Question about 1998 Chrysler Town & Country

1 Answer

ReplaceTentor pully on 1998 Town and Country

Replace Tentor pully on 1998 Town and Country. Belt continue to come off. Have replaced all pullies. Has eaten three belts. The lining up of belt is off at the tentor pully

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 834 Answers

It very well could be the tensioner if it does not sit straight, or the idler pulley if the bearings have gone out, but usually 99% of the time it is the power steering pulley that is pulling out from the power steering pump, and that is usually what is causing the belt to mis-align especially at the waterpump pulley, check the alignment of that pulley very well.

Posted on May 11, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The blet to the engine keep coming off i have had the pullie replaced but the belt keep coming off at least once or twice a month.

not sure what pulley you are talking about but the automatic belt tensioner may be the problem if its not keeping enough tension on the belt through out the accelerating and decelerating of the motor.this is usually the problem.

May 05, 2011 | 1998 Chrysler Town & Country

1 Answer

Belt keeps slipping off my 2000 chry town and country

Most commonly the pully is worped, If you have 'nt replaced the bely it could be ***** out.These are what usually make this happen, Good luck to you.

Apr 12, 2011 | 2000 Chrysler Town & Country

2 Answers

How to replace back belt for ford aerostar '96

take a ratchet and loosen the tension pully( ideler) and remove the belt pay attention how it is routed around the other pullys and replace it with a new belt and then tighten it back on....

Jul 09, 2010 | 1998 Ford Windstar

2 Answers

Is there an adjustment on the tensioner pully?

the serpentine belt tensioner is spring loaded and has no adjustment. it must be replaced

May 25, 2010 | 1998 Chrysler Town & Country

1 Answer

Need to loosen the drivebelt to remove the alternator

Follow the belt around the pully's and look for a pully that is attached to an arm. this is a spring loaded tensioner pully. on this tensioner, you can often fit a 3/8 drive ratchet directly in the back. if so that how you'll be able to release the tension on the belt. otherwise use a socet (if there's enough room) or wrench on the nut in front as if tightening. this will release the tension on the belt.

Hope this helps!

Mar 27, 2010 | 2003 Chrysler Town & Country

1 Answer

2000 town & country van. serpintine belt slips off. turn corners in slush and away it goes.

Sounds like the belt is worn out or the tenchiner pully is worn out so replace the belt and if it still does it then you will have to change the pully, but most of the time when this happens it is the belt so replace the belt and you should be good to go.

Mar 03, 2010 | 2000 Chrysler Town & Country

1 Answer


good day. well maybe it will cost you not more than a hundred dollar.

Feb 04, 2010 | 1998 Lincoln Town Car

1 Answer

How do you change a tension system on a 1999 chrysler town and country the engine is a 3.8

if your set to do it. First you have to dismantle the front of the motor. then unload the tension pully. unbolt the water pully the steering pump. then the tensioner. replace here's where it get hard in the small space you'll have to put tension on the ten to put belt back on. broke hand here.

Dec 06, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

Broken pully on the power steering pump of a 1998 Chrsler Town an

just replace the pulley it is cheaper take to autostore that has a press and they can press the new one on (try to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you)

Mar 21, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1998 Chrysler Town & Country Logo

305 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides