Question about 1987 Ford Tempo

1 Answer

Where is the ful pressure relay switch - 1987 Ford Tempo

Posted by on

  • yadayada
    yadayada May 11, 2010

    under the hood.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

There is no fuel pressure relay, there is a fuel pressure regulator sit on the your throttle body if it's fuel injection, that year came with carb. or injector's.

Posted on May 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I havw a 1997 dodge 3500 v10 turned it off now it won't start put a new ful pump but still wont start


Before you replaced the fuel pump did you test battery power an ground at the fuel pump ,did you hook up a fuel pressure gauge ! Does the vehicle have spark ? Check the ASD relay , this powers the fuel injectors an the coils ! No Start Diagnostic Basics EricTheCarGuy

Sep 30, 2015 | Dodge Cars & Trucks

1 Answer

02 3.3 xterra ac clutch relay no signal to relay


Voltage to the clutch relay is sourced from the PRESSURE SWITCH (SENSOR) at the receiver/dryer. If there is insufficient refrigerant pressure, or if the pressure switch is bad, the clutch relay will not get control voltage from it. Check your refrigerant pressure, and check to see if there is voltage on both sides of the switch when the a/c is turned on (engine running). If your low-side refrigerant pressure is greater than the preset minimum (usually about 20-30 p.s.i.), and you have voltage at one side of the pressure switch but not the other, replace the pressure switch. If you do not have voltage at either side of the pressure switch, the problem will be between that connector and the fuse panel (including the electronic controls in the dashboard).

May 15, 2014 | Cars & Trucks

1 Answer

Mr2 fuel pump relay location


looking into engine bay there are a group of relays etc just to the right of distrbuter the ful pump relay ,if a toyota make will have it written on it ,if not its between the fuse box and what look like heat sink plates bolted to side panel

Mar 30, 2014 | Cars & Trucks

1 Answer

97 chevy suburban AC clutch won't engage pressures


Looks like the low pressure switch gets power from a 10amp ac fuse. Power then goes to the ac relay which is powered on by the ac heat controller on the dash. Power then goes thru the high pressure switch to the compressor. The ac relay is grounded to the body. Do you have power on the lite and dark green wires going into the relay and is it grounded ?

Jul 26, 2013 | Cars & Trucks

1 Answer

I have a 84 caddy deville,why is the ful pump fuse keeps blowing


either the fuel pump is shorted, the wiring going to the fuel pump is shorted to groung, or 1 other option, the oil pressure switch is shorted. gm back then ran the fuel pump wiring to the oil pressure swtch as a back up system for the fuel pump. one of these is your problem

Mar 06, 2011 | 1984 Cadillac DeVille

1 Answer

1997 Linclon car No power to A/C clutch.


take the pressure switch connector off and jump connector- if clutch engauges you either have bad low pressure switch or are low on freon.

Aug 25, 2009 | 1997 Lincoln Town Car

1 Answer

Ful pump installed and truck will not start


what probably happened is maybe your fuel cut off switch engaged and cut off your fuel going to the motor as a built in safety feature. check that. also check your fuel pressure in the motor and see if enough pounds of fuel pressure is squirting through to the fuel rail and if not check your filters which may be clogged and not be allowing fuel to pass thru the line to the motor. last but not least check the ecm Brain computer. maybe it is sending the wrong commands to fuel pump and maybe memory has been lost in ecm.

Jul 26, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

Rover 200 overheating


Check the usual things: like a stuck thermostat, a slipping water pump belt and a clogged radiator.  Then check that the cooling fans are turning on...they consist of a temp sensor, a relay and the fan motors.  If all these are correct brace yourself for a blown head gasket.  This is indicated by exhaust smell in the coolant and a lot of pressure in the cooling system.

Mar 22, 2009 | Honda S2000 Cars & Trucks

1 Answer

Problem with Chevrolet 4.3 Vortec fuel pressure / oil pressure relay


a bad fuel pump relay will not cause vehicle to only run under 50. the oil pressure switch does bypass relay when pressure builds up. if you are having problems with running need to check fuel pressure. possibly caused by clogged fuel filter

Feb 14, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...