Question about 2000 Toyota Sienna

1 Answer

Ignition key wont turn in 2000 toyota sienna. how do i change it.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Installed new switch wont start

Posted on Aug 24, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
countrysi248
  • 443 Answers

SOURCE: 2000 Toyota Sienna Minivan car alarm goes off.

1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Posted on Apr 25, 2009

oldfishead
  • 155 Answers

SOURCE: '00 Toyota Sienna-stuck door

the lock actuator is binding/hanging up, replace it and lube the linkages this should cure that problem....hope this helps...let me know...GL

Posted on Jul 06, 2009

catbob007
  • 70 Answers

SOURCE: Changed battery on 2005 Toyota Sienna, dvd player doesn't work

call dealor

Posted on Jul 27, 2009

  • 2 Answers

SOURCE: integration relay p/n 82641-08020 for my 2000 Toyota Sienna van

Dealer Item ` $200
Junk Yard ~ $100
https://toyotapartscenter.net/toyotasiennaparts.html?gclid=CPX5u8HUlZ4CFSn6agod6Ae1oQ sells them for $167.17 + shipping and tax
PH; 800-516-1455
I recommend a pull, light tap and reconnect, recheck B4 buying. Also, shop manual has proper test procedure, Pages BE16-17

Posted on Nov 18, 2009

  • 1 Answer

SOURCE: toyota sienna interior lights not working

The problem is in the sunvisor light. You will have to take the light assembly off and you will find wires have become disconnected.

Daviscacare.com
757-689-4701

Posted on Jan 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I changed the battery in my 2001 Toyota Sienna and now my radio won't work.


Press station 1 and 6 and turn the ignition key to on position but donot start the vehicle, you will see the unlock code flashing, note the number that is your radio code, read your vehicle manual and insert code to unlock.

Aug 11, 2011 | 2006 Toyota Sienna

4 Answers

I have a 2000 toyota corolla and the key will only turn to acc. We have tried the other key. The stering wheel is unlocked. We have jiggled the shifter to make sure it is in park.


See if you turn the wheel and try to turn the key at the same time if it releases. We might get a free spot where the key should turn. The lock may be in a bind and pressure on it may release it.
Clean and lubricate the lock cylinder. Electric cleaner to flush the dirt and liquid graphite to lubricate. A substitute for the electric cleaner is a spray of isoprophyl alcohol.
You may also need to tap the assembly for the ignition switch to release the mechanical parts. See if you can get the cover of the steering column off to gain access to the ignition switch assembly.
Check also if the spare does the same, other wise the key may have deformed.

May 02, 2011 | Toyota Corolla Cars & Trucks

1 Answer

I just replace the battery in my van, and sometimes it will start and sometimes it wont, if I turn the key on and off a few times, then it will start. any ideas????


Hello,
It sounds like you may have a bad ignition switch. That may be the first thing that I would have checked.

Good luck!

Feb 03, 2011 | 2000 Toyota Sienna

1 Answer

A red flashing car shape light flashing on my 06 toyota sienna van?


Is the immobilizer, if there is no key in the ignition is ok if flashes, if it flashes when the key is in the ignition the key is bad car wont start.

Dec 31, 2010 | 2006 Toyota Sienna

1 Answer

Ignition key goes to acc position only on my 98


probably bad key switch make sure not wrong key

Mar 14, 2010 | 1998 Toyota Sienna

1 Answer

TOYOTA SIENNA MAINT REQD LITE CAME ON AFTER SCHEDULE MAINTANANCE


If the dealer/mechanic did the service early the light will come on when service is DUE. Go back to him and have it turned off. Search the web someone may have the procedure posted. Usually simple. Google "Toyota service light reset" or "Toyota Maintence light reset" Try this one
  1. With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B).
  2. Turn the car off (ignition key to the OFF position).
  3. Push in AND HOLD the button/knob that switches the odometer
  4. Turn key to ON position without starting the car. You will notice the maintenance light blink and go out.
  5. Release the odometer button/knob.
  6. Turn key to OFF position.
  7. That's it! The "MAINT REQD" light has been reset to warn you to change your oil in another 5,000 or 7,500 miles or so.

Feb 05, 2010 | 2004 Toyota Sienna

1 Answer

How to reset maint req lite on a 2005 sienna


Reset the "MAINT REQD" Light on Toyota Sienna:
  1. With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B).
  2. Turn the car off (ignition key to the OFF position).
  3. Push in AND HOLD the button/knob that switches the odometer
  4. Turn key to ON position without starting the car. You will notice the maintenance light blink and go out.
  5. Release the odometer button/knob.
  6. Turn key to OFF position.
  7. That's it! The "MAINT REQD" light has been reset to warn you to change your oil in another 5,000 or 7,500 miles or so.

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 2006 Toyota Sienna

1 Answer

Integration relay p/n 82641-08020 for my 2000 Toyota Sienna van


Dealer Item ` $200
Junk Yard ~ $100
https://toyotapartscenter.net/toyotasiennaparts.html?gclid=CPX5u8HUlZ4CFSn6agod6Ae1oQ sells them for $167.17 + shipping and tax
PH; 800-516-1455
I recommend a pull, light tap and reconnect, recheck B4 buying. Also, shop manual has proper test procedure, Pages BE16-17

Sep 24, 2009 | 2000 Toyota Sienna

1 Answer

How to replace ignition switch on a 2000 Toyota Sienna?


turn the key to acc and remuve push the button button

May 04, 2009 | 2000 Toyota Sienna

2 Answers

2000 Toyota Sienna Minivan car alarm goes off.


1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Apr 25, 2009 | Chevrolet Malibu Cars & Trucks

Not finding what you are looking for?
2000 Toyota Sienna Logo

Related Topics:

296 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...