Question about 1988 Ford F 250

1 Answer

What regulates fuel air mixture. my fuel rail

What regulates fuel air mixture. my fuel rail presure is 38psi. running very lean in all cylinders. engine lite not on. compresson close to 150psi in all cylinders. starts fine-idies fine but on road it starts missing and gets worst the more throttle you give it- full throttle is like a potatoe is in exhaust. exhaust seems open.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

The oxygen sensors trim and richen the fuel air mixture and they will not always set a code in obd1 vehicles. could be a stopped up cat though if the exaust smells like rotten eggs

Posted on May 11, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cylinder 1 misfire detectedrich or lean air/fuel mixture fuel injecter fault and faulty crank shaft sensor


Wow... Thats a lot of diagnostic codes. First... The cyl #1 misfire will cause the Engine to run rich giving you a rich running engine. Therefore the rich lean code. This misfire on cyl #1 can also throw a crankshaft sensor code as it will slow down engine rpm. I would change the spark plug and ignition coil to cyl#1 and have the codes erased and see if that solves the problem. If not, you then need to persue any codes that may reappear.

Jun 06, 2015 | 1999 Kia Sephia

1 Answer

Black smoke from exhaust


Black smoke is an indication of too much fuel-running rich-in the cylinders. The air/fuel mixture is way off-too much fuel. Possible causes are cylinder misfires (runs and idles rough, a noticeable miss), leaking fuel injectors, or a failed fuel pressure regulator.
Take off the vacuum line to the regulator (on the fuel rail?)-if there is evidence of gas in the vacuum line, the regulator has failed and excess gas is being sucked into the engine through the vacuum line.

You should take a fuel pressure reading to check pressure against the specification for your car.
Also possible that the fuel metering is correct, but the air being supplied to the cylinders is lacking. A clogged air filter could cause that, but you would also experience a rough running condition. Since you didn't mention that, I would think the fuel metering is wrong-too much gas.

Apr 10, 2014 | 2006 Peugeot 604

1 Answer

Po171&po191on audi a4 2007


P0171 indicates the system is running too lean (too much air, not enough fuel). P0191 indicates a problem with the Fuel Rail Pressure Sensor Circuit Range/Performance. Low fuel rail pressure could cause the Lean condition. Replace the fuel rail pressure sensor, and you'll probably correct the lean mixture error. Clear the codes and drive it to see if codes re-occur. Good luck.

Sep 29, 2013 | Cars & Trucks

1 Answer

I have a 1999 chevy malibu - 45000 mi. Took to auto zone for computer reading and replaced O2 sensor that the dealer replaced with the fuel filter. about 145 miles while accelerating up a moderate hill...


The 02 sensor is detecting a malfunction in the emissions. That would be from a bad fuel mixture, too rich or too lean caused by dirty or faulty injectors or MAF sensor. A clogged catalytic converter will also cause it. Connect a manual fuel gauge to the fuel rail and test your fuel presuure. Test your fuel pressure regulator, the fuel pressure should increase 5-10 pounds when you disconnect the regulator...if it don't, the regulator is bad...Check for vacuum leaks and stuck or dirty egr valve. This would cause a lean condition. Check your air filter. Good luck, i hope this helps.

Jul 17, 2011 | 1999 Chevrolet Malibu

1 Answer

Rough idle vibrates and po171 code service engine soon. jamesrowland9@aol.com


Hi, a Ford P0171 is a LEAN code for cylinder bank 1, and P0174 is a LEAN code for cylinder bank 2. These codes commonly occur on many Ford vehicles, and are set when the powertrain control module (PCM) sees the air/fuel mixture is running too lean (too much air, not enough fuel).
When the Check Engine Light comes on, either one of these codes, or both, may be found when a code reader or scan tool is plugged into the vehicle diagnostic connector. IF the vehicle is driven long enough, typically both codes will be set.
A P0171 lean code for bank 1 is the cylinder bank on the RIGHT (passenger) side of the engine on Ford vehicles with a V6 or V8 engine and rear-wheel drive.


A lean fuel condition may exist if the engine is sucking in too much air and/or the fuel system is not delivering enough fuel. If bad enough, a lean fuel condition may cause lean misfire, a rough idle, hesitation or stumble when accelerating, and/or poor engine performance.
Unmetered air can enter the engine through a vacuum leak, a dirty airflow sensor that is not reading airflow accurately, an EGR valve is not closing and is leaking exhaust into the intake manifold, an EGR valve that is allowing too much flow (because the EGR differential pressure sensor that monitors EGR flow is faulty and is under-reporting EGR flow).
If the problem is not enough fuel, the underling cause may be a weak fuel pump, restricted fuel filter, leaky fuel pressure regulator or dirty fuel injectors.

Mar 24, 2011 | Ford Escort Cars & Trucks

1 Answer

2000 Silverado 1500: location of fuel presure regulator...


The regulator is on the fuel rail on the driver side of the motor. Look for a vacuum line that plugs into the top of the regulator. If you suspect yours is bad, with the engine shut off pull the vacuum line off. If gas runs out then the regulator is bad.

May 16, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

Have replaced about all relays and sensors plugs and wires fuel pumps egr valve and solenoid eec relay tps sensor air charge sensor o2 sensor coolant sensor have in my hand knock sensor havent put in yet...


i think i would check the fuel presure regulator and the fuel presure if fuel presure low look at fuel filter if rail not holding presure then look at fuel presure reg and vac conection on it

Jan 23, 2010 | 1986 Ford Ranger 2WD

1 Answer

My 1997 hyudai accent has a missfire code on cylinders 1 and 4 car has no power replaced plugs only change is the idle is much smoother. what else should i check


Main causes of misfire would be loss of spark; the air/fuel mixture is too far out of balance to ignite; or loss of compression.

Loss of spark includes anything that prevents coil voltage from jumping the electrode gap at the end of the spark plug. Causes include worn, fouled or damaged spark plugs, bad wires or even a cracked distributor cap. A weak coil or excessive rotor gas inside a distributor would affect all cylinders, not just a single cylinder.

"Lean misfire" can occur when the air/fuel mixture is too lean (not enough gasoline in the mixture) to burn. This can be caused by a dirty, clogged or inoperative fuel injector; air leaks; or low fuel pressure because of a weak pump, restricted filter or leaky pressure regulator.

Loss of compression means the cylinder loses most of its air/fuel mixture before it can be ignited. The most likely causes here are a leaky (burned) exhaust valve or a blown head gasket. If two adjacent cylinders are misfiring, it's likely the head gasket between them has failed. Also, if an engine is overheating or losing coolant, it's likely the head gasket is the culprit.

You can isolate the weak cylinder by temporarily disconnecting each of the spark plug wires, one at a time, while the engine is idling. When there's no change in the idle speed, then you have pinpointed the weak cylinder.

Aug 25, 2009 | 1997 Hyundai Accent

1 Answer

Engine light has come on and car is misfiring, loss of power, sounds rough


Main causes of misfire would be loss of spark; the air/fuel mixture is too far out of balance to ignite; or loss of compression.

Loss of spark includes anything that prevents coil voltage from jumping the electrode gap at the end of the spark plug. Causes include worn, fouled or damaged spark plugs, bad wires or even a cracked distributor cap. A weak coil or excessive rotor gas inside a distributor would affect all cylinders, not just a single cylinder.

"Lean misfire" can occur when the air/fuel mixture is too lean (not enough gasoline in the mixture) to burn. This can be caused by a dirty, clogged or inoperative fuel injector; air leaks; or low fuel pressure because of a weak pump, restricted filter or leaky pressure regulator.

Loss of compression means the cylinder loses most of its air/fuel mixture before it can be ignited. The most likely causes here are a leaky (burned) exhaust valve or a blown head gasket. If two adjacent cylinders are misfiring, it's likely the head gasket between them has failed. Also, if an engine is overheating or losing coolant, it's likely the head gasket is the culprit.

You can isolate the weak cylinder by temporarily disconnecting each of the spark plug wires, one at a time, while the engine is idling. When there's no change in the idle speed, then you have pinpointed the weak cylinder.

Aug 25, 2009 | 2001 Ford Focus

2 Answers

What causes a misfire on a 99 pontiac grand am if spark plugs or good and the car does not have wires


here are the common causes of a missfire, defective ignition coil or ignition coil wiring for that cylinder, defective fuel injector, defective powertrain control module, intake manifold vacuum leak, low cylinder compression.

Aug 24, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
Cars & Trucks Logo

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...