Question about 2001 Ford Taurus

1 Answer

On my ford taurus a light with the car and bolt on the side.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,841 Answers

If you mean this warning light on my ford taurus a light with the car and bolt on - 5d07d41.png
then that means the fuel cap is loose. Tighten it 3 clicks. You really should get yourself an owner's manual. Go here where you can download your manual in PDF format. https://www.flmowner.com/servlet/ContentServer?pagename=Owner/Page/OwnerGuidePage

Posted on May 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specification for 1995 ford Taurus


4 Cyl Intake manifold bolts to heads = 15 to 23 Ft-lbs
6 Cyl 3.0L Step 1 = 11, step 2 = 21
6 Cyl 3.8L Step 1 = 7, step 2 = 15 & step 3 = 24 Ft-lbs
Tighten the bolts in secuence from center to out, alternating sides (front & rear); reaching the specified torque in several stages. I hope this helps. Take care.

May 25, 2014 | 1995 Ford Taurus

1 Answer

Steering knuckle will not go back into control arm need help 2002 ford taurus


Ford engineers should be shot for this. You can buy the special tool shown below. Use it to lift the strut and knuckle up enough to get the ball joint on. Or, loosen the engine cradle bolts on that side and drop the cradle down enough to bet the ball joint stud into the control arm. Ford engineers should be shot for this bad design.

http://www.freedomracing.com/strut-removal-set-6584.html?gclid=Cj0KCQjwnazLBRDxARIsAECdausVMQQttQlO0jefdGrbgC_BE8Bv-a-UC5E0w1OSdkKdZaGolyAklK8aAqa-EALw_wcB

Jul 16, 2017 | 2002 Ford Taurus

1 Answer

What are oil pan bolts torqued to??


You will need a Lb-In torque wrench , torque the 4 corner bolts to 106 Lb - In , then torque the remaining 14 bolts from back to front alternating side to side to 106 Lb -In

Oct 20, 2011 | 1998 Ford Taurus

2 Answers

How to change the right front turn pulb? 1998 ford taurus


unbolt the headlight (4 bolts on top, one of then is a tightening bolt, a long skinny bolt, try loosening that one, you can tell which one it is 'cuz there is no bracket on it.). Remove it then go in from the side you should be able to just reach the bulb socket, I think it twists out,you should be able to twist it with your fingers.

Jul 30, 2011 | 1998 Ford Taurus

2 Answers

Can't get the starter out of a ford Taurus 2004


either you took out the wrong bolt by the trans.... or the pin is stuck ... give it a whack with a mallet
should of taken out 2 ,13 mm bolts

Jul 28, 2011 | 2008 Ford Taurus X

1 Answer

My side view mirror on 200 Ford Taurus is loose from the top. All 3 of the bolt to mirror are tight. Could the top bolt be broken.


more likely a crack in the door where it mounts, did someone hit it possibly and not let you know

Jul 13, 2011 | 2000 Ford Taurus

1 Answer

Where is the starter located at on 1998 ford taurus


It is bolted to the side of the engine. The side that is closest to the radiator. Look up from the bottom. If it is a DOHC motor it is on the front side of the transmission bellhousing.

Sep 23, 2010 | 1998 Ford Taurus

1 Answer

How do you replace the brake light on a 1997 ford taurus


remove the trunk trim covering the tail lamp retainiing bolts .... remove bolts, remove tail lamp lens assembly...advise replace ALL the bulbs since your there, reverse steps to reinstall....not to tuff to do...hope this helps you...GL

Jul 06, 2009 | 1997 Ford Taurus

1 Answer

Front Sub Frame bushing 1995 Ford Taurus


it takes about a half an hour this is what you need to know th subframe holds all of your suspension wheel etc. they need to put car up on a lift get a seperate lift or its like abar they can hold the part they need lifted up drop the bolts out on the side they are replacing becuase you have 4 bolts holding the cradle in so they take out the 2 bolts out and exchange the bushing and then put it the bolts back in Please rate my response thank you very much

Jan 27, 2009 | 1995 Ford Taurus

1 Answer

Dodge intrepid 96


there are 4 bolts on the hood 2 each side/ take the top sheild off its retainers then remove front bumper reatianers and bolts on bottom and a bolt oneach side at fenders slide bumper off then you can get to lights and radiator you will have to unbolt the radiator brackets at the top should be able to replace them all

Jan 25, 2009 | 1996 Ford Taurus

Not finding what you are looking for?
2001 Ford Taurus Logo

Related Topics:

1,719 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...