Question about 2006 Mitsubishi Outlander

1 Answer

Replacing brake lamp in 2006 mitsubishi outlander

I need to replace a brake lamp in a 2006 mitsubishi outlander . I've taken out the two star screws in the lense but I can get no futher

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

Put some tape on a flat screw driver a pry the lense off keep wiggling the lense and it will come off be carefull not to scratch the paint good luck CJ

Posted on May 12, 2010

Testimonial: "Thanks CJ..worked a treat"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the factory longitudinal roof bars on a 2006 Mitsubishi Outlander?;


you need to lift up the black plastic covers with a screwdriver or another flat tool at the front bottom side and split the one in the middle on the top - slide them away -then you should see the screws holding the rack to the rail.
25405094-l2syhiveb5h5n2hnqsepdito-4-0_1.jpg

25405094-l2syhiveb5h5n2hnqsepdito-4-2_0.jpg
25405094-l2syhiveb5h5n2hnqsepdito-4-20.jpg split one side and lift the bar away to see screws

25405094-l2syhiveb5h5n2hnqsepdito-4-27.jpg

Feb 07, 2015 | 2006 Mitsubishi Outlander

1 Answer

Low idle on mitsubishi outlander


this mite be a inlet valve problem

Feb 27, 2014 | 2006 Mitsubishi Outlander

1 Answer

How do you replace the parklights on a 2005 mitsubishi outlander


You have to remove the head light assy from the body,
on almost all vehicles today

Then you can somewhat easily remove the lamp
socket from it & then the lamp/bulb it'self

Have to look for screws or bolts holding it on

May have to remove a few things to get to the
bolts.

You could look on You Tube--- for Video of it
being done

Oct 04, 2012 | 2005 Mitsubishi Outlander

1 Answer

The cruise control in my 2006 Mitsubishi Outlander does not work.


There is a round cruise control count on the left side of the wheel well and it has a cable going into the back replace that

May 07, 2010 | 2006 Mitsubishi Outlander

2 Answers

Rear end noise on 2006 mitsubishi outlander


There is a race bearing on the back side of the rotor. If you haven't replaced it, I would strongly recommend it. You should change those out every time you change your rotors. Most new rotors come with new race bearings, if it did come with a new one (and it isn't shot yet), pull it out and pack it with grease. Wear latex gloves, put a pile of general purpose grease in your hand, and start stuffing the grease into the bearing until it comes out the other side.

May 27, 2009 | 2006 Mitsubishi Outlander

1 Answer

Filler to add oil automatic transmission Mitsubishi Outlander 06


use the dipstick hole, you need a certain funnel. if you cant fiind it let me know.

Mar 07, 2009 | 2006 Mitsubishi Outlander

2 Answers

Mitsubishi outlander overheating for no reason


more than likely the thermostat is bad (not opening ) need more info ..... only when idling ? do the fans kick on ?

Dec 04, 2008 | Mitsubishi Outlander Cars & Trucks

2 Answers

I need to replace a brake light on my 2003 Mitsubishi Outlander. We've removed the two obvious screws but are still facing resistance on the other side of the cover. Should I just pull the unit off? ...


sometimes they would be sideways. the screws just hold them in order not to move and they do have plastics hooks that still hold it tight to the metal housing. slowly slide them sideways and see if they would come off.

tnx 4 using fixya,

drcool

Oct 05, 2008 | 2003 Mitsubishi Outlander

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...