Question about 1994 Ford Econoline

2 Answers

When I pulled the engine in my 1994 Ford Van 4.9 Straight 6 the torque converter came out too. How do I get it off the engine?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 117 Answers

It's bolted to the fly wheel. You will have to remove the the fly wheel cover and probably the starter. When one bolt is removed, turn the engine until you see another bolt, there are 3 or 4 bolts.

Posted on May 12, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,826 Answers

There are bolts in between the flywheel and the engine.There should be four,you will have to turn the flywheel to get to the bolts,the converter should have been un bolted before removing the engine

Posted on May 12, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine stalling after warmup when stopping but not in low1


You may want to have the TCC (TORQUE CONVERTER CLUTCH INVESTIGATED). THIS IS ALSO KNOWN AS A LOCK-UP TORQUE CONVERTER. Controlled by the computer. Hope This Helps.

Nov 12, 2013 | 1994 Ford Econoline

1 Answer

94 Dodge Ram 3500 Van runs fine, but will not move much. Previously would start in Park, now will only start in Neutral. After sitting for a few hours or a day it will run a few hundred yards but then...


Dumb question but, did you check the trans fluid? A torque converter can hold 6 quarts of fluid or more and if the van has sat for an extended period of time the fluid drains from the converter and will come out of the vent tube causing a no movement issue

Oct 21, 2013 | 1994 Dodge Ram 3500

1 Answer

1994 ford tempo 4 cyl need to know tourqe and order of head bolts 10 total ,thanks


Torque sequence ------------ front ' 10 6 2 3 7 ' of ' ' engine ' 9 5 1 4 8 ' ------------ Step 1: torque in sequence to 52-59 Ft/Lbs Step 2: torque in sequence to 70-76 Ft/Lbs Recheck final torque in sequence
Hope it helps you.

Jul 30, 2011 | 1993 Ford Tempo

1 Answer

How much trasmission fluid to you need to do a flush on a 1995 Jeep Grand Cherokee straight 6?


The torque converter holds about 4 -6 qt's itself.Not positive on your model would star with 4 then check.This is if you did not remove the torque converter, good luck to you.

Mar 27, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

I took my 1995 Ford Aerostar to have the flexpipe, muffler, and tailpipe replaced. I shopped around, and Budget Muffler in Kent Ohio stated that they would repair the care for $160+tax. When I picked...


You are right. The engine flexes differently, but not less. The designers that put the engine sideways also put the flex pipe in the design, and the shop is just saving money. I'm a mechanical engineer, and I can tell you the stresses on the joints will be higher without the flex pipe. I can't say for sure something will crack, but it is certainly more likely.

Feb 11, 2011 | 1995 Ford Aerostar

3 Answers

How much oil in my van


5-6 quarts if empty.

May 31, 2009 | 1994 Ford Econoline

1 Answer

I have a knocking sound from either lower end of engine or torque converter. The van has 126,000 miles and is a Ford 2005 E250.


sounds like rod bearings or a loose torque converter, check the bolts to the converter and also check the flex plate for cracks, that can cause a knock as well.

Mar 29, 2009 | 2004 Ford E250

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Head torque settings


Hey graham, there are 4 engine possibilities in the 94 E350, I'm going to guess it's the 5.8, as that is the most common option, if it's the 7.5 gas, or 4.9, let me know, as torque is different.
105 - 112 ft lbs. tightening sequence as follows"

front of vehicle 9 5 1 3 7
10 6 2 4 8

Jan 02, 2009 | 2002 Ford E350

Not finding what you are looking for?
1994 Ford Econoline Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...