Question about 1990 Plymouth Grand Voyager

1 Answer

I need advice on how to get the ignition switch out to replace it

Posted by on

Ad

1 Answer

Greg Bernett
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    Superstar:

    An expert that got 20 achievements.
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 2,984 Answers

Hope this helps you! Please don't forget to rate....thanks!!


I need advice on how to get the ignition switch - c025733.gif
Ignition switch installation-1984-90 models


  1. Disconnect the negative battery cable.
  2. Remove the steering column cover.
  3. If equipped with automatic transaxle, position the gear selector into DRIVE and disconnect the indicator cable.
  4. Remove the lower panel reinforcement.
  5. Drop the steering column for switch replacement.
  6. Disengage the wiring connector from the ignition switch.
  7. Position the ignition lock cylinder into the LOCK position.
  8. Tape the ignition switch rod to the steering column to prevent the rod from falling out of the lock cylinder assembly.
  9. Remove the screws attaching the ignition switch to the column jacket.
  10. Remove the ignition switch by rotating the switch 90 degrees and pulling up to disengage from the rod.
To install:
  1. Rotate the switch 90° and push down to engage the rod.
  2. Install the screws to the ignition switch mounting plate but do not tighten.
  3. Remove the tape holding the rod to the column.
  4. Adjust the switch by pushing up on the switch to take up rod system slack. This must be done with the key cylinder in the LOCK position and the key removed.
  5. Tighten the screws attaching the switch to the column.
  6. Connect the wiring connector to the ignition switch.
  7. Install the steering column.
  8. Install the steering column cover.
  9. Connect the negative battery cable.

Posted on May 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

6ya.com

6ya - Get Instant Help

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I change my ignition switch on my 2005 Impala and it won't start now what could be the problem.
did you also change the immobiilizer , there should be a trandponder in the key that was coded to the ignition switch. The switch will need to be coded to the car I believe? You need the advice of an auto locksmith really, even if you get advice here the work will only be do anle by a professional .
Good Luck
Theyse modern cars can be very complex.

Jun 03, 2015 | Cars & Trucks

1 Answer

Lost my keys,then I broke my ignition please help I need to hot wire there are 6 wires which
I hope you are only doing this temporarily. Generally speaking, ignition 1&2 would become powered when key is turned to on position. These could be wired to toggle switches. Highly recommend a high amperage momentary contact switch only for the starter lead. Best advice is the get a new ignition switch rather than mess with wiring. Doing so could do un repairable damage to your ignition system, wiring harness, and computer

Oct 03, 2014 | 1990 Toyota 4Runner

1 Answer

Bypass ignition switch/antitheft
Check with your local lock smith, most of them cam reprogram your PATS system. Buy an ignition switch with keys from an autoparts warehouse or online but make sure that the one you order hase PATS keys. the description should not " programming required" You will have to have 2 keys.

Dec 18, 2013 | 1997 Lincoln Mark VIII

1 Answer

Starter or ignition switch
It's either your ignition switch or ignition switch wiring, lines for the starter relay is short circuited at some point and it keeps the starter running, ALSO it might be a stuck starter relay, so it helps changing the starter relay first and then if the problem still exists have the ignition wiring and ignition switch checked. Hope it helps and comment if you need more advice. Please don't forget to rate the answer it helps me with my ratings. Thanks!

May 07, 2010 | 2002 Chrysler Town & Country

2 Answers

1993 Buick Skylark Ignition Switch is very lose. When turning the key, it goes all the way forward, and nothing happens. You have to jiggle the key in order for the car to turn over. Do I need to replace...
Yes, a loose ignition switch makes contact more difficult. The ignition switch needs to be flush in order to make perfect contact.

Sep 04, 2009 | 1993 Buick Skylark

1 Answer

I have to giggle the key to get the ac fan to come on. 2003 dodge
IF you have done it before you will be fine,Its like riding a bike.You have good common sense so just do it.

Aug 10, 2009 | 2004 Dodge Ram 1500

1 Answer

Rajak2009's reply: replace ignition cylinder. how to take it out
well you can try using a very small paper clip or the like and try to pry it out or you'll have to remove the ignition switch. a haynes auto repair manual at any auto parts store for 17$ will explain in detail.

Jul 01, 2009 | 1992 GMC Sonoma

4 Answers

2002 sonata steering ignition lock up
try to push the car back and forth few times....your steering/ignition lock will be released.

Dec 20, 2008 | Hyundai Motor 2002 Sonata

1 Answer

Rplacing the ignition switch
there is a safety switch that prevents the ignition from being turned off and removed while in gear. try putting in nuetral and removing the key. if it does then it is a problem with the shifter and not the ignition.

Nov 30, 2008 | 1997 Chevrolet S-10 Pickup

1 Answer

Rplacing the ignition switch
You will need to remove the steering wheel. Then you will need to use a steering wheel lock remover to remove the lock plate. This can be purchased at most auto parts stores for 20 to 40 dollars. Next you should be able to remove the retaining screw in the ignition switch( be careful not to drop the screw in the colum housing). You may have to work the key back and forth to get the old switch out. Just repeat this process in reverse to install the new key switch.

Jun 30, 2008 | 1992 Chevrolet S-10

Not finding what you are looking for?

View Most Popular

1990 Grand Voyager

  • Cars & Trucks

Related Question

I change my ignition switch on my 2005 Impala and it won't start now what could be the problem.

  • Cars & Trucks

Open Questions:

0 Answers

a fuse diagram for a 1990 plymouth grand voyager

Apr 05, 2014 | 1990 Plymouth Grand Voyager

0 Answers

fuel pump relay

Mar 14, 2014 | 1990 Plymouth Grand Voyager

0 Answers

Serpentine Belt Layout, 1995 Grand Caravan 3.0 L

Feb 17, 2014 | 1990 Plymouth Grand Voyager

0 Answers

location of fuel pump relay on 1990 plymouth grand voyager

Sep 15, 2012 | 1990 Plymouth Grand Voyager

See all 1990 Plymouth Grand Voyager Questions

Related Topics

1990 Plymouth Grand Voyager Logo

405 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1996 Plymouth Grand Voyager

1996 Plymouth Grand Voyager

1997 Plymouth Grand Voyager

1998 Plymouth Grand Voyager

Plymouth Grand Voyager Cars &...

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...