Question about 2006 Chevrolet Aveo

1 Answer

Engine light comes on and engine stalls but restarts and runs fine the code is for camshaft sensor changed that and still does it disconnect the battery to clear engine light anybody have any answers

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,826 Answers

Clean th reluctor on the camshaft,it may have metal sticking to it,or the timing chain,or belt is stretch

Posted on May 11, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What are the probable causes of camshaft sensor DTC?


Camshaft sensors do go bad. They can go bad slowly, so you don't notice the badness until your engine stalls, but restarts, or you get a "check engine" light. They are not expensive or hard to replace.

Nov 10, 2015 | 1999 Isuzu Rodeo

1 Answer

2001 ignis gl manual overhreating


Camshaft position sensor. I had the exact same problem. I changed it and it never stalled again.

Dec 18, 2013 | 2001 Suzuki Swift

1 Answer

I have a p1361 problem with car dying and stalling and also a 1456 code any guesses light went off and car runs ok now


P1361 Camshaft Position (CMP) Sensor A (Top Dead Center (TDC)
Possible causes:
- Camshaft position sensor. Replace.
- Signal wire open or shorted to ground.
- ECM.
P1456 Evaporative Emissions (EVAP) Control System Leakage (Fuel Tank System)
- Always fill in the fuel with the engine switched off.

Apr 01, 2013 | 2001 Honda Civic

2 Answers

1994 jeep engine stall code 11


The 4 cyl and 6 cyl engines use a distributor, so no crank and cam sensors.
There is a pick-up coil in the bottom of the distributor that could be failing.
Code 12 means the battery has been disconnected or the ECM has lost power since the last scan.

Jun 27, 2012 | 1994 Jeep Cherokee

2 Answers

Toyota ipsum 2002 check light comes on with code P1346.


Definition of Diagnostic Trouble Code P1346 Audi: Ignition Coil Power Output Stage 3 Short to B+ BMW: Misfire During Start Cylinder 3 Buick: Intake Camshaft Position [CMP] Sensor System Performance Cadillac: Intake Camshaft Position [CMP] Sensor System Performance Chevrolet: Intake Camshaft Position [CMP] Sensor System Performance Ford: Fuel Level Sensor B Circuit GMC: Intake Camshaft Position [CMP] Sensor System Performance Lexus: VVT Sensor Rang/Performance Problem (Bank 1) Lincoln: Fuel Level Sensor B Circuit Mazda: Fuel Level Sensor B Circuit Mercury: Fuel Level Sensor B Circuit Oldsmobile: Intake Camshaft Position [CMP] Sensor System Performance Pontiac: Intake Camshaft Position [CMP] Sensor System Performance Saturn: Intake Camshaft Position [CMP] Sensor System Performance Toyota: VVT Sensor /Camshaft Position Sensor Circuit Range/ Performance Problem (Bank 1) Volkswagen: Ignition Coil Power Output Stage 3 Short to B+

Mar 12, 2010 | 2001 Toyota Sienna

1 Answer

I have a 2000 buick lesabre. The fix engine soon


It NEVER was the camshaft sensor! Unless, you've removed the engine lately, which I doubt.
RUN to Advance Auto Parts and buy a can of "SeaFoam" and add to your gas tank per instructions...drive at least 100 miles and the problem should go away...IF it doesn't you'll have to replace the O2 sensors in the exhaust system...Any good mechanic should be able to do this for much less $$ than the dealership DO NOT go to the dealer for repairs!
Good Luck

Jun 22, 2009 | Buick LeSabre Cars & Trucks

2 Answers

2002 miata ls driving @ 80 mph engine stalls dies let set for 10min restarts and runs fine gives obd2 code p0340 camshaft sensor


I have had the same problem on my 2000 Miata. Turned our it needed a new cam sensor. Had it replaced 9 months ago and now it has occurred again. They are replacing the cam sensor again.

Mar 18, 2009 | 2000 Mazda MX-5 Miata

1 Answer

F350 2000 stalling and sputtering while driving after running a while or runs fine


Many possibilities:
Is it a Diesel?
Camshaft position sensor recall may cover it.
Gas or Diesel:
Fuel Pump and/or relay.
Fuel Filter.

Engine codes could help if Check Engine Light is on.

Jul 08, 2008 | 2000 Ford F350 Super Duty Super Cab

Not finding what you are looking for?
2006 Chevrolet Aveo Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...