Question about 1996 Dodge Ram 1500 Club Cab

1 Answer

How do i no if my torque converter is going bad

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Dodge Master
  • 14,036 Answers


Posted on May 11, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What are some of the signs that my Torque Converter is going bad in my 2006 Acura RL???

rattling noise in bell housing
lack of drive or acceleration overhaeting the transmission oil
try explaing the type of noise you have or the symptoms you have as it may not be a converter if it is not moving but a torque converter clutch solenoid /servo

Apr 28, 2015 | Acura Cars & Trucks

1 Answer


The two most common failures in torque converters are excessive slipping due to bad seals and locking problems. If the torque converter is slipping, you will have poor acceleration, but the engine will rev up quickly. It is especially noticeable on hill climbs; engine RPM will be high, but the vehicle does not go as fast as it should, and in severe cases may not be able to climb the hill.

Lockup problems may be harder to detect. At highway speeds, most modern torque converters have a locking mechanism to eliminate slip. Failure to lock may not be noticeable except as a decline in highway fuel mileage. Failure to unlock is readily apparent; the engine may stall on deceleration, or hard braking is required to slow the vehicle, which then stalls.

Mar 11, 2015 | 1996 Ford F150 Regular Cab

1 Answer

Torque converter making noise

drop off the cover under the torque converter and inspect the flex plate that the converter is bolted to. look for cracks in the plate around the bolts . undo the bolts and move the torque converter back towards the gear box and look for cracks around the flywheel bolts.. If all ok then do everything up and have a pressure test done on the transmission to check for internal mechanical failure. Have this done at an accredited auto transmission shop ( not the local mechanic) and as him what the results are and the possible solution. Remember to ask how much to fix the problem parts before you accept that it needs a new box

Jan 11, 2014 | 2004 Lincoln LS V8

1 Answer

My 2001 ford taurus lost all power while driving down the highway. Their were no sounds of breaking or shattering of the gears but when I got the car stopped I had no gears left. I lost every gear from...

these cars have a major issue with torque converters.... the torque converter input splines are softer than the splines on the input shaft and it sheers the teeth off of the input side of the torque converter, i have replaced a ton of these for this problem... usually when you replace the torque converter every thing goes back to normal, what you need to do is check the fluid level while the engine is running, if the fluid level is really high than that is what happened because the torque converter failed and drained all the fluid into the pan... to fix it the transmission will have to come out and the torque converter will need replaced if you drain all the fluid out of it and look down into the center of the torque converter with a flash light you will see the splines missing...

Jun 05, 2011 | Ford Taurus Cars & Trucks

1 Answer

2004 Honda Civic automatic transmission, will not shift, stays in first gear.

change the tranny fluid (hava a shop do it, you cannot do it yourself) and filter, and have them look for metal shavings in the drained fluid- this would signify a tranny going bad, or one that already has gone bad. the filter could simply be clogged, the fluid could be excessively dirty, or, worst case scenerio, the torque converter could be on its way out or completely shot. sometimes a torque converter that is about to go bad can be used for several more months after a fluid change, and sometimes the fluid change will not help the problem. it all depends on how far gone the torque converter is.

Mar 26, 2011 | 2000 Dodge Grand Caravan

1 Answer

Transmission wont go into drive it only goes in reverse

you may have a Bad torque converter.well you should hope it is only your torque converter and not a bad transmission.

Mar 17, 2011 | 1998 Ford Taurus

1 Answer

1984 chevy 1/2 ton pick-up either 350 or 400 trans dont know which reverse gear works but no 1,2,3 seems to try to move but wont

Sounds like you need a new transmission. It can only be one of two things: Transmission is old and needs replaced or the torque converter is bad. But if your going to replace the torque converter you might as well make sure you have a good transmission because you have to drop the transmission to get to the torque converter. No point in droping the transmission and replacing the torque converter to find out you need to drop it again because the transmission is bad. You should be able to drop the transmission is a few hours. You only have 3 bolts on the fly wheel and one bolt for the transmission mount and about 6 bolts connected to the engine. Then you have your fluid lines speedometer cable and drive shaft. And your dip stick.

Feb 04, 2011 | Chevrolet C1500 Cars & Trucks

1 Answer

Service engine soon light had car scanned came up tcc transmission control circuit switches gears fine

this could be a bad torque converter solenoid, or a bad torque converter and/or the wiring going to and in the transmission. further diagnostics should be done with a scanner

Aug 27, 2010 | 2003 Cadillac Sts

1 Answer

Runs fine but will not go in any gear

I had that happen on a 1998 Taurus with about 80,000 miles. It turned out the "Torque Converter" was bad. There's a small splined shaft that drives the oil pump in the transmission, those splines shear off in the torque converter and the pump quits turning. An easy way to tell is check the transmission fluid level with engine off it should be over full. Now start the engine did the fluid level go down to about the full mark or did it stay high? If it stayed high the pump is not turning, the good news is you probably only need a torque converter the bad news is the trany has to come out of the car to change it.

Jan 05, 2010 | 2003 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides