Question about 2002 Audi A4

1 Answer

Bleeding a4 (b6)cooling system?

Hi. how do you bleed the cooling system on a 2.0litre audi a4. (2002, b6)?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.


    An expert whose answer got voted for 20 times.

  • Expert
  • 138 Answers

Bleeder screw on metal water pipe above inlet manifold. loosen bleeder screw, fill coolant at coolant resivoir untill all air pushed out bleeder.

Posted on May 12, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Change boot lid sensor audi a4

Hi where do I find a water jacket on my audi a4 1.9tdi b6 2002

Feb 14, 2015 | 2004 Audi A4

2 Answers

Hi guys got a Audi a4 b6 2.0 2004 model after changing spark plugs on it and ading feul coz it ran empty the car wont start it idles. For a few seconds with my foot flat on the pedal then she dies what can...

Fuel filter may be clogged, replace. Fuel pump may be failing, replace. Never let your vehicle "run out of gas" as all the residue collected in the bottom of the gas tank, will migrate through the system and create problems.

Aug 22, 2014 | 2004 Audi A4

1 Answer

Problems with audi a4

your caliers are locked on the rotor this is usually caused by air in the brake lines bleed the brakes starting from passenger rear driver rear passenger front then driver front bleed until you have a steady stream of fluid you can buy a one man bleeding kit from you r local auto parts store. i just took care of the same problem on my brother in laws mazda after same repairs!

Jan 17, 2014 | Cars & Trucks

1 Answer

Overflowing coolant from resevoir

your radiator may be blocked too also check that there are no bleed screws on the cooling system air in the system can cause this too check that the top and bottom hoses are getting hot if not there is no flow in the cooling system

Apr 12, 2013 | 1996 Audi A4

1 Answer

Are all the parts on audi a4 b6 the same as Volkswagen passat etc?

No, Other than the frame of the car, and in some models the engine, most of the parts are different.

Mar 31, 2013 | 2002 Audi A4

2 Answers

I have an audi 97 a4 6 sylander and i had to change the metal pipe wich transfer water from reservor to termostat housing do i need to bleed the system after fix and soo wher is the bleeding valve thanks...

you dont have to bleed the water it automatically takes out the air when it runs and the thermostat valve opens check the level again after a run of 5 miles or when the temp is in the middle

remember not to check when the engine is hot

Feb 07, 2011 | 1997 Audi A4

1 Answer

1997 a4 se overheating.i have changed the thermostat and car is still overheating.cold air is coming from the drives perfectly is not coming would i diagnose the problem

Alot of time you have to bleed the cooling system after changing a thermostat it gets an air pocket in it look for a bleeder valve near or on the thermastat housing if so bleed it to get the air out.check the radiator and make sure its full because if you filled it up after changing the thermastat once the thermastat opened after the engine ran awhile well the cooling system needs refilled.

Mar 30, 2010 | 1998 Audi A4

1 Answer

How do i change front brake hose on my 98 audi a4? where is it located?

Its located on the brake caliper and goes up to the brake line,To change just remove the high pressure fitting from both ends [very basic job]Fit the new pipe ,but now you have a new pipe but full of air!.To bleed out the new pipe just open the bleed screw [looks like a grease nipple on the top of the brake caliper]and connect a small piece of hose [must be a tight fit on the bleed screw]with the bleed screw loose and the hose fitted just fit the other end in to a container of brakefluid and press the brake slowly up and down till all the bubbles are gone{dont forget to top up your reservoir before you bleed it!!]as if the reservoir runs dry you will need a special bleeder to bleed the brakes [it requires 2 bar or 30 psi pressure to bleed out the system after the reservoir goes dry]

Mar 08, 2010 | 2004 Audi A4

1 Answer

Looking for procedure to properly bleed an audi A4 1.8T quattro cooling system as no sign of a proper bleed point on any of the heater/cooling hoses/pipework, car overheated today & blew out some...

You didn't say what year the car is or what other diagnostics you've done lately...My guess is the radiator core is plugged...If you want to tackle it yourself, buy a Chiltons repair manual at AutoZone or NAPA stores ($25). I suspect you'll have to order the manual.
Good Luck

Jun 25, 2009 | Audi A4 Cars & Trucks

2 Answers

1997 audi A4 heater blowing cold air

You probably have a leak in your oil cooler. This is causing the oil to bleed into your cooling system causing the "thick brown liquid". This in turn will also cause your engine to over-heat since the cooling system is contaminated.

Feb 25, 2009 | 1997 Audi A4

Not finding what you are looking for?
2002 Audi A4 Logo

1,662 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80339 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides