Question about Cars & Trucks

1 Answer

My 01 chevy venture blend door acuator is not working. Is there a way to manually change it when the summer gets here? The ac worked just fine this last summer but I had no heat. The shop manually changed it to the warm setting but now I can't get my ac to cool. I had the shop do this for both the ac and the heat just wondering if I can change this myself?

Posted by Anonymous on

Ad

1 Answer

Why not just make the correct repair to the door or actuator motor and move on.

Posted on May 12, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: My 01 chevy venture blend door acuator is not working.

Your blend door in the Venture is on the driver side of the van, under the dash just above your right knee at the side of your plenum. You will see a white arm that will move to adjust the blend door. The blend door actuator sits on top of the plenum held down with 3 screws. If you did not want to diagnose the problem you could just wire it in place for summer or winter. Personally I would try and diagnose the problem. Hope this helps.

Posted on Nov 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 F150 Lariat. Dual climate control works only on passenger side. Rear temperature controls work fine. Driver side or left vents only blow hot air. Regardless if AC is turned on or temperature...


If the driver's blend door actuator has failed completely, or the wiring to it is damaged, you will not hear any clicking. Check for appropriate voltage at the blend door actuator, and determine from there if it's the actuator or the control unit.

Dec 20, 2016 | 2010 Ford F-150

2 Answers

How do I find the ac heat acuator on a 2001 Pontiac Bonneville sle.


How To Install Replace AC Heater Temperature Actuator ...

? 4:40
https://www.youtube.com/watch?v=mVP09M7hLB4
Jul 21, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/temperature-blend-door-actuator/i/1ahcx00293 ... How To Remove Install Door Chevy Monte Carlo Pontiac Grand Prix ...

GM Blend Door Actuator Repair (Saturn, Chevy, GMC, Buick ...

? 4:28
https://www.youtube.com/watch?v=fER3ZqnYLZg
Jul 11, 2014 - Uploaded by willmacneill
The procedure is the same for most GM blend door actuatorsfrom 1990-2013 (found in many vehicles made by Chevy, GMC, Buick, Pontiac, ...

Mode/Temperature Door Actuators May Fail : Pontiac ...




Jan 16, 2016 | Pontiac Cars & Trucks

1 Answer

2003 Ford Windstar heater acuator located?


Is the heater not working in the front of the van, but is working in the back? You might mean the 'blend door actuator'. It's not easy to get to. The correct way is to remove the dashboard. Search YouTube for 'Windstar blend door actuator' to get some ideas.

Jan 27, 2014 | 2003 Ford Windstar

1 Answer

Cant find the door acuator switch on 2001 monte


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 07, 2012 | Cars & Trucks

1 Answer

Where is the blend door actuator located on 2006 Chevy Silverado?


My ac works, but my heater blows cold air. Is there any way I can replace actuator by going thru the glove compartment?

Nov 04, 2012 | 2001 Chevrolet Silverado

1 Answer

Chevy venture van passenger side AC blows cold, driver's side blows warm to hot


Usually a blend door problem, either the control or the blend door itself.

Jul 03, 2012 | 2000 Chevrolet Venture

1 Answer

I have A 2001 CHEVY TAHOE 5.3L my ac blows nice and cold on the rear but up front in the dash area its hot air coming out. could it be my blendoor acuator or my knobs ? or what could it be


THEY HAVE ISSUES WITH THE BLEND DOOR ACUATORS ..YOU CAN TRY TO RESET THE BATTERY FOR 5MINS DISCONECTED.IF NOT ITS BEHIND THE DASH.80 TO 100 BUCKS FOR PART.ALOT OF LABOR TO FIX

Aug 05, 2011 | 2001 Chevrolet Tahoe

1 Answer

The fan works, air conditioning works, but the air wont heat up(knob turns to hot on thermostat). is it a vacuum hose problem, and how do we get to it?


The most common cause of this in the Ranger and the Explorer is that a part called the air temeperature control blend door acuator or the blend door shaft that the electric actuator moves has broken, this door is what shuttles between the heater core and the AC core and provides either heated or cooled air, or a blend of the two hot and cold air streams.

Dec 26, 2010 | 2008 Ford Ranger 2WD

1 Answer

My 01 chevy venture blend door acuator is not working. Is there a way to manually change it when the summer gets here? The ac worked just fine this last summer but I had no heat. The shop manually changed...


Your blend door in the Venture is on the driver side of the van, under the dash just above your right knee at the side of your plenum. You will see a white arm that will move to adjust the blend door. The blend door actuator sits on top of the plenum held down with 3 screws. If you did not want to diagnose the problem you could just wire it in place for summer or winter. Personally I would try and diagnose the problem. Hope this helps.

Mar 16, 2010 | 2001 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

390 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...