Question about 2004 GMC Envoy

1 Answer

The rear window has two wires that are attached to glass, with a metal square in a copper colored square on glass . one of them is off. how can I re-attach it?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 834 Answers

You can repair it with a "Rear Window Defroster Repair Kit" that you can get from just about any auto parts store.

Posted on May 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a back glass in a 05 dodge magnum wagon. The back lid glass


If you would please look at the glass and the metal door in which it attaches, I believe you will see there is a black "tar" that holds it in place.
First, disconnect the electric rear window defroster wire, if you have one.
You would, using a very thin steel wire, separate the glass from the "tar".
Then, clean the tar out of the channel, and prepare the rear door for new tar and the new glass.
It sticks on.

Nov 09, 2015 | Dodge Cars & Trucks

1 Answer

How do i attach tio window the Rear view mirror ?


The mirror attaches to the inside of the windshield using a small metal "button" that is glued to the glass. The mirror assembly slides onto the button, and is secured with a set screw.

If the metal button comes off of the glass, you will need to re-attach it. Autoparts stores sell glue kits specifically made for this purpose. Make sure the glass and button are completely clean before starting (I like to wipe them both with a little rubbing alcohol to make sure there is no grease or oil on them as well), and follow the directions on the glue kit's package.

If the metal button is missing, you may be able to find one at the same auto parts store where you find the glue. If not, check with any GM dealership's parts counter.

If there are also other issues with the windshield glass, you can get the entire windshield replaced by a glass company. The new windshield will come with the button already installed. Your auto insurance may cover the cost of the replacement (check with them first).

Jul 07, 2014 | 1998 Chevrolet Blazer

1 Answer

Cable system on passenger door power window, 1999 dodge Caravan, has slipped off track. Need exploded diagram to restore to original.


REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel


DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Sep 02, 2012 | 1997 Dodge Grand Caravan

1 Answer

The little spade lug that is attached to the rear window glass on the rear Pass. side is missing. The wire is there to attach to that lug. Can you attach a new lug to the glass somehow?


You can fashion a lug, but it needs to be tight in the connector, and flat and clean where it attaches to the window. Permatex makes a glue with copper in it just for this, any auto parts store should have it. I woul dattach the connector to the wire and then glue it, you want to have it perfectly clean, like with scothbrite where it attaches.

Dec 18, 2009 | 2000 Dodge Neon

1 Answer

How get replacement rear vent window into place? its a 1995 maxima passenger side rear vent window.have picked up a new one from salvage and fear if i force it, it may shatter.


The metal glass run between the vent & doorglass has a phillips screw at the top under the door weatherstrip. I usually remove that screw, with the doorglass down & glass run (felt) pulled down at the top just enough to allow the metal part to move as you force the ventglass into place. lube the vent gasket with silicone spray or any good wet lubricant and force the glass in, bottom 1st. If this makes you too anxious, remove the 10 mm attachment that retains the metal glass run at the lower end of the part. To get to it, you will have to remove the door panel. Good luck

Sep 27, 2009 | Nissan Maxima Cars & Trucks

1 Answer

Put new window motor and switch and passenger side still doesnt work on my 2002 tahoe


Check the power Window Relay Fuse which should be located in the engine compartment relay fuse box. This fuse is a bigger square or rectangle with a black plastic or metal looking case. unlike the tiny colored plastic glass looking type you see in the inside fuse panel

Jul 01, 2009 | 2002 Chevrolet Tahoe

2 Answers

How to reattach a rear view mirror on 2009 Audi A6


Go to a local window-tint shop and ask them NICELY to look a t it..then buy them lunch $10
Good Luck

Jun 15, 2009 | 2000 Audi A6

1 Answer

Window regulator replacement


Window Regulator, Rear Door, Explorer Removal
  1. Remove the rear door trim panel and watershield. Refer to Section 01-05B .
Trim Panel, Rear Door, Explorer, Hi-Series Four-Door Removal and Installation
  1. Remove the two screws retaining the rear door trim panel (27406) located above the door handle.
  1. Remove trim cup at the door handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator switch plate (14524) , use notch located at lower end of plate using a screwdriver to lift and remove.
  1. Remove window regulator switch plate from rear door trim panel pulling wire harness from rear door trim panel .
  1. From bottom of window regulator switch plate , remove two screws and disconnect connector from window regulator control switch (14529) .
  1. At each plastic clip location, pry the rear door trim panel away from the door inner panel using the door trim panel removing tool from Rotunda Moulding/Trim Kit 107-00401 or equivalent.
  1. Remove panel, lift slightly to remove flange at the top of rear door trim panel from trough in the glass weatherstrip. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the rear door trim panel to the door inner panel, firmly loading clips into slots provided on rear door trim panel .
    33c9359.gif
  1. If equipped with power windows, disconnect the wire from the regulator.
  1. Remove the rear door window glass as described in this section.
  1. Remove the window guide, if equipped, (nuts and washers). Remove guide from door belt opening.
  1. Remove three 1/4-inch rivets attaching motor bracket (electric) to inner panel and two 1/4-inch rivets attaching regulator lower bracket to inner panel. Use drift punch to knock out center pins for each rivet. NOTE: Use care not to enlarge sheet metal holes in the door inner panel when drilling.
  1. Using a 1/4-inch diameter drill, drill out the remainder of the rivet.
  1. Remove two upper regulator attaching nuts.
  1. Remove regulator from the front door (20125) .
Installation
  1. Lubricate regulator mechanism with Multi-Purpose Grease D0AZ-19584-AA or equivalent.
  1. Install regulator into access hole in inner panel.
  1. Position regulator using upper regulator studs and tabs on motor mounting bracket (electric) or cup mounting plate (manual).
  1. Install rivets attaching regulator to door inner panel (1/4-20 x 1/2-inch bolt and 1/4-20 nut and washer assemblies or equivalent metric fasteners may be used as alternates).
  1. Install two upper regulator attachment nuts.
  1. Install door glass as outlined under Door Glass Installation.
  1. Adjust glass as outlined under Adjustments .
  1. Reconnect wire to regulator, if equipped.
  1. Check operation of window regulator.
  1. Install door watershield and trim panel. Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

2 Answers

Rear window regulator broke


The regulator is attatched to the glass using the rivets through plastic disks. You need to drill them out before the glass can be removed.Save the plastic parts for reassembly.Good Luck

Aug 25, 2008 | 2002 Ford Explorer

2 Answers

Left rear window stuck down. Hear motor working but doesn't lift the window.


For a Temp fix take it to a local glass tint shop and ask them to wire it up for you so people cant steal it. But the cable broke or the metal clamp that attaches to the bottom of the glass came off (if thats the case get some plumers goup or any other glue that stays flexible when it drys and try glueing it back to the bottom of the glass) I have a 97 Lincoln Presidental TC that happen to both my rear windows and I was able to glue the assimbaly back together for a quick fix, good luck

Jul 24, 2008 | Lincoln LS Cars & Trucks

Not finding what you are looking for?
2004 GMC Envoy Logo

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...