Question about 2006 Ford Focus

1 Answer

Dtc p0087 what is this my car is ford focus 3600 km

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

If you are seeing a check engine light of any type with so little mileage I would have it checked at the dealer however being a 3006 this most likely points to the O2 Sensor.

Posted on May 11, 2010

Testimonial: "thank you my frend."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Chevy Kodiak c4500 duramax desiel i replaced the MAF sensor because the code reader said P0102 now it says P0087 that is the problem but everytime I'm hauling something the engine always decreases its...


DTC P0087: Fuel Rail Pressure (FRP) Too Low

Circuit/System Description
The fuel injection pump supplies high pressure fuel to the fuel injection rails, and then to the fuel injectors through high pressure pipes. The fuel rail pressure (FRP) sensor is a three wire sensor mounted in the right fuel injection rail. The FRP sensor uses a 5-volt reference circuit , a signal circuit, and a low reference circuit to monitor fuel rail pressure. This information is sent to the engine control module (ECM) to assist in the fueling of the engine.

Fuel Pressure Regulator Solenoid Supply Voltage
P0088, P0090
P0088
P0090
P0087, P0191, P2510
Conditions for Setting the DTC
P0087
• The actual FRP is more than 15 MPa (2,176 psi) below the desired FRP.
OR
• The actual FRP is less than 22.5 MPa (3,263 psi).

Action Taken When the DTC Sets
• DTCs P0087 and P0088 are Type A DTCs.
• The ECM commands the engine to operate in the Reduced Engine Power mode.
• The message center displays Reduced Engine Power.

Important: Because of the cleansing properties of the biodiesel, switching from the straight diesel to a biodiesel blend can prematurely restrict the fuel filter with normal deposits in the fuel system. A fuel filter replacement might be required sooner than the recommended interval.
P0087
If DTC P0090, P0168 or P0191 is also set, refer to Diagnostic Trouble Code (DTC) List - Vehicle.
Ignition ON for 90 seconds, verify the scan tool FRP Regulator Command parameter is less than 20 percent.
? If greater than the specified range, replace the ECM.
Attempt to start the engine.
? If the engine does not start, refer to Engine Cranks But Does Not Run.
Install the CH-48027 to the fuel rail service port and slowly increase the engine speed until reaching wide open throttle (WOT). The value should be between 1-4 inches Hg vacuum.
? If more than the specified value, inspect for restricted fuel filter or damaged supply lines.
? If no restriction was found, test for high fuel return flow. Refer to Fuel System Diagnosis - High Pressure Side.
With the engine idling or at an idle, command the fuel pressure control to 180 MPa (26,106 psi) with a scan tool. Observe the Actual Fuel Rail Pressure parameter. The actual fuel pressure should be the same as the commanded pressure.
? If the Actual Fuel Rail Pressure is less than 165 MPa (23,931 psi), refer to Fuel System Diagnosis - High Pressure Side.
Important: If the fuel temperature is near 121°C (250°F) during the duplication of the complaint, or in the Failure Records for this DTC, inspect for a restriction in the fuel cooler air flow or the fuel heater always ON. Refer to Fuel Heater Always On.
Operate the vehicle within the conditions for which the customer complaint occurs while observing the CH-48027 . You may also operate the vehicle within the conditions that you observed in the Freeze Frame/Failure Records.
? If the vacuum was more than 12 inches Hg of vacuum at any time in the operating range, inspect for kinked or restricted fuel supply lines.
Operate the vehicle within the conditions for which the customer complaint occurred. Observe the Actual fuel Rail Pressure and Desired Fuel rail Pressure parameters with a scan tool. Fuel pressures should be the same for both parameters.
? If the Actual Fuel Rail Pressure is less than the Desired Fuel Rail Pressure, refer to Fuel System Diagnosis - High Pressure Side.
? If fuel system tests normal, refer to Diagnostic Aids.

Aug 20, 2017 | Cars & Trucks

1 Answer

Dtc p0087 pressure fuel


Low fuel pressure at rail. Fuel filter been checked?

Mar 05, 2014 | 2008 Dodge Sprinter

1 Answer

Ford focus car showing dtc code E200,E510,E197, D900


The following link will provide you with all OBD-II codes for your Focus. CLICK HERE

Jun 22, 2012 | 2006 Ford Focus

1 Answer

2003 Focus stutters accelerating between 60-80 km


Had similar problem on '04 Zetec. Turned out to be coil pak.

May 15, 2012 | 2003 Ford Focus

1 Answer

I cleared the three DTC codes previous asked, which were P0088, P0087,nad P2291, re-started the engine and getting a DTC Code P1000 can you tell me what this code is. The three previous codes started when...


P1000- on-board dianostic systems readiness test not complete, 1. obd monitors and drive cycle incomplete 2.keep alive memory(KAM) cleared, wat to do and try. remove power take off fuse(PTO) then cleared the code,disconnect pcm connector and visually check for corrosion

Jun 21, 2010 | 2008 Ford F 250 Super Duty 4WD

4 Answers

2008 Ford F250 6.4 turbo diesel, have 3 DTC codes


P0087- low pressure fuel system. Fuel pressur valve stock open, Fuel volume control valve stuck close, Leaking fuel injector,P0088- fuel pressure contorl valve stuck close, Fuel rail pressure sensor P2291-all @ at the above, means to say poor fuel quality

Jun 21, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

Ford focus tdci 1,6 year 2006 ,please help me dtc


code 21 is camshaft position timing. Timing improperly set or solenoid stuck open.

May 09, 2010 | 2006 Ford Focus

1 Answer

2004 Ford Focus ZTS with DTC P2004.


my 04 zts was throwing the same code. I got under the car and found a vacume hose that was off of an actuator thing ,put it back on and hasn't thrown code since

Mar 08, 2010 | 2003 Ford Focus

1 Answer

Timing belt 2003 ford focus


Check with the dealer to get belt change interval. 100,000 to 160,000 km is the most recommended.

Jul 22, 2009 | 2003 Ford Focus

Not finding what you are looking for?
2006 Ford Focus Logo

Related Topics:

816 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...