Question about 1991 Nissan Pickup

1 Answer

How do u change a clutch in a 1990 nissan pickup rwd 2wd four cylinder

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,317 Answers

You'll need to remove the driveshaft, and transmission crossmember, and then the gearbox and bellhousing from the motor. The clutch disc is between the flywheel and pressure plate. Remove the pressure plate and remove the clutch. You should get the flywheel resurfaced, especially if there are heat spots on it. Also change the throw-out bearing.

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hot to fix a clutch that goes all the way to the floor


Check your clutch master cylinder's fluid,it's located under hood in right corner,if low or empty,then your slave cylinder is bad and leaking,it's connected to side of transmission.Here's a link. Repair Guides Clutch Clutch Release Cylinder AutoZone com Here's the part. Duralast Clutch Slave Cylinder 12425 1992 Nissan Datsun D21 Truck 2WD 4...

Jan 14, 2014 | 1992 Nissan Pickup

1 Answer

My 1982 nissan pickup manual transmission is stuck in gear


Hi TIM,I got a 85 nissan 720,and check your clutch fluid in reservoir,may be empty,which means your clutch slave cylinder is bad and not holding pressure,here's a link to it,very easy to replace. here's the part.Your clutch master cylinder uses brake fluid,dot 3.

Apr 14, 2013 | 1995 Nissan Pickup

1 Answer

I need the firing order for 1990 chevy 4 cylinder 2wd pickup


1999 Chevrolet S10/T10 P/U 2WD 2.2 liter L4 VIN "4"

cab1d08.gif


Hope this help (remember comment and rated this).

Apr 30, 2010 | 1990 Chevrolet S 10 4WD

1 Answer

Where is the fuel filter of a 1990 pickup truck located?


If you have the four cylinder, should be on the right side engine block, close to the starter motor. I change mine by going over the right front wheel.

Sep 26, 2009 | 1990 Toyota Pickup

1 Answer

Frequent clutch changes on Hyundai H100 Pickups


I own H100 is at 121000 km now I have never changed clutch.I agree with the dealer when they say the driver sometimes are little bit harsh on vehicles

Mar 23, 2009 | 2008 Hyundai Tucson

2 Answers

1995 nissan truck 2wd, 4 cyl, 5 speed manual: You can move through all the gears when the engine is not running, but when the engine is running you can not get it to go into gear. It seems the clutch is...


The clutch disk has broker, a piece of the friction disk material has boken loose and is wedged between the friction disk and the preasur plate. I had this happen to my '77 280Z. You will need to replace the friction disk.

Dec 02, 2008 | 1994 Nissan Pickup

1 Answer

Too high engine rpm at freeway speeds


that is a normal rpm for the nissan pickup (hardbody)

Nov 27, 2008 | 1997 Nissan Pickup

1 Answer

Clutch pedel will not come back up.must pull it up with your foot.1990 twin turbo 300.


You've lost the integrity of the clutch hydraulic system. Chances are that either there is air in the system, the slave cylinder or the master cylinder has failed.

First step is to bleed the clutch. See if that's a fix.

A slave cylinder is down on the transmission and is relatively easy to change (only two mounting bolts, one hard hydraulic line, and an accordion-boot covered plunger). When it's changed out, the clutch needs to be bled afterward. If it's a clutch master cylinder, that's where the clutch fluid reservoir is underhood (next to the brake fluid reservoir, just to the right as you face the front of the car). Removal requires undoing the lines coming out of the cylinder, removal of the locating/mounting bolts/studs, and disconnection of the plunger rod from the back of the clutch pedal, way up under the dash. Once it's replaced, bleeding the system is required, and you also may have to adjust the pick-up point of the clutch by turning the nuts on the plunger rod - it only takes a slight turn to change the pickup point dramatically, so go slow with that.

I'd do the slave cylinder first - it's more easily accessible, significantly less expensive, and quicker to change. If it's not a fix, don't feel too badly about changing it since it's only about a $25 part and it is prone to failure, so at the very least, you've eliminated a potential problem down the road. If the slave is not a fix, I'd change the master.

Jul 25, 2008 | 1990 Nissan 300ZX

Not finding what you are looking for?
1991 Nissan Pickup Logo

Related Topics:

650 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...