Question about 2001 Dodge Neon

1 Answer

How do I replace the reverse light? I can't figure out how to get to it.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

Ok when you have your trunk open along where the lights are you should see some plastic nuts. there is about 8 to 12 of them diff. cars take more and some take less. but when you take those off the back cover you will be able to lightly pull the carpet away from the back wall. that is where you will see the light sockets and take the bulbs out

Posted on May 11, 2010

Testimonial: "Thank you. I wasn't sure if I was supposed to remove all of those nuts or approach it from the outside of the car. You were a great help. Thank you. "

  • loke_1367 Jan 28, 2011

    Do you where the fuse is located for the reverse lights? changed the bulbs and it still doesn't work!!!



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Break lights and tail lights will not come on. Both sides. I replaced the bulb.

Brake light fuses should be in the "fuse box" under the hood.

Aug 28, 2015 | 2002 Jaguar X-Type

1 Answer

How do I replace a brake light switch on my 2007 kia rondo?

It's located on the brake pedal. you'll need a 14mm wrench. There are 2 14mm nuts that sandwich the switch to the bracket. take the bottom nut off and the switch will come off. Install reverse of removal but you need to adjust the switch depth once its on the bracket. then snug the bottom nut and plug in the switch.

Aug 06, 2012 | 2007 Kia Rondo LX V6

1 Answer

My reverse lights are out on my nissan sentra gxe 99 cannot figure how to get to or replace bulbs

Just open the trunk lid and snap the plastic cover at the back of your tail light assembly and the bulb socket assembly will come off. Push and twist the bulb to be replace. Same reverse way when putting it back.
Hope that helps you out.

Jul 30, 2011 | 1988 Nissan Sentra 2 Door

2 Answers

All fuses are good - brake lights, rear running lights work fine. but the reverse lights won't come on when put into reverse. Any idea what might be going on? As far as I know the bulbs are still good...

You will need to either replace or adjust your backup switch, it is located on the transmission next to the shifter. Hope this helps, thank you for using FixYa!

Jul 06, 2011 | 2000 Pontiac Sunfire

1 Answer

I have an 07 f550 long wb and im trying to figure out what color wire is the hot wire for the reverse lights,this is on a flatbed rollback truck,i need to splice in somewhere in the cab if possible

being a roll off the wiring can be different depending on what shop installed the bed,some shops replaced the reverse and tail lights from factory for clearance issues. others just removed them and used the lights on the headache rack. the stock ones are either pink or green on most models

Mar 15, 2010 | 1999 Ford Super Duty F 550

1 Answer

Left rear turn signal, brake light and reverse not working

Did you ever figure this out? I've got the same exact problem with my tahoe.

Apr 11, 2009 | 1999 Chevrolet Tahoe

1 Answer

The reverse lights and heater stay on after the car is off.

It isn't a fuse. A fuse will break the circuit if it is drawing too much power. What you have is circuits that are connected by the ignition switch, that should be disconnected when the key is off. This means that the ignition switch is not operating correctly, and either needs adjustment or replacement.

Mar 14, 2009 | 1999 Ford Expedition

1 Answer

How to access front turn signal for replacement

Here you go, removal & installation of:

Front Parking/Turn Signal Lights:
  • Remove the screws from the the lens and separate the lens from the bezel
  • Remove the screws from the turn signal housing and pull it out
  • Turn the bulb socket CCW 1/3 turn and remove it
  • Installation is the reverse of this procedure
Side (Front) Marker Lights:
  • Remove the screws from the marker lens
  • Separate the lens from the headlight
  • Pull the bulb from the back of the lens
  • Installation is the reverse of this procedure
Hope this helps


Jul 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2001 Dodge Neon Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides