Question about 2006 Nissan Frontier

1 Answer

I need to change both oxigen sensors on my Nissan Frontier 2006. Where are they located?

Posted by on

  • natty33024 May 10, 2010

    they told me in the mechanic that both sensors had to be replaced by they want $900.00 AMERICAN DOLLARS. they have to be kidding

  • natty33024 May 10, 2010

    it is a 4cyl

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

What makes you think they need replacement? they are in the exhaust pipe. V6? 4 cylinder?

Posted on May 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the location of crank angle sensor for the 2006 nissan frontier ?


On the bottom of the transmission bellhousing. Small sensor with a wiring connector, and 1 bolt attaching it to the bellhousing

Aug 10, 2014 | 2006 Nissan Frontier

1 Answer

2006 Nissan Frontier 2.5l PCV valave location


http://www.clubfrontier.org/ please go to this site. it is a lenghy job on this vehicle.when page comes up, just type in on left top of page--- pcv replacement on 2.5. good-day !

Apr 11, 2012 | 2006 Nissan Frontier

1 Answer

2006 frontier camshaft position sensor


If you do not know where the Camshaft Position Sensor is located, then it would be safe to assume that you have not properly tested the sensor or the circuits that operate the sensor. Therefore, you cannot possibly know for sure that it even NEEDS to be replaced...so why are you looking to replace it?

Nov 20, 2011 | 2006 Nissan Frontier

1 Answer

2006 nissan frontier ceck engine light on p2a00 circui range/performance bank 1 sensor 1


change your 02 sensor, bank 1 sensor 1 willl be a sensor screwed into a bung attached to the exaust before the catalyst. driver side

Nov 15, 2011 | 2006 Nissan Frontier

2 Answers

My 99 frontier will turn over fine but will not get fire from plugs i changed dist. cap and button. someone suggetsed that the coil might need replaced?


may be the crankshaft sensor not sure is it a 99 or 06 lol you show both. here is the location on the 99 hope this helpsonetufshoppe_77.gif

Jan 30, 2011 | 2006 Nissan Frontier

1 Answer

After changing a clutch in 06 nissan frontier i now have a spin no start . any suggestions? ps. already replaced crank pos sensor


was flywheel replaced? i've had this happen on one turned out sensor ring distorted on flywheel.went through three until i got a straight one.how did bx look it came in?watch intake cam timing pid while cranking.....should be very close to zero degrees.if not suspect sensor ring damage.l

Jan 19, 2011 | 2006 Nissan Frontier

2 Answers

Replacing knock sensor do I need to replace the harrness


No you don't have to change the harness unless it is cracked, broken, or have burn marks.

Nov 10, 2010 | 2000 Nissan Frontier

1 Answer

Locatio camshaft sensor 05 frontier 4.0 v6


on the back of the cylinder head. hard to see, but there is a connector with green slide piece inside of it. that is the location of cam sensors.

Sep 21, 2010 | 2006 Nissan Frontier

1 Answer

Nissan frontier 2005 won't star


when you check for spark check all cylinders u can use a regular spark plug and wire ground the plug end set the gap a little higher than veh calls for then yuoll know if it can have enogh to run all cylinders if you find only 2-3 firing thats still considerd no spark. hope this helps THUNDERBOLTZ

Jun 14, 2009 | 2005 Nissan Frontier

Not finding what you are looking for?
2006 Nissan Frontier Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...