Aug 02, 2012 | 1999 Volkswagen Jetta

2 Answers

2006 BMW F650GS


i would look to see if it is like efi on a car there must be a way to pull codes from the computer on it

Jul 25, 2012 | Cars & Trucks

1 Answer

The car steering wheel would vibrate and the entire care would vibrate. Then go away. Drove about 200 miles, started again. Then stopped. Pulled over twice eveything looked okay. Got home and the...


the wheel bearings are going out if thay are now starting to heat up you need to replace them. but you can first jack up the front end ( both sides off ground together) get a long( 8' or better) 2 x 4 and place under wheel on ground andput presure on tire up wad and the tie sould move in a good bearing but if tire moves aound like its lose then it needs replaced

Jul 31, 2011 | 2003 Chrysler Town & Country

1 Answer

Replaced transmission now abs light is on.


doing it your self is guessing
autozone and others do the code reading for free
at this point I would be checking the wires and connections as that distance after installing would be about right for a connection not put together properly would fall apart or a harness wire would burn through on the exhaust

May 27, 2017 | Chevrolet Cars & Trucks

1 Answer

I have a 5.2 8cyl Laredo it was not going into reverse...so I had a new transmission put in it..when I got it back it worked but when it drove it stayed in 1st til about 3500 rpm before switching...


It sounds to me like something wasn't done correctly with the rebuild. Most of the newer transmission have shift solenoids in them. Some shops don't replace them. I would give them the benefit of the doubt and take it back and see if they can fix it. Transmissions have a lot of components that all have to work together. Sometimes they can mess with a good mechanic for days.

Nov 09, 2009 | 1997 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...