Question about Kia Borrego

1 Answer

HI I REQUIRE THE TIMING SET UP FOR A 2004 2.5 MECHANICALLY DRIVEN (NOT COMMON RAIL) KIA PREGIO MINIBUS

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi! This can help for additional info on timing the engine. Valve clearance intake should be 10 to 12 thousand and 14 thousand for the exhaust. Hope this helps and have a good one!

Posted on May 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset injector pump timing for a Nissan Navara QD 3.2


if it is a common rail diesel, the timing is set by the ECMas the pump just supplies pressure to the injectors which are operated by timing from the crank sensor through the ECM
talk with a specialist diesel shop as the pump pressure may be too low ( should be in the vicinity of 25,000 PSI)
run the fault codes
if it is not common rail then it could be more of an accelerator setting ( not getting full throttle ) or a governor problem
in any case it will require a special tool to set the timing so again talk with a specialist diesel shop

Oct 12, 2016 | Nissan Navara Cars & Trucks

1 Answer

What is torque settings for head bolts on Kia pregio 2001


What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

Aug 17, 2015 | Kia Cars & Trucks

1 Answer

P1330code is on reader how can I fix where do you start


This is an ignition timing code. It sets when the computer can't actively set the ignition timing properly. Most common cause on a Kia for this code to set is due to a bad throttle position sensor ( TPS). The computer doesn't recognize where the throttle is and therefore can't regulate the timing properly. It may not set a TPS code as this sensor can still be within operating peramaters yet slightly out of range.

Apr 07, 2015 | 2004 Kia Sedona

1 Answer

Do you need to power bleed a clutch for a 2004 pregio kia van


please post to KIA , not honda.
but is the same.
attach power bleeded to MC
set 1-2PSI
open bleeder valve at slave, let it run till no bubble and close.
dont let MC run dry
no different than brakes.

Aug 01, 2013 | 1996 Honda Accord

1 Answer

How to repair kia pregio alternator


i have converted my kia pregio alternator to recondition alternator for kia carnival problem is when i used all electrical such as aircon and light the alternator was not charging properly during traffic therefore when I need to turn off the engine i need to charge the alternator by pressing the gas for few minutes before turning off. please advice. thank you

Dec 16, 2012 | 2002 Kia Pregio

1 Answer

J2 kia engine timing diagram


timing marks for j2 KIA pregio

Oct 09, 2011 | Cars & Trucks

1 Answer

Hwo to fix the code p1330 for a Kia sorento 2004


Sounds like a shorted wire.. This is from a Kia forum on the subject:

The ECM computes ignition timing in response to the signals from several sensors. The timing is fixed during the start-up phase. However, when the engine has been started and the vehicle is driven away, the ECM computes the optimum timing based on the engine speed, load and temperature.The ignition timing is fixed BTDC 5 and DTC P1330 is set when connecting Ignition control terminal of Data Link Connector and ground. If disconnect Ignition control terminal of Data Link Connector and ground, the DTC is erased automatically.Make sure to check for short circuit to ground between Ignition control terminal of Data Link Connector and chassis ground when DTC is set.

May 20, 2011 | 2004 Kia Sorento

1 Answer

Kia Pregio missfire over 2500rpm, starts and runs perfectly


Generic problem for all Kia Rio Cars Kia Pregio missfire over 2500rpm

Dec 05, 2009 | Kia Rio Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...