Question about Cars & Trucks

1 Answer

Engnie removable how much trouble will I have taking it from the tranmisson in the car and out the top

Posted by Anonymous on

1 Answer

If your doing the engine,drop the cradle with trans and engine.

Posted on May 12, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2002 yokon xl with a 5.3l engnie have coolant comeing from the drive side at the back of the power streeing pumup


Sounds like your heater core might have ruptured. Will need to remove complete dash board to replace this component.

Nov 12, 2016 | 2002 GMC Yukon XL

1 Answer

Ss commdore mamaul 1994


Check to see if the kickdown cable from the throttle linkage to trans is working.
Next step is to get someone with auto experience to drive it and give a more accurate diagnosis.

Jul 01, 2014 | Holden Commodore Cars & Trucks

1 Answer

Trouble shooting code p0734


code p0734 refers to gear 4 --incorrect ratio===causes--wiring---TR sensor/ switch--shift solenoids---transmission mechanical faulty

Jan 13, 2014 | 2000 Mazda Millenia

1 Answer

How to install engnie freeze plug 90 toyota celica st


Hi, are you talking about anti freeze, if so it goes in the engine coolant in the radiator, check the manufacturers specifications for the correct ratio of anti freeze to water for your climate, which I assume changes from season to season. In winter you may have to use 100% anti freeze for the coldest times of the year.

Dec 20, 2012 | Cars & Trucks

1 Answer

How to remove a tranmisson on a 2001 dodge carvan ?


if you don't know what your doing it will take you and a couple of your buddies to get it done you will need jacks and jack stands remove both wheels remove both tie rod ends remove the bolts fro the bottom of the struts remove if you have a trans oil pan plug to remove trans fluid remove all electrical and trans cable go under car near trans and engine look up remove the access panel to access the flywheel and torque convertor take the bolts off separating the torque from the flywheel remove the trans bolts separating the trans from engine when installing make sure the torque is seated in the trans really good spin the torque a couple of times until you hear a it fall into place begin reinsatalling in reverse order until the last screw is in place

Sep 25, 2012 | 2001 Dodge Caravan

1 Answer

Car runs and shifts but does not move could this be a sensor?


i had a car that done this it sat for 3 months until i found out that they are 2 different kinds of speedomoter cables one diganel the other a standard speedometer cable mine took the digental if you get under your car an look where the tranmisson is youll see a cable going into the tranmisson if you do its a digintal one an mine was broke at the little bulb that went into the tranmisson an your car will start an shiff gears but it will not move at all replace this an then it will drive a machanic told me i needed a new tranmisson but i didnt so they are 2 kinds of speedomoter cables this was my cars problem

Jun 07, 2012 | 2003 Chrysler PT Cruiser

1 Answer

Ok i have a 2003 ford f-150 pickup it idles up and down, and hesitates on take off but after that its fine i checked the fuel pressure replaced the intake gaskets and put a maf sensor on it does...


possible sticking idle air control valve (iac) held on by 2 bolts on top of enigne, ahs wire connector going to it and is held on by 2 bolts, on your engine i believe it is on the driver side of engnie located under plastic cover for your throttle body...try washing it out with carb cleaner after it is removed, if that helps it, relpace valve with factory componetn


hope this helps

Mar 23, 2011 | Ford F-150 Cars & Trucks

1 Answer

Engnie removable how much trouble will I have taking it from the tranmisson in the car and out the top


its not hard to remove engine from the top. take off any pulleys or tensioners that may be in your way. its really quite simple. remove starter,exhaust,motor mount bolts, torque converter bolts,trans bell housing bolts. remember you have six bellhousing bolts, one on the inside above the trans. also there is a bracket bolted to the trans from the engine just above the cv joint on passenger side. remove rad fans,,alt, compressor,rad hoses, heater hoses,. Please leave comment how it goes.

Mar 17, 2010 | Pontiac Grand Prix Cars & Trucks

1 Answer

WITH THE OVERDRIVE IN MY 92 LINCOLN TOWNCAR TRANMISSON GONE WILL IT EFFECT MY DAILY DRIVING AND WHAT WOULD BE THE TOP SPEED I CAN GO IN THE CAR?


intomthe city you will no note any change. do not exceed 120kmh due it make motor work ay extra rpm and make short its uselife

Oct 07, 2009 | 1992 Lincoln Town Car

1 Answer

Tranmisson dran plug wranch size


The Toyota guide says that a 14mm hex head wrench fits "most" Toyotas from 1986 to current.

May 09, 2009 | 1994 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...