Question about 2004 Mitsubishi Endeavor

Open Question

Change headlight bulb on 2005 mitsubishi endeavor

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

AlmostBob
  • 550 Answers

SOURCE: how do i change the headlight bulb in a 2005 sebring convertable

Lift up the hood, the bulbs are changed from the engine compartment
behind the lamp are connectors, pull it off, and the retainer that holds the bulb in
replace bulb
replace retainer
replace wire
close hood
usually takes longer to type than to do

Posted on Jul 14, 2008

davidsspa572
  • 51 Answers

SOURCE: CHANGE HEAD LIGHT

Hello thank you for using FixYa.com my name is David,Here is the instructions you requested.

There can be slight variations in procedure from one model to another when replacing headlights. For instance, on some models the turn signal light assembly must be removed before the headlight can be replaced. Overall, however, the procedure does not differ much from the following typical instructions.
Make sure the replacement bulb is the same type and part number as the one that is being replaced.
To Replace:

  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).

Posted on Nov 08, 2008

  • 166 Answers

SOURCE: how do I change my headlight bulb

go to your parts suppler and ask for a H4 globe pop your bonnet and remove the plug on the back of your head light then remove the rubber boot paying attention to which way it cam off then you will find a spring clip unclip it but be careful not to damage its anchor point. remove old globe an throw away take new globe out of box DO NOT TOTCH THE GLASS OF THE GLOB AS IT WILL CAUSE THE GLOBE TO BLOW STAAIGHT AWAY AFTER FITTING IT handle the globe by the metle bass and fit it, refit spring clip and rubber boot fit the plugf and check the operation of the light

bingo you are done have a nice day

Posted on Dec 21, 2008

keeperoffire
  • 106 Answers

SOURCE: How to change the headlight bulb on a 2001 mitsubishi galant?

You shouldnt have to pull the whole lens assembly.On the back of the lens assembly(inside engine compartment)you should find what looks like a big round nut where the wires go in.unscrew that nut and your headlight should come out and you can insert the new one.Its a halogen bulb.

Posted on Mar 04, 2009

  • 3 Answers

SOURCE: Cabin Air Filter - 2004 Mitsubishi Endeavor (Where?)

IT IS IN BEHIND THE GLOVE COMPARTMENT YOU HAVE TO TAKE IT OUT BY UNSREWING AND START FROM YOUR RIGHT SIDE

Posted on Jun 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a way to reset keyless entry for 04 endeavor?


Search Results

    2004 Mitsubishi Endeavor Key Fob Remote Programming ...

    blog.keylessentryremotefob.com/.../04/2004-mitsubishi-endeavor-key-fo...
    Apr 25, 2013 - 2004 Mitsubishi Endeavor Key Fob Remote Programming Instructions ... you might have visit us at Keylessentryremotefob.com You can also ...

    Mitsubishi - Free Keyless Remote Fob Entry programming .

    How To Replace Mitsubishi Endeavor Key Fob Battery 2004 ...

    ? 2:04
    www.youtube.com/watch?v=yeQRdre7O0Q
    Oct 31, 2014 - Uploaded by Keyless Entry Remote Inc
    ... will show you How To Replace Mitsubishi Endeavor Key Fob Battery 2004 2005 To Order This Remote ...

Nov 01, 2015 | Cars & Trucks

1 Answer

Change license plate lamp bulb 2004 Mitsubishi endeavor


there SHOULD BE AT LEAST TWO SCREWS HOLDING THE LICENCE PLATE LENS IN PLACE .REMOVE THE SCREWS AND PULLTHE BULBS OUT,THEN PUT (NEW BULBS)IN PUT IT BACK TOGETHER,MAKE SURE THE NEW BULBS WORK BEFORE PUTTING IT BACK TOGETHER

Feb 26, 2014 | 2004 Mitsubishi Endeavor

1 Answer

My 2005 mitsubishi endeavor has a wrench light on the display


I have an '06 endeavor and the wrench indicates it's time for an oil change.The computerized service log(for lack of a better phrase)is set for 3000 miles after each oil change which activates the wrench light.It is reset by myself or the mechanic after each service. I HOPE THAT HELPS!

Aug 30, 2011 | 2006 Mitsubishi Endeavor

1 Answer

I have a 2005 Mitsubishi Galant and am trying to change the headlight bulb. How do you remove the "dead" one ?


There is a plastic ring that holds the bulb in place . You need to spin the ring counter clockwise to unhook the ring from the reflector. If the battery is in the way you may have to remove it before taking out the headlight. The wire harness unplugs from the back of the bulb but may be stuck. If you try to unplug the harness before removing the bulb you might brake the retaining ring. Therefore, turn the ring, wiggle the bulb free of the reflector, then get a grip on the bulb and work the harness plug off the bulb. Now place new bulb in the reflector, put on the retaining ring and turn clockwise till it stops, plug in the bulb harness, and test the bulb by turning on high and low beam.

Dec 17, 2010 | 2005 Mitsubishi Galant

1 Answer

How do i change the wire harness for the headlight


Welcome to FixYa.com

Buy the repair kit for the head light at the dealer and cut one wire at a time and splice one at a time to not crimp the wrong wire. Yes you will need a wire crimper.

Thank you for using FixYa.com, Regards, Lee Davidian


A 4^^^^ THUMBS- UP rating is appreciated for answering your FREE question!!!!!

Sep 30, 2010 | 2005 Mitsubishi Endeavor

1 Answer

How do you adjust the headlights on a 2004 endeavor


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 12, 2009 | 2004 Mitsubishi Endeavor

1 Answer

How do I replace the headlight in my 2005 mitsubishi lancer


Hi. While looking into your question I came across another posting of the same question for a 2004 Mitsubishi Endeavor and I believe it could help you. I put it in a link below. The instruction are basically the same. I hope this helps. Let me know if I can be of anymore assistance.

2004 Mitsubishi Endeavor Headlight Replacement

Nov 28, 2008 | 2004 Mitsubishi Endeavor

3 Answers

CHANGE HEAD LIGHT


you change the bulb from inside the engine compartment . raise the hood and feel for a plastic retaining ring in the back of the headlite. Loosen 1/4 turn and bulb socket and old bulb will pull out from the headlite assembly Unplug the old bulb and replace with new one . assemble in reverse order.

Nov 02, 2008 | 2004 Mitsubishi Endeavor

Not finding what you are looking for?
2004 Mitsubishi Endeavor Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...