Question about 1999 Ford Explorer

1 Answer

How do I reset the remote door unlock code? - 1999 Ford Explorer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,970 Answers

For "delete" your personal code, first be sure that you have the factory keypad code...

1. Enter the factory set 5-digit code.
2. Within five seconds, press the 1 - 2 on the keypad and release.
3. Press and hold the 1 - 2 for two seconds. This must be done within five seconds of completing Step 2

All personal codes are now erased and only the factory set 5-digit code will work.

Hope this help (remember comment and rated this help).

Posted on May 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

As2501 remote


use a code reader to reset the CPU and test from there.

Jan 23, 2014 | 1998 Toyota Sienna

1 Answer

2001 maxima alarm not working but panic works


ck for a fuse in the under the hood fuse box that says bsm may be blown.
Also try this.....
To reset the security system remove the negative battery cable for 30 minutes, then reconnect the cable. Next, lock and unlock the doors using the remote. This will reset the alarm system and the engine will start and fobs reset.

Here are some factory notes....FYI

Anti-Theft Systems

PROGRAMMING

NOTE: If a new Smart Entrance Control Module (SECU) is installed, a new identity code must be entered and all remote controllers must be programmed. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.

PROGRAMMING > PROGRAMING NEW ID CODE

NOTE: This procedure will erase all previous identity codes and render all previously programmed remote controllers inoperative (until reprogrammed). All remote controllers to be used with system must be programmed at the same time. A maximum of 4 remote controllers can be programmed. Any attempt to program more than 4 controllers will be ignored. If same identity code is entered more than once, entry is ignored even though hazard warning lights will still flash twice.
1. Close and lock all doors. Erase original identity code(s) by inserting and completely removing key from ignition switch more than 6 times within 10 seconds. Hazard warning lights should flash twice. Turn ignition switch to ACC position.
2. Push any button on new remote controller once. Hazard warning lights should flash twice, indicating identity code has been entered. If identity code cannot be entered, repair multi-remote system. See appropriate MULTI-REMOTE CONTROL SYSTEMS article.
3. For each additional remote controller to be programmed, manually release door lock and lock again by using door panel switch and repeat step 2. If no additional remote controllers are to be used, exit programming mode by unlocking and opening driver's door.

Please let me know if you need anything else to get the problem fixed. Happy mew Year!

Jan 03, 2018 | 2001 Nissan Maxima

1 Answer

All my remotes won't unlock passenger doors, why?


this is a problem that can appear after your car battery died, cause the car didn't reset propely, so taking the battery out and putting it back in or letting your car die again would do the trick. I tried a lot of reprogramming procedured for my remote key, none of them worked, what did the trick though was simply unlocking the doors via the all door unlock button on the passenger side door, so simple.

Apr 27, 2012 | Cars & Trucks

1 Answer

Remote won't lock or unlock doors


You either need to replace the battery(s) or reset the codes which should be in your owners manual

Apr 13, 2012 | 2000 Mercedes-Benz M-Class

1 Answer

I locked my keys in my 06 mercury mariner and i need to reset the code to my car, how can i reset the code?


You must have all remote entry transmitters (maximum of four) available before beginning this procedure. According with the Mariner Owners Manual check this procedure to reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked.
2. Put the key in the ignition.
3. Turn the key from the 1 (LOCK) position to 3 (RUN).
4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN).
Note: The eighth turn must end in the 3 (RUN) position.
5. The doors will lock, then unlock, to confirm that the programming mode has been activated.
6. Within 20 seconds press any button on the remote entry transmitter.
Note: If more than 20 seconds have passed you will need to start the procedure over again.
7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed.
8. Repeat Step 6 to program each additional remote entry transmitter.
9. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters.
10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Note: If all remote entry transmitters are not present during the programming procedure, the missing transmitters will not work with the vehicle following programming.

Hope helps.

Sep 07, 2011 | 2005 Mercury Mariner

1 Answer

The back door won't unlock or open and the front doors won't unlock by the remote


Simple enough to reset the power locking system:
1) make sure battery in remote is good, if in doubt replace it. Next unlock all the doors and keep them closed.
2) Jack up the car and you'll find the power lock reset button above the fuel tank. If you cant reach it drop the tank down slightly until you are able.
3) Depress the power lock reset button, then get inside the car and hold the unlock button on the remote for 2 min.
4) The system will reset when you get out of the car and hold the lock button for another 2 min while circling the car briskly.

Jul 02, 2010 | 2002 GMC Safari

1 Answer

How do you re-program the security code on a 2007


FORD KEY PADS
  • Enter permanent factory code
  • Press the 1/2 button within 5 seconds to enter programming mode
  • Within 5 seconds enter new code, doors will lock, unlock to verify code, this erases previous codes remotes will also need to be programmed. (MAYBE)
KEY PADS/REMOTES
  • Insert key, turn ignition off-to- on eight times in succession, ending with key in on position doors will lock, unlock to verify in programming mode
  • Press any button on new remote, doors will lock, unlock to verify
  • Do the previous step with the second remote, doors will lock unlock to verify.
  • Turn ignition off. Doors will again lock, unlock to verify.
NOTE-Some vehicles use 5 turns of the key instead of 8

Jun 05, 2010 | 2007 Ford Explorer Eddie Bauer

4 Answers

Passlock


turn key all the way on (not to start) let set for 1 hur cycle key and try it.

Jul 20, 2009 | 1999 GMC Jimmy

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Keyless remote


Disconnect the battery from your car (negative cable only) overnight. Make sure you have your radio reset code before doing so.

Then reconnect after 10 hours, and make sure you have remote handy as alarm may go off. Then if that doesnt fix it, go to driver door, then insert master key, pull up on handle first all the way and hold it. Then turn the key slowly all the way so the doors unlock and continue turning the key. This will reset the central locking system as yours may have gotton stuck. then remove key let go of handle, open door and try to lock and unlock doors from switch inside car.

Then try remote. It should work, this is what the dealer will do and charge you about $350...if it doesnt work order a new remote b/c yours may have become damaged by liquid or dropping?

Have a great day,

Thanks,

Mark

Dec 30, 2008 | 1998 BMW Z3 Roadster

Not finding what you are looking for?
1999 Ford Explorer Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...