Question about 1992 Daihatsu Charade

1 Answer

95 charade . where do i find the mark on the

95 charade . where is the mark on the balancer ,to adjust the timing? When you turn the key off it has pre ignition. Thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 972 Answers

You have a leaking fuel injector if it runs after shut off. if its an other than U.S. model with carberator then the idle is set to high or the fuel shutoff solonoid is stuck/leaking.

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the timing chain


2.2L & 2.3L Engines
Except S2000 with 2.2L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the cylinder head (valve) and upper timing belt covers.
  3. Turn the engine to align the timing marks and set cylinder No. 1 to Top Dead Center (TDC). The white mark on the crankshaft sprocket should align with the pointer on the timing belt cover. The words UP embossed on the camshaft sprocket should be aligned in the upward position. The marks on the edge of the sprocket should be aligned with the cylinder head or the back cover upper edge. Once in this position, the engine must NOT be turned or disturbed.
  4. Remove all necessary components for access to the lower timing belt cover, then remove the cover.
  5. There are two belts in this system; the one running to the camshaft sprocket is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer shaft belt or timing balancer belt. Lock the timing belt adjuster in position, by installing one of the lower timing belt cover bolts to the adjuster arm.
  6. Loosen the timing belt and balancer shafts tensioner adjuster nut, do not loosen the nut more than one turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
  7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  8. Remove the balancer belt sprocket from the crankshaft.
  9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
  10. Remove the timing belt by sliding it off the sprockets. Do not crimp or bend the belt; protect it from contact with oil or coolant.
  11. If defective, remove the belt tensioners by performing the following:
    1. Remove the springs from the balancer belt and the timing belt tensioners.
    2. Remove the adjusting nut from the belt tensioners.
    3. Remove the bolt from the balancer belt adjuster lever, and then remove the lever and the tensioner pulley.
    4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
  12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time.
  13. To install:
    1. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and tighten the mounting bolts to 106 inch lbs. (12 Nm).
    2. If the tensioners were removed, perform the following procedures:
      1. Install the timing belt tensioner lever and the tensioner pulley.
      2. Install the balancer belt pulley and adjuster lever.
      3. Install the adjusting nut and the bolt to the balancer belt adjuster lever.
      4. Install the springs to the tensioners.
      5. Install the lockbolt to the timing belt tensioner, then move it its full deflection and tighten the lockbolt.
      6. Move the balancer it's full deflection and tighten the adjusting nut to hold its position.
    3. The pointer on the crankshaft sprocket should be aligned with the pointer on the oil pump; the camshaft sprocket must be aligned so that the wordUP is at the top of the sprocket and the marks on the edge of the sprocket are aligned with the surfaces of the head or the back cover upper edge.
    4. Install the timing belt on the sprockets in the following sequence: crankshaft sprocket, tensioner sprocket, water pump sprocket and camshaft sprocket.
    5. Check the timing marks to be sure that they did not move.
    6. Loosen, then retighten the timing belt adjusting nut; this will apply the proper amount of tension to the timing belt.
    7. Install the timing balancer belt drive sprocket and the lower timing belt cover.
    8. Install the crankshaft pulley and bolt, tighten the bolt to 181 ft. lbs. (245 Nm). Rotate the crankshaft sprocket 5-6 turns to position the timing belt on the sprockets.
    9. Set the No. 1 cylinder to TDC and loosen the timing belt adjusting nut one turn. Turn the crankshaft counterclockwise until the cam sprocket has moved 3 teeth; this creates tension on the timing belt.
    10. Tighten the timing belt adjusting nut.
    11. Set the crankshaft sprocket and the camshaft sprocket to TDC. If the sprockets do not align, remove the belt to realign the marks, then install the belt.
    12. Remove the crankshaft pulley and the lower cover.
    13. With the timing marks aligned, lock the timing belt adjuster in place with one of the lower cover mounting bolts.
    14. Loosen the adjusting nut and ensure the timing balancer belt adjuster moves freely.
    15. Align the rear timing balancer sprocket using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt/rod into the hole and align the 2.9 in. (74mm) mark with the face of the hole. This will hold the shaft in place during installation.
    16. Align the groove on the front balancer shaft sprocket with the pointer on the oil pump.
    17. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the bolt from the maintenance hole and reinstall the bolt and washer.
    18. Install the crankshaft pulley, then turn the crankshaft sprocket 1 turn counterclockwise and tighten the timing belt adjusting nut to 33 ft. lbs. (45 Nm).
    19. Remove the crankshaft pulley and the bolt locking the timing belt adjuster in place.
    20. Install the lower and upper timing belt covers, and all applicable components. When installing the crankshaft pulley, coat the threads and seating face of the pulley bolt with engine oil, then install and tighten the bolt to 181 ft. lbs. (250 Nm).
    21. Install the cylinder head cover gasket cover to the groove of the cylinder head cover. Before installing the gasket thoroughly clean the seal and the groove. Seat the recesses for the camshaft first, then work it into the groove around the outside edges. Be sure the gasket is seated securely in the corners of the recesses.
    22. Apply liquid gasket to the four corners of the recesses of the cylinder head cover gasket. Do not install the parts if 5 minutes or more have elapsed since applying liquid gasket. After assembly, wait at least 20 minutes before filling the engine with oil.
    23. Install the cylinder head (valve) cover and all other applicable components.
b0b9eb99-5646-47c3-bfea-3ed501154864.jpg dc472561-14cf-4143-9a20-b37ba89f57de.jpg

Jul 02, 2014 | 2004 Honda Accord

1 Answer

1990 Daihatsu Charade 1298cc 4-cylinder. Need procedure for cam-timing, with new timing belt.


1990 ,have seen one of these for years ,anyway the procedure is quite simple here ,just unbolt the front cover on the engine ,the put a socket and a big bar on the front pulley nut and then use starter motor to crack this bolt ,fit socket and bar then push /hold it on with a broom handle whilst someone turns key simple ,then with gears exposed use some white paint and mark the gears to the backplate ,then slacken adjuster and change belt ,Now befor you start make sure that your pulley is all one piece and doesnt have three for bolts that hold pulley to the centre of the pulley as if it does then you do not need to undo the centre pulley bolt.

Dec 06, 2010 | 1990 Daihatsu Charade

1 Answer

The Haynes manual I have has TWO pages ripped out I have to replace the timing belt can you help me


from autozone.com:
1990-95 4-Cylinder Accord and 1992-95 Prelude
  1. Disconnect the negative battery cable.
  2. Turn the engine to align the timing marks and set cylinder No. 1 to TDC on the compression stroke. Once in this position, the engine must NOT be turned or disturbed. On DOHC Preludes without VTEC, hold each of the camshafts in the TDC position by inserting 5mm diameter punches into the alignment holes just behind each cam pulley.
  3. Remove the splash shield from below the engine.
  4. Drain the engine coolant. Use a clean container; cap or cover the container and wipe up spillage.
  5. Unplug the electrical connector at the cruise control actuator, then remove the actuator. Don't disconnect the cable; simply move the actuator out of the work area.
  6. Remove the belt from the power steering pump. Remove the mounting bolts for the pump. Without disconnecting the hoses, move the pump out of the way.
  7. Unplug the alternator wiring and connectors; remove the engine wiring harness from the valve cover.
  8. Loosen the adjusting and mounting bolts for the alternator and/or compressor. Remove the drive belt(s).
  9. Remove the valve cover.
  10. Remove the side engine mount support bracket, if equipped.
  11. Remove the upper timing belt cover.
  12. Support the engine with a floor jack on the oil pan (use a cushion between the jack and pan). Tension the jack so that it is just supporting the engine but not lifting it.
  13. Remove the side engine mount.
  14. Remove the dipstick and dipstick tube.
  15. Remove the crankshaft pulley bolt and remove the crankshaft pulley.
This bolt is one of the tightest on the entire car. The pulley must be held in place while the bolt is loosened. One trick is to wrap an old drive belt around the pulley to hold it steady-don't try this with a belt that is to go back on the car; it will be stretched or damaged.
  1. If necessary for additional clearance to remove the lower timing belt cover, remove the two rear bolts from the center beam. Slowly lower the jack and the engine until the clearance is gained.
  2. Remove the rubber seal from around the belt tension adjusting nut (do not loosen the nut). Remove the lower timing belt cover.
  3. On all models except Prelude with VTEC, lock the timing belt adjuster arm in place using one of the lower cover (6 x 1mm) mounting bolts.
88d9a40.gif

Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts
There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.

  1. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
  2. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine.
To install:
  1. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
  2. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
  3. Except Prelude VTEC models:
    1. Temporarily install the crank pulley and bolt.
    2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm).
Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
  1. On Prelude VTEC models:
    1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt.
Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is1/4fl. oz. (8 ml).
  1. Make sure all timing marks are positioned correctly (as described earlier).
  2. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
  3. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely.
aa17346.gif Fig. 13: The balancer shaft must be held in position during timing belt installation
  1. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
  2. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures.
Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
  1. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
  2. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
  3. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990-91 Accords, 37 ft. lbs. (50 Nm) on 1992-95 Accords and 43 ft. lbs. (60 Nm) on 1992-95 Preludes.
  4. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following: 1991-93 Accord: 159 ft. lbs. (220 Nm)
  1. Install the dipstick tube and dipstick.
  2. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
  3. Install the upper belt cover.
  4. Install the side engine mount support bracket if it was removed.
  5. Install the valve cover.
  6. Install the compressor and/or alternator drive belt; adjust the tension.
  7. Route the wiring harness over the valve cover and connect the wiring to the alternator.
  8. Install the power steering pump and install the belt.
  9. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
  10. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
  11. Refill the engine coolant.
  12. Install the splash shield under the engine.
  13. Connect the negative battery cable.
  14. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

Sep 20, 2010 | 1992 Honda Accord

1 Answer

My balance shaft belt broke while I was driving. It stripped some of the teeth off the timing belt and Im pretty sure it jumped time. I need a diagram to show the timing marks and how to get it back in...


see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Sep 20, 2010 | Honda Odyssey Cars & Trucks

            1 Answer

            Hiwich timing mark I used to time the balancer shaft on a 99 honda accord with a 2.3L


            To Install:
            NOTE: Clean balancer belt drive pulley, timing belt pulleys and upper/lower timing cover prior to belt installation.
            honda-03-23-3425.gif

            1. Set timing belt drive pulley to TDC by aligning dimple on pulley with dimple on oil pump. honda-03-23-3426.gif

            2. Set camshaft pulley to TDC so that "UP" mark is at top and grooves align with top of cylinder head. Timing belt installation honda-03-23-3549.gif

            3. Starting with driver pulley, install timing belt in a counterclockwise sequence.
            4. Loosen and ten retighten adjusting nut.
            5. Install balancer belt drive pulley. NOTE: Inspect rubber seal on lower cover and replace as necessary.
            6. Install lower cover.
            7. Install crankshaft pulley and bolt.
            8. Rotate crankshaft pulley counterclockwise several times to seat belt.
            9. Loosen adjusting nut 1 turn.
            10. Rotate crankshaft counterclockwise 3 teeth on camshaft pulley.
            11. Tighten adjusting nut to 33 ft lb (44 Nm). honda-03-23-3542.gif

            12. Turn crankshaft pulley until TDC is achieved. honda-03-23-3426.gif

            13. Ensure that camshaft pulley "UP" mark is at top and grooves align with top of cylinder head.
            14. Remove crankshaft pulley and lower cover.
            15. Rotate crankshaft to TDC again and lock timing belt adjuster arm with a 6 mm timing cover bolt.
            16. Loosen adjuster nut 1 turn and ensure that belt tensioner freely moves.
            17. Push tensioner up and tighten adjusting nut. Balancer shaft alignment honda-03-23-3556.gif

            18. Remove bolt and washer from maintenance hole.
            19. Using a 6 X 100 mm bolt, scribe a mark 2.9 in (74 mm) from end.
            20. Insert bolt into maintenance hole and hole in balancer shaft.
            21. Install bolt up to scribed line. Balancer shaft alignment honda-03-23-3557.gif

            22. Align groove on balancer shaft with pointer on oil pump housing.
            23. Install balancer belt and loosen adjusting nut 1 turn to tension.
            24. Retighten bolt. Balancer shaft alignment honda-03-23-3556.gif

            25. Remove bolt from maintenance hole and install bolt and washer. Tighten to 22 ft lb (29 Nm).
            26. Reinstall crankshaft pulley.
            27. Loosen adjusting nut 1 turn.
            28. Rotate crankshaft pulley counterclockwise 1 turn and tighten adjusting nut.
            29. Remove bolt from timing belt adjuster arm. NOTE: Inspect rubber seal on lower cover and replace as necessary.
            30. Remove crankshaft pulley.
            31. Install lower cover.
            32. Install seal at adjusting nut. NOTE: Crankshaft pulley, bolt and washer must be cleaned prior to installation.
            33. Lubricate crankshaft pulley bolt between head and washer and bolt threads with clean engine oil. honda-03-23-3537.gif

              CAUTION
              Do not use impact wrench to perform following step.
            34. Install crankshaft pulley and tighten bolt using special tools to 181 ft lb (245 Nm).
            35. Install dipstick/tube assembly.
            36. Install upper cover. Tighten bolts to 9 ft lb (12 Nm).
            37. Install cylinder head cover.
            38. Install alternator bracket and alternator.
            39. Install power steering pump belt and alternator belt. Upper bracket installation honda-03-23-3420.gif

            40. Install upper bracket and tighten fasteners in proper numbered sequence.
            41. Install stop.
            42. Install battery and enter radio anti-theft code.
            prev.gif next.gif

            Jul 03, 2010 | Cars & Trucks

            1 Answer

            How do you set the timming on a 95 honda accord


            1990–95 4-Cylinder Accord and 1992–95 Prelude
            1. .
            2. Fig. 10: On all engines except VTEC, the belt adjuster arm must be locked in place using one of the lower cover mounting bolts 86803136.gif
              NOTE: There are two belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shaft and is referred to as the balancer belt or timing balancer belt. Use a piece of chalk or a marker to place an identifying arrow on the belts. The arrow can identify the direction of rotation or the outer edge of the belts. The belts must be reinstalled so it moves in the same direction. Protect the belts from oil, coolant, etc. It's an even better idea to replace the belts at this point.
            3. Loosen the timing belt adjustment nut. Push on the tensioner to relieve tension from the balancer belt, then tighten the nut. Remove the balancer belt.
            4. On all models except Prelude with VTEC, loosen the lockbolt installed earlier and the adjusting nut. Push on the tensioner to release the timing belt, then tighten the nut. Carefully remove the timing belt. On Prelude VTEC models, remove the timing belt from the pulleys, then remove the bolts securing the auto-tensioner. Remove the auto-tensioner from the engine. To install:
            5. Check the position of the timing marks. The timing pointer must be perfectly aligned with the TDC (white mark) on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head. Additionally, the face of the front timing balancer pulley has a mark which must be aligned with the notch on the oil pump body. This pulley is the one to the left crank when viewed from the pulley end.
            6. Fit the timing belt over the pulleys and tensioner. On DOHC engines without VTEC, remove the 5mm pin punches from behind the cam pulleys.
            7. Except Prelude VTEC models:
              1. Temporarily install the crank pulley and bolt.
              2. Loosen the tensioner adjusting nut 1 turn, then tighten it. Rotate the crankshaft counterclockwise until the camshaft pulley has moved 3 teeth to create tension on the belt. Loosen the nut again, then tighten it to 33 ft. lbs. (45 Nm). NOTE: Always rotate the crankshaft counterclockwise when viewed from the pulley end. Rotating it clockwise will cause improper adjustment and possible damage.
              3. Tighten the lockbolt installed earlier to lock the timing belt adjuster arm. Remove the crank pulley.
            8. On Prelude VTEC models:
              1. Hold the auto-tensioner with the maintenance bolt facing up. Loosen and remove the bolt. NOTE: Handle the tensioner carefully so the oil inside does not spill or leak. Replenish with clean engine oil if any does leak. Total capacity is 1⁄4 fl. oz. (8 ml).
              2. Clamp the mounting flange of the tensioner in a vise using a cloth or blocks of wood to protect it. Insert a flat blade screwdriver into the maintenance hole. Place the stopper (tool number 14540-P13-003) or an equivalent clamp on the tensioner, then turn the screwdriver clockwise to compress the bottom. Be careful not to damage the threads or the gasket contact surface.
              3. Install the maintenance bolt on the tensioner with a new gasket. Tighten to 6 ft. lbs. (8 Nm).
              4. Make sure no oil is leaking from around the maintenance bolt, then install the tensioner on the engine. Make sure the stopper stays in place and tighten the bolts to 16 ft. lbs. (22 Nm).
              5. Remove the stopper. Fig. 11: On VTEC engines, the tensioner must be compressed before installing it on the engine 86803137.gif
                Fig. 12: Remove the stopper after installing the tensioner on the engine 86803138.gif

            9. Make sure all timing marks are positioned correctly (as described earlier).
            10. Align the rear timing balancer pulley (to the right of the crank pulley) using a 6x100mm bolt or rod. Mark the bolt or rod at a point 2.913 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the rod into the hole. Align the 74mm mark with the face of the hole. This pin will hold the shaft in place during installation.
            11. Loosen the tensioner adjusting nut and verify that the timing balancer belt adjuster moves freely. Fig. 13: The balancer shaft must be held in position during timing belt installation 86803139.gif

            12. Fit the balancer belt over the pulleys. Remove the bolt or rod from the maintenance hole.
            13. Temporarily install the crank pulley. Rotate the engine one turn counterclockwise, then tighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm). Double check the positions of the timing marks and make sure they still line up. If not remove the belts and repeat the procedures. NOTE: Both belt adjusters are spring-loaded to properly tension the belts. Do not apply any additional pressure to the pulleys or tensioners while performing the adjustment.
            14. Remove the crank pulley. Remove the lockbolt installed earlier on the timing belt adjuster arm. Install the maintenance bolt with a new washer. Tighten it to 22 ft. lbs. (30 Nm).
            15. Install the lower cover, making certain the rubber seals are in place and correctly located. Tighten the retaining bolts to 9 ft. lbs. (12 Nm).
            16. If applicable, raise the lower beam and engine into place. Install the rear bolts for the lower beam. Tighten them to 28 ft. lbs. (39 Nm) on 1990–91 Accords, 37 ft. lbs. (50 Nm) on 1992–95 Accords and 43 ft. lbs. (60 Nm) on 1992–95 Preludes.
            17. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to the following:
              • 1990 Accord: 166 ft. lbs. (230 Nm)
              • 1991–93 Accord: 159 ft. lbs. (220 Nm)
              • 1992–93 Prelude: 159 ft. lbs. (220 Nm)
              • 1994–95 Accord and Prelude: 181 ft. lbs. (245 Nm)
            18. Install the dipstick tube and dipstick.
            19. Install the side engine mount (refer to engine removal and installation for procedures). Remove the jack from under the engine.
            20. Install the upper belt cover.
            21. Install the side engine mount support bracket if it was removed.
            22. Install the valve cover.
            23. Install the compressor and/or alternator drive belt; adjust the tension.
            24. Route the wiring harness over the valve cover and connect the wiring to the alternator.
            25. Install the power steering pump and install the belt.
            26. Reinstall the cruise control actuator. Connect the vacuum hose and the electrical connector.
            27. Double check all installation items, paying particular attention to loose hoses or hanging wires, untightened nuts, poor routing of hoses and wires (too tight or rubbing) and tools left in the engine area.
            28. Refill the engine coolant.
            29. Install the splash shield under the engine.
            30. Connect the negative battery cable.
            31. Start the engine, allowing it to idle. Check for any signs of leakage or any sound of the belts rubbing or binding.

            Jul 18, 2010 | 1995 Honda Accord

            2 Answers

            How do i put timing belt and water pump?


            REMOVAL & INSTALLATION of timing belt: Fig. 1: View of the timing belt cover 91163p64.gif
            Fig. 2: Loosen then timing belt tensioner using a ratchet and short socket 91163p65.gif
            Fig. 3: Matchmark the direction of rotation of the timing belt 91163p67.gif
            Fig. 4: Once loose, pull the belt off the camshaft pulley 91163p71.gif
            1. Disconnect the negative battery cable.
            2. Turn the crankshaft to align the timing belt matchmarks and set cylinder No. 1 to Top Dead Center (TDC) on the compression stroke. Once in this position, the engine must NOT be turned or disturbed.
            3. Remove all necessary components to gain access to the cylinder head and timing belt covers.
            4. Remove the cylinder head and timing belt covers.
            5. There are 2 belts in this system; the one running to the camshaft pulley is the timing belt. The other, shorter one drives the balance shafts and is referred to as the balancer belt or timing balancer belt. Lock the timing belt adjuster in position by installing one of the lower timing belt cover bolts to the adjuster arm.
            6. Loosen the timing belt and balancer shafts tensioner adjuster nut, but do not loosen the nut more than 1 turn. Push the tensioner for the balancer belt away from the belt to relieve the tension. Hold the tensioner and tighten the adjusting nut to hold the tensioner in place.
            7. Carefully remove the balancer belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
            8. Remove the balancer belt drive sprocket from the crankshaft.
            9. Loosen the lockbolt installed to the timing belt adjuster and loosen the adjusting nut. Push the timing belt adjuster to remove the tension on the timing belt, then tighten the adjuster nut.
            10. Remove the timing belt. Do not crimp or bend the belt; protect it from contact with oil or coolant. Slide the belt off the pulleys.
            11. If defective, remove the belt tensioners by performing the following:
              1. Remove the springs from the balancer belt and the timing belt tensioners.
              2. Remove the adjusting nut.
              3. Remove the bolt from the balancer belt adjuster lever, then remove the lever and the tensioner pulley.
              4. Remove the lockbolt from the timing belt tensioner lever, then remove the tensioner pulley and lever from the engine.
            12. This is an excellent time to check or replace the water pump. Even if the timing belt is only being replaced as part of a good maintenance schedule, consider replacing the pump at the same time. To install:
            13. If the water pump is to be replaced, install a new O-ring and make certain it is properly seated. Install the water pump and retaining bolts. Tighten the mounting bolts to 106 inch lbs. (12 Nm).
            14. If the tensioners were removed, perform the following to install them:
              1. Install the timing belt tensioner lever and tensioner pulley. NOTE: The tensioner lever must be properly positioned on its pivot pin located on the oil pump. Be sure that the timing belt lever and tensioner moves freely and does not bind.
              2. Install the lockbolt to the timing belt tensioner, do not tighten the lockbolt at this time.
              3. Install the balancer belt pulley and adjuster lever.
              4. Install the adjusting nut and the bolt to the balancer belt adjuster lever. Do not tighten the adjuster nut or bolt at this time. NOTE: Be sure that the balancer lever and tensioner moves freely and does not bind.
              5. Install the springs to the tensioners.
              6. Move the timing belt tensioner its full deflection and tighten the lockbolt.
              7. Move the balancer its full deflection and tighten the adjusting nut.
            15. The crankshaft timing pointer must be perfectly aligned with the white mark on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head.
            16. Install the timing belt over the pulleys and tensioners.
            17. Loosen the bolt used to lock the timing belt tensioner. Loosen, then tighten the timing belt adjusting nut.
            18. Turn the crankshaft counterclockwise until the cam pulley has moved 3 teeth; this creates tension on the timing belt. Loosen, then tighten the adjusting nut and tighten it to 33 ft. lbs. (45 Nm). Tighten the bolt used to lock the timing belt tensioner.
            19. Realign the timing belt marks, then install the balancer belt drive sprocket on the crankshaft.
            20. Align the front balancer pulley; the face of the front timing balancer pulley has a mark, which must be aligned with the notch on the oil pump body. This pulley is the one at 10 o'clock to the crank pulley when viewed from the pulley end.
            21. Align the rear timing balancer pulley (2 o'clock from the crank pulley) using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt or rod into the hole. Align the 2.9 in. (74mm) mark with the face of the hole. This pin will hold the shaft in place during installation.
            22. Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the pin from the maintenance hole and reinstall the bolt and washer.
            23. Turn the crankshaft 1 full turn, then tighten the adjuster nut to 33 ft. lbs. (45 Nm). Remove the bolt used to lock the timing belt tensioner.
            24. Install the lower cover, ensuring the rubber seals are in place. Install a new seal around the adjusting nut, DO NOT loosen the adjusting nut.
            25. Install the key on the crankshaft and install the crankshaft pulley. Apply oil to the bolt threads and tighten it to 181 ft. lbs. (250 Nm).
            26. Install the upper timing belt cover and all applicable components. When installing the side engine mount, tighten the bolt and nut attaching the mount to the engine to 40 ft. lbs. (55 Nm) and the through-bolt and nut to 47 ft. lbs. (65 Nm).
            27. Connect the negative battery cable.
            ---
            For water pump removal and installation contact me:

            Jul 12, 2010 | 1997 Honda Civic

            1 Answer

            Where are the valve timing marks on a 1997 993cc charade


            Sorry for the severe delay.
            I am personally going back to answer your unanswered question.
            I do not know if you still need the answer, but I am going to answer it in case you still do.

            Click on the following direct Link. It has the Timing Belt Diagrams with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams for use.

            To answer your direct question: (See Diagram 96F14675 on the Link) The Belt Alignment and Align Mating Marks are the keys.
            The Crankshaft "pulley" (actually the Sprocket) has the outer Flange (cover) which needs to be removed to see the Timing Mark.

            Again my apologies...
            Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

            http://www.2carpros.com/car_repair_information/year/1988/make/daihatsu/model/charade/1988_daihatsu_charade_timing_belt_diagram_marks.htm

            Mar 13, 2009 | 1988 Daihatsu Charade

            2 Answers

            Carn't find timing marks where are they


            Have a look on the top of the bell housing for a plastic/rubber cap, lift it off and shine a torch into the hole. The flywheel and timing marks should be visible.

            Jul 19, 2008 | 1988 Daihatsu Charade

            Not finding what you are looking for?
            1992 Daihatsu Charade Logo

            237 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Daihatsu Experts

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            22246 Answers

            yadayada
            yadayada

            Level 3 Expert

            76846 Answers

            Donald DCruz
            Donald DCruz

            Level 3 Expert

            17130 Answers

            Are you a Daihatsu Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...