Question about 2007 Toyota Yaris

1 Answer

The abs light stay on.What could be the problem because this problem started after the mechanic changed the left fron bearing and the hub thereof.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,976 Answers

Take it back to the mechanic and have him reconnect the sensor.

Posted on May 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Esc light and the abs light stay on in my 2007 hyundia santa fe


abs will be abs sensor is in hub bearing.next is the engine code?

Feb 26, 2013 | 2006 Hyundai Sonata

1 Answer

Our 2007 impala...the traction light and the ABS light stays on all the time..also we are having a roar sound with our tires as if they were snow tires, but they are not.The noise is loud.. any sugges


I would suspect you have a bad wheel hub (bearing) assembly. The bearings will roar/growl when they start to go bad. I've seen the bearings actually disappear from the hubs because it got so bad. Also, the ABS light will come on when the bearings go bad. I would take it to a mechanic before it gets any worse. BTW, GMs are known to have wheel hubs go bad.

I hope I was able to help you out.

Scott
ASE Certified Automotive Technician
ASE Certified MED/HVY Truck Technician

Jan 22, 2013 | 2007 Chevrolet Impala

1 Answer

IVE CHANGED MY AXLES LEFT AND RIGHT SIDE AND THE HUB WITH TH BEARING BUT THE MACHANIC IS TELLING ME TO CHANGE MY ABS ON THE FRONT DRIVER SIDE BUT MY LIGHTS NOT ON


Maybe they tested all the ABS Sensors
and you have a bad one

Why would you ask us ,instead of the people
who suggested replacing it?

Don't you ask questions, and even go into
the service bay, to see things first hand?

Better start doing that, or you will be taken
advantage of, or deal with mechanics that
know less than you do

Feb 17, 2011 | 1998 Acura CL

3 Answers

My 2003 mercury mountaineer ABS light is staying on. manually, the brakes work however they shimmy.changed the brake pads,checked the brake fluid and ABS fuse,bud when changing the pads,did now clean the...


I replaced the hub bearing assembly on drivers side twice and the light stayed on and the brakes worked fine. It was the wires (visible just above the tire on the frame) that rubbed against the frame that had shorted out. It was simply repaired and clip-stripped up out of the way. The light has been off every since then.

Dec 30, 2010 | 2003 Mercury Mountaineer

4 Answers

Impala - trac off and ABS light along with service traction syst


THE PROBLEM IS WITH A HUB WHEEL SPEED SENSOR OR MORE LIKELY THE HARNESS LEADING TO THE HUB.

CHECK THE RESISTANCE AT THE HUB CONNECTION, IT SHOULD BE BETWEEN 900OHMS AND 1300OHMS. THEN SWITCH TO A-C VOLTAGE, IT SHOULD BE 100MV WHEN TURNING THE WHEEL BY HAND. IF BOTH CHECK OUT THE PROBLEM IS IN THE WIRING TO THE HUB.

THE RIGHT FRONT HUB USUALLY HAS A BEND, DOWNWARD THEN UPWARD NEAR THE CONNECTOR TO THE HUB. THAT IS WHERE THE PROBLEM USUALLY OCCURS.

NEW HARNESS WIRES CAN BE BOUGHT AT THE DEALER.

Jun 14, 2009 | 2003 Chevrolet Impala

3 Answers

How to change front wheel bearing ford focus


You can do it yourself just take your time:
To change front wheel bearing.
1. Jack car up support with jack stands
2. take tire off
3. take caliper and brakes off
4. take rotor off
5. unbolt axle shaft nut at bearing hub
6. use a 3 lb slug with a block of wood
7. place wood on axle shaft and knock it in
8. back side 3 10mm bolts unbolt
9. front side have to pry off bearing hub Assembly only beacuse has dirt in knuckle hole.
10. clean hub knuckle and reinstall.
Its really not that hard or you could have them done for $900 and up. (I have changed alot of wheel bearing assemblies )Whats your e-mail I can send you a diagram if you want.

May 01, 2009 | 2004 Ford Focus

3 Answers

ABS error code 41 & 42


41 indicates Rpm sensor, at left front wheel, 42, is right front sensor. I'd check for dirt in and around both, clean connections, and wire brush or whatever the toothed ring to clean it all up, then clear codes & see what happens.

Apr 04, 2009 | 1993 Chevrolet K1500

2 Answers

Abs brake problem


I found my solution on the web a few years ago. My 2002 RVS had permanent ABS lights and no ABS.

It was suggested to check the ABS electrical connections at the brake disks . There are quick connects there and I found a corroded connector on the front passenger side. My wife started the RVS and put it in gear. With the brake pedal pressed, I wiggled the connectors and the ABS light went "off and on" right away. I replaced the connector and it never happened again. It is likely 4 years ago.

Worth a try.

Dec 28, 2008 | 2002 Buick Rendezvous

3 Answers

Buick rendevousz headaches


I own the 2002 Buick Rendezvous CX and I've encountered the same problems listed here. The ABS / Traction Control Lamp stays on and was throwing a code for the left wheel speed sensor as well as an anti-lock brake code (both in the wheel bearing hub assembly). I replaced the left and right front wheel hub assembly yet this did not eliminate the abs codes. 
Ultimately, I traced this problem to a break in the wire that leads to the left hub assembly. Although the sensor was properly connected, the wire (which is encased in a plastic housing) was broken. This is the wiring which leads from the abs wiring harness under the hood down to the left wheel abs sensor. 
I would suggest that you simply remove the left wheel and inspect the wire that leads to the abs sensor (there is only one wire on each wheel). Mine literally fell apart when I removed the plastic housing around the wire. I spliced the wire together and put it back in the plastic housing. After this, my abs codes disappeared and my anti-lock brakes began working again!
This is a simple fix that many people spend $1000 + on by replacing the hub assembly which does not fix the problem.

Aug 20, 2008 | 2002 Buick Rendezvous

Not finding what you are looking for?
2007 Toyota Yaris Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...