Question about 1989 GMC S-15 Jimmy

1 Answer

I have an 89' GMC Jimmy and the driver's and passenger door will not close. It won't even pull to. What should I do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 333 Answers

Sounds like the latch is in the closed position. does it bounce back open? Its like a hook latch, pull the door handle to open it and at same time pull the latch out. And it should move out and leave it open for the pin to go into it.

Posted on May 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 gmc sierra passenger side door won't latch.


check if the latch is in the closed position. If it is use a philips screw driver and place it under the latch and pull it put as you press the door handle.

Oct 02, 2014 | GMC Sierra Cars & Trucks

1 Answer

Dome light and key in ignition tone won't quit.


Yes, I would lean toward a stuck drivers door latch. Your door open switch is located in the latch itself and the ding is a reminder your key is in the ignition so you don't lock them in the vehicle when you lock the door. even though your door is shut, the truck still thinks it is open. sometimes spraying the latch with some WD-40 will get it freed up and working again, but a new latch might be in your future.

Apr 21, 2013 | 1997 GMC Jimmy

1 Answer

O2 sensor


not exactly sure, but i have an 89 chev pickup and a 94 gmc and they are both on the exhaust manifold or even on the exhaust pipe near the manifold. hope this helps

Jan 04, 2013 | 1993 GMC Jimmy

2 Answers

Power window switchs on 1996 gmc jimmy


Inspect or replace the window lock and unlock switch on the drivers door power window switch. There is a lock and unlock switch that will disable the switches to the other power window in the Jimmy. Check to make sure that switch is in the unlock position to have the other power window switch to work.
Thank you for suing fixya and good luck.

Apr 19, 2010 | 1996 GMC Jimmy

2 Answers

Jimmy electrical burning.


The wire has rubbed somewhere and is shorted to ground. Replace the wire from the door switch to the light, replace the fuse with one of the correct amperage and it should work. Disconnect the battery while you are replacing the wire.

Jan 06, 2010 | 1999 GMC Jimmy

1 Answer

How do i bleed the brakes on my 1998 gmc jimmy


it takes two people to do, one to pump and hold the brake peddal and one to open the bleeders....

One person pumps the peddal 5-6 times and holds, while the other starts at the Passenger rear tirer and opens the bleeder valve till the brake peddal hits the floor, and close it, do this till no air comes out but only fluid, then go to Drivers Rear, then Passenger Front, then Drivers Front.....

DON'T open the vlave while they are pumping, or allow them to let up on the peddal till you have the vlave closed again, as that will put air back into the system.

If you have any other probs, or questions, email me at dswenk@live.com

Sep 14, 2009 | 1998 GMC Jimmy

1 Answer

My 2000 Jimmy window switch on the drivers side does not work for the passenger and driver side windows? What should I do or replace?


if the drivers side switch is the only one that doesnt work it needs replaced confirm by making sure the passenger door switch works the passenger window

Jun 21, 2009 | 2000 GMC Jimmy

2 Answers

How do I remove interior front door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then just remove the bolts for the mirror

May 16, 2009 | 1997 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...