Question about 2008 Ford Explorer Sport Trac
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The rear timing chain (or "cassette" as it's called in Ford lingo) is the chain that drives bank #1 (passenger side) cam. The front timing chain drives bank #2 (driver side) cam. There is a also a primary "jackshaft" chain that is driven by the crankshaft in order to enable both banks to be driven through a common shaft. The reason for this peculiar layout is because this engine is a "derivative" of the 4.0L OHV V6 engine it replaces. Ford simply installed a dummy shaft in place of where the camshaft used to reside on the original OHV engines. But above all else, the job you describe SHOULD NOT be carried out by anyone unfamiliar with this particular engine. There are NO timing marks on any of the drive sprockets, nor are they key to their corresponding shafts. To time this particular engine requires use of FIVE dedicated Ford/Rotunda tools that hold all relevant parts in proper position. Failing to carry this procedure out correctly, will result in the bending of ALL valves with 100% certainty!!! Therefore, it is best left to a Ford dealer technician to carry out. If you would like more information regarding diagrams, TSBs, and procedures with detailed illustrations, please e-mail me directly with your FULL Yahoo e-mail address so I can attach PDF files. Hope this helps.
Posted on May 18, 2008
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.
Posted on Jul 12, 2009
if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint
Posted on Jul 19, 2009
Tips for a great answer:
Dec 21, 2016 | 2007 Ford Explorer Sport Trac
Jul 31, 2016 | 2007 Ford Explorer Sport Trac
Jan 11, 2016 | 2007 Ford Explorer Sport Trac
Jan 10, 2016 | 2001 Ford Explorer Sport
Jan 28, 2011 | 2005 Ford Explorer Sport Trac
Sep 16, 2010 | 2007 Ford Explorer Sport Trac
Jul 10, 2010 | 2005 Ford Explorer Sport Trac
Jul 15, 2009 | 2001 Ford Explorer Sport Trac
Jul 11, 2009 | 2002 Ford Explorer Sport Trac
230 people viewed this question
Usually answered in minutes!